Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

26th March 1938, Page: 292, Column: 1

Use Of Pneumatic Picks

By H. E. Morgan, Assoc.I.M.E.

Extracts from paper on "The Use of Pneumatic Picks as an Aid to Coal Getting," read at the February meeting of the Associates and Students' Section of the North of England Institute of Mining Mechanical Engineers.

This paper gives details relating to the introduction and application of pneumatic picks. The seam has an average thickness of 3 feet 6 inches and lies at a depth of 1,600 feet from the surface. The roof consists of from 0 to 7 inches of mudstone, with strong sandstone above, and the floor of from 10 to 15 inches of poor quality fireclay with coal partings underlain by strong "white" seggar. Cleavage planes are well defined and close together. The top section (2 feet 6 inches) of the seam is of medium hardness and the bottom section (1 foot) is of greater hardness. No definite stone bands are present in the seam, but "post" stone balks are frequently found. The area of coal worked was badly cut up by faults (up to 45 feet in throw). Floor movement, in regard to all methods of working, was severe and rather rapid. The gradient of the normal seam was 1½ inches to 2 inches per yard.

Pony putting and main and tail haulage Were the methods of transport used.

Approximately the proportion of coal obtained by the various methods of working was: Longwall gateways, 40 per cent. of output; bord and pillar (whole workings), 20 per cent. of output; bord and pillar (broken workings), 40 per cent. of output.

Previous to the introduction of pneumatic picks the coal had been worked, during periods of considerable lengths of time, by cutting machines (of the percussive heading type), by stubbing machines (of somewhat similar type), and by hand-hewing. The application of none of these methods had resulted in satisfaction as regards cost, or output. The change-over to pneumatic picks did not reduce the number of workmen required in the district, but each coal-getter obtained a greater output per shift, and therefore higher wages, with less arduous labour. With regard to the application of cutting machines, stubbing machines or pneumatic picks, in each working set there were, normally, two coal-getters per shift. One man operated the machine and the other filled the coal into the tubs. When not so occupied the second man worked with an ordinary hand pick.

Despite a reduction in working hours, the change-over to pneumatic picks resulted in increases in output per man-shift at the coal face, and comparing the results obtained as affecting the entire seam, and concerning in each case approximately 18,000 man-shifts at the face, the output with pneumatic picks was 82 per cent. higher than with stubbing machines.

During certain periods since the change over to pneumatic picks, it has been necessary for workmen to revert to hand-hewing. The result has been a severe drop in the output per man-shift at the face, usually 50 to 60 per cent. reduction.

Comparative Advantages.

Advantages of using pneumatic picks, as compared with cutting machines or stubbing machines include :—

1. The initial cost of a pneumatic pick was only about one-sixth of that of a stubbing machine, and cost of repairs and renewal of parts of machine correspondingly lower.

2. The consumption of compressed air for pneumatic picks was only about one-quarter of that for the stubbing or cutting machine.

3. One man could handle a pneumatic pick, but two men were necessary to move or set a stubbing or cutting machine (to avoid excessive loss of time):

4. With a pneumatic pick the coal-getter was able to commence coal getting as soon as he had completed his examination of the working place.. With cutting or stubbing machines a considerable amount of time was lost when setting the machine or moving it about the face (especially in longwall gateways), and in arranging the face supports.

5. Should a man be idle the effect was very noticeable in the case of stubbing machines — the output of one man was usually equal to less than half of that produced when both men were at work. When using a pneumatic pick, if one man was idle the output of the other man was usually equal to more than half of that of the two men.

6. Flitting from place to place with a pneumatic pick was accomplished in a much shorter period of time and with less inconvenience, or danger, than with a stubbing or cutting machine.

7. When encountering broken roof, uneven floor, or change of thickness of seam, much difficulty arose in connection with stubbing or cutting machines as regards setting the machine firmly and in adjusting it to suit change in height.

8. A considerable quantity of spare parts, for stubbing machines and cutting machines, had to be kept readily available in the pit, hut in regard to pneumatic picks — a few spare machines were kept. In case of breakdown, the defective machine was sent to the surface fitting shop where it could be most efficiently repaired.

9. Cutting machines are connected with three serious disadvantages as compared with the other machines or with hand-hewing (a) The necessity for additional pit-room, for a similar number of men; (b) The necessity regarding the firing of shots and the added dangers which arise as a result of such necessity, also giving rise to additional work and responsibility for deputies, etc., and increased cost of production owing to use of explosives; (c) Owing to rapid floor movement the rods were often held fast in the cut — juds were not completely cut and much time was lost.

Advantages of using methods of getting other than by pneumatic picks :—

1. The cutting machine or stubbing machine may be more effective than the pneumatic pick when the cleavage planes are not well defined, or if the coal is of a very hard nature.

2. Hand-hewing does not create an amount of noise equal to that created by a pneumatic pick in action and, from that point of view, may be less dangerous.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Morgan, Harold Eustace      Whos Who Page


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print