|
12th March 1938, Page: 278, Column: 1 Capping Of RopesBy M. A. Hogan, D.Sc., M.Inst.C.E. Extracts from paper on "Some Notes on the Capping of Winding and Haulage-Ropes," read at the February meeting of the North of England Institute of Mining and Mechanical Engineers. The safety of winding or haulage Systems depends on the strength of the capel just as much as on the strength of the rope. The capel should be capable of transmitting the force in such a way as to develop the full strength of the rope. Other essential requirements are that the capel must maintain a satisfactory grip on the rope throughout its period of service, that it should be easily fitted, and that the weight and outside dimensions should be as small as possible. The legal requirements with regard to the strength of capels are set out in Regulation No. S of the 1937 Winding and Haulage Regulations: "No mode or type of capping shall be used which falls to withstand, for a winding rope, a load of at least seven times the maximum static load and, for a haulage rope, a load of at least 60 per cent. of the breaking strain on the rope." The failure of a capel in service is normally caused by repeated stressing (fatigue), and failure by a single tensile stress only occurs in the event of a collision or other accident in which the cage is held fast. For this reason capels should be designed to offer a high resistance to fatigue, and if this is obtained the strength in a static tensile test will usually be satisfactory. Types of Socket. Sockets may be divided into two groups, solid and split. Solid sockets have the hollow conical "barrel" made in one piece, whereas in split sockets there are two side portions connected by solid rings driven on outside. The solid type may be subdivided into open and closed sockets. In an open socket the end facing the load has two lugs, one at each side, with holes to receive the pin by means of which the load is attached; the end is open so that the enlarged end of the rope may be drawn straight in. In a closed socket the side lugs are continued to form a solid bow to which the load is attached. In the older forms of capel where a split socket with a solid end was used, the bow had to be heated to enable the sides to be opened or closed. Local heating of a portion of an iron capel is undesirable because there is a risk that the metal at some part will be worked at an unsuitable temperature. There is also a danger that the socket may be so hot as to damage the wires of the rope, or at any rate to cause the lubricant to flow out of a cone of bent-back wires. The mechanical design of sockets should follow modern practice and take into account the effect of various details on the resistance to fatigue. For example, sharp corners should be avoided, the junctions between the surfaces being finished with a smooth radius, and all changes of section should be gradual. The pin-holes in the side lugs of open sockets should be set back from the end of the lug so that the distance from the hole to the end is not less than 1.3 times the distance from the hole to the side of the lug. The material in the socket should work with a higher factor of safety than is required for the rope or for the capel as a whole. In view of the liability of capels to suffer shock loading, e.g., due to starting a wind with slack chains, they are commonly made from a very ductile material such as wrought-iron, or dead soft steel, having a considerable amount of elongation before fracture. Types of Capel. All the common types of capel depend on friction for their operation, and only in exceptional cases, such as where the strands are spliced back into the rope or a knot is formed on the end, is the rope directly held. The capels which operate by friction may be classified under three headings depending on whether the force is applied (1) to the wires, (2) to the strands, or (3) to the rope. White-metal capels in which the individual wires are opened out and cast into the metal fall into the first class. The second class comprises capels in which a conical wedge is inserted between the strands to form an enlargement on the end of the rope and the individual strands are held by friction developed between the cone and the socket. In the third class there are several types the side-compression type in which the rope is held by friction in a groove between two steel plates; the type in which the rope is taken round a thimble and held back on to itself by clamps; and the type in which the thimble is drawn up against a socket by the tension of the rope. The various forms of bent-back wire capel also fall into this group because, when properly made, the rope is held by the friction developed by the wedge of bent-back wires. In British winding practice the provision of detaching apparatus has practically eliminated the use of capels in which the rope is clamped around a thimble, or in which the thimble is drawn up into a socket, because of the necessity of ensuring a free passage for the capel through the detaching bell. In selecting a capping metal the first point to be considered is the pouring temperature, which should be low enough to avoid damage to the wires. The fluidity of the metal at this temperature is of importance because of the need for ensuring penetration right down to the small end of the socket. When the metal has cooled it must develop a satisfactory degree of adhesion to the wires and be strong enough to avoid any liability to flow under the heavy pressures existing in a capel. The pouring temperature adopted in B.S.S. No. 643, namely, 350°C. (660°F.), was selected from a consideration of the effect of heat on the tensile strength and stress-strain curve of hard-drawn steel-rope wire. Observations on capels made at collieries and in the laboratory showed that wires are seldom or never tinned by the metal (even when the high tin alloy is used) but are held by a frictional grip. The contraction of the white metal on solidifying and cooling to atmospheric temperature produces compressional forces sufficient to develop a frictional resistance of the order of 700 lb. per square inch of wire surface. This figure applies to a straight wire, but a wire slightly curved and twisted, as in a rope capel, may develop a resistance up to three times this amount. The presence of a thin film of grease destroys the frictional grip. Cleaning the wires with emery cloth, and the use of powdered rosin, results in improved adhesion, even though the wires are not tinned. The cleaning of the wires is the most important point in the making of a white-metal capel, and most of the failures which have been examined have been due to the neglect of this obvious precaution. Besides cleaning the wires by removing the grease with petrol and polishing with emery cloth, powdered rosin should he dusted into the capel to act as a flux when the metal is poured. The socket should be heated to about 100°C. in order to avoid chilling the metal too rapidly and to enable it to penetrate down to the narrow end. The temperature of 100°C. was chosen as a result of numerous observations of colliery practice and laboratory experiments. It is the highest temperature which can be used without causing sufficient heating of the rope to cause the internal lubricant to run out near the capel. Ordinary rosin melts about 100°C., and so the correct temperature is that at which a piece of rosin held in contact with the capel begins to melt. There is some difficulty in cleaning the wires of a large rope, and in order to reach the inner wires those of the outer layers may have to be bent outwards practically at right angles. If the wires are bent too sharply they may be damaged, and will subsequently fail in fatigue at the mouth of the capel. This trouble may be avoided by fitting a clamp with a bell-mouthed opening over which the wires can be bent. Another important precaution in making a white-metal capel is to ensure that the rope is symmetrically placed with respect to the socket so that the loading on the rope will be axial. This is done by clamping the socket with the large end uppermost and with a length of not less than twenty-four times the rope diameter hanging vertically below the socket. In capels in which the strands arc held by friction the capel generally consists of a cone, smooth or grooved to fit the strands, which is inserted in the centre of the rope to form an enlargement on the end. The enlarged end is held in a solid, or sometimes in a split, socket. In laboratory tests haulage capels with mild-steel or copper cones have given good results, but in practice there is some danger of the cone falling out. A method of retaining the cone which has given good results in service is by the use of a "tail strand" cast into the cone and run into the rope in place of the core. The following points may be mentioned in favour of this method of capping: (1) It can be done underground, as no molten metal is required when capping. (2) The quality of the capping can be determined from an external examination (i.e., whether the strands lie properly in the grooves). (3) The amount of manipulation required is less than with other types of capel applicable to underground haulage ropes. (4) The strands are gripped evenly (the grooves ensure this) and the rope is axially loaded. (5) The B.S.I. "Short" socket used is considerably lighter than the sockets required with heat-back-wire capels. (6) If the capel is- properly made it is impossible for the components to become displaced, and efficiencies of 100 per cent. are regularly obtained under test. (7) It may be used either with round- or flattened- strand ropes. Capels in which the rope is held by side compression are characterised by the provision of a pair of long grips, each provided with an almost semi-circular groove to fit the rope. The free space between the two grips is usually about 1/8th of the rope diameter. The rope is held by friction against the surface of the grips, which are usually made of cast steel. A compressive force equal to about four times the rope tension is required to clamp the, grips on the rope and enable the necessary friction to be developed. Regarding capels in which the rope is held by a cone of bent-back wires, this is one of the oldest forms, and when properly made the capel is capable of developing the full strength of the rope. The chief objection is the difficulty in making the capel and the fact that its strength is entirely dependent on the skill with which it is made. The most important point in this type of capel is that the rope should be gripped along the whole length lying within the socket by the pressure developed by the cone of bent-back wires and seizing. A satisfactory cone of bent-back wires cannot be made. much shorter than eight to ten times the diameter of the rope, and hence the length of the socket into which the cone fits should not be less than eight rope-diameters. Capels in Service. In the course of the investigations of the Wire Ropes Research Committee eighteen capels that failed in service on winding ropes have been examined. Six of these were of the white-metal type, nine had bent-back wires, one had bent-back strands, and two were of the wedge-compression type. The majority of these failed because of some fault .in the method of capping, but four -(two white metal, one bent-back wires, and one bent-back strands) failed because little or no rope had been cut off at recapping so that the wires at the end of the capel had been seriously weakened by corrosion-fatigue. Two of the white-metal capels failed because there was a cylindrical length at the small end of the socket within which the wires were nicked and failed by corrosion-fatigue. Two others failed because the wires had not all been properly cleaned, and sufficient oil remained on some of them to destroy the adhesion. The wires which were held by the metal being overloaded failed in fatigue, and the others then drew out of the capel. Three of the bent-beck-wire capels failed because a ring had been used as a base for the cone of wires, and three failed because the end of the cone had been run in with white metal. One failed because the pin driven into the end of the rope had cut the strands. Another failed as the result of deterioration by corrosion-fatigue which was accelerated by the use of copper binding wire. One of the failures in the compression-grip type of capel was due to corrosion-fatigue which resulted from the use of a rope which was too small for the load. The other was attributed to damage to the rope caused by driving on the last capel ring (at the small end of the socket) too tight. Besides the winding rope capels which failed a large number of other capels used for winding and haulage have been examined. The general conclusion to be drawn is that most of the capels in use are of sufficient strength when properly made, and that the direction in which present practice is most likely to be improved is by the simplification of the methods of manufacture so as to exclude as far as possible any risk of failure through lack of skill in fitting. One of the commonest troubles experienced with winding-rope capels is the breakage of wires just at the mouth of the capel. If the operating conditions are such that the occurrence of slack rope during normal winding cannot be avoided, frequent recapping is probably the best remedy. Other remedies which have been applied under these circumstances include the provision of hard rubber blocks at the end of the wedges in the side-compression type of capel, and the provision of a semi-flexible extension to the white-metal type of capel. In placing a stranded rope between the two wedges of a compression-type capel it is desirable to ensure that at the end of the wedges the grooves between pairs of strands at each side of the rope should coincide with the gaps between the wedges. The object of this precaution is to prevent one strand at either side from bearing against the corner of the wedge, because this has been found to be a frequent cause of broken wires. Capels made with an enlargement on the rope end formed by splicing back the strands into the rope are used on haulage ropes and occasionally on winding ropes. Although this method of capping may develop an adequate amount of strength in a tensile test, it cannot be considered entirely satisfactory, because the severe bearing stress to which the wires are subjected where one strand is tucked in behind another causes a reduction in their resistance to fatigue and the fatigue strength of the capel is low. Haulage capels in which a knot is used to hold the rope in the socket have a reduced fatigue strength because of the bending of the wires in the knot.
|
|||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||