9th April 1938, Page: 316, Column: 1
Water Troubles
At the March meeting of the Associates and Students' Section
of the North of England Institute of Mining and Mechanical
Engineers Mr. W. S. Hutton, Assoc.I.M.E., read a paper on
"Water Troubles," in which he said he had no doubt that all
mining men at some time or other had been troubled and had
anxious moments with water underground. He expressed the
view that, as the years go by, the necessity to take precautions
against waterlogged areas will increase, as the scattered, partially
worked, portions of various seams become necessary to prolong
the lives of the pits. Those blank sections (abounding in all
colliery plans), which have been left for no apparent reason,
those beautifully shaped pillars which have not been "brought
back," these are the mining man's lot in the future. It will be
his problem to tackle them, and Mr. Hutton thinks be can safely
say that fifty per cent. of these plague spots on the colliery plans
will give "water trouble" ; however, there is one consolation.
If the interruption in the normal development took place within
the last forty or fifty years, then anxiety might be reasonably
halved, inasmuch as the old goaf line or position of the unbroken
pillars will be fairly accurately laid down on the plans. Knowing
where the trouble lies is half the battle.
Mr. Hutton then proceeded to present the story of an attempt
on one of these "plague spots." The symptoms mentioned,
he said, were all there; a fairly extensive white portion of plan,
embroidered with intricate scallops of unworked pillars. The
approximate date of abandonment was 1815. The "white
portion" was roughly 500 yards diameter. The "embroidery"
extended half-way around to a depth of ten 20-yard square
pillars. The nearest approach lay within 400 yards of the coal-drawing
shaft and within 100 yards of an existing rolleyway
(engine plane). The seam was 11 feet thick. The temptation
was great, and they were led into it and the evil was delivered
unto them there was an added inducement also. The old plan
stated that operations in this particular area had been stopped
because of the excessive inclination of the seam. They had
worked the seam immediately underneath this area and invariably
adopted self-acting inclines, the gradient being approximately
9 inches to the yard. They pictured the difficulties the old miners
must have had working to the dip with such an inclination.
They were inclined to think that the excessive gradient had been
the sole reason for ceasing work in this area. They drove two
drifts from the lower seam to the upper (the area to be worked).
The vertical distance intervening was 42 feet and the strata
penetrated was mostly massive sandstone. The fore drift was
driven 1 in 6 and the back drift 1 in 3.
The method of work was bord and pillar, the seam being cut in
the middle with a percussive-heading-machine. This method
proved very successful. The cost to the shaft was one which
every colliery manager strives for and seldom attains.
The west side places began to "bleed," and Mr. Hutton
explained that as they reached tire boring line they were stopped.
Then it was decided to advance the back-winning to the boring
line and commence boring. The aim was to tap the old workings
at practically the highest point possible, in order to maintain a
better control over any water, which they now fully expected
to get when we holed. The boring was done by means of
"Burnside" boring gear adapted for use with compressed air.
The work of boring and advancing of the heading proceeded
into the fourth week, by which time the back-winning had
advanced 32 yards into the barrier. Then there were further
water troubles, and the idea of piping the water to the shaft
standage was abandoned. The shaft pumps would only deal
with 600 gallons per minute and there were 300 gallons per
minute coming to the shaft from other parts of the pit. It was
decided to seal up each drift with a brick dam, the fore drift
to be sealed first. Mr. Hutton gave details of the building of the
dams, each dam having a total of 15 feet depth from convex
facing to outer facing. Both dams were duly completed.
Small feeders of water were forcing their way through fissures
in the roof and sides adjoining both dams. These were ultimately
stopped by drilling a series of holes in the sides and top over the
of the dams, into which cement was injected by means of a
cement gun. The mixture used for grouting was 50 per cent.
cement and 50 per cent. sand. The maximum amount of water
in the feeder amounted to 600 gallons per minute.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Hutton, W. S. | | | |