|
29th January 1938, Page: 233, Column: 1 Hydraulic Coal BursterFrom the last published Report by Mr. H. J. Humphrys relating to the Yorkshire Division the following particulars concerning the use of coal bursters are culled :— At the Hickleton Main Colliery seven bursters are in use on conveyor faces in the Parkgate Seam five feet thick where the coal is holed by a machine to a depth of four feet in a dirt band 20 inches above floor level. Holes are bored four inches in diameter by compressed air machines. Where the faces are at an angle of 45 degrees to the cleavage teams of three men are employed on the filling shift, after the loose coal has been taken down, to bore and burst the holes. Each team deals with 25 holes per shift, and the holes are put in where and when required. On the "end" faces holes are bored below the dirt band before cutting commences and above it on the filling shift, as in the case of the "half and half" faces. Shot-firing has been entirely eliminated in coal except on a short length of face where coal is left to form a roof and there is no parting between the coal worked and that left up. The bursters have been in use four months and it is estimated that 100,000 tons of coal have been forced down by their agency. The advantages over shot-firing claimed are: (1) Better roof; (2) No fumes or possibility of flame or spark; (3) No need to withdraw men whilst coal is being burst; (4) More round coal and better size for handling. Four bursters have been in use in the Haigh Moor Seam at Barnsley Main Colliery over a period of two years. Shot-firing in coal has been entirely eliminated and 250,000 tons of coal have been burst down. The burster holes, four inches in diameter, are put in six yards apart and six inches from the roof by compressed air drills, and are burst during the filling shift. The seam is undercut to a depth of five feet by machine. Shot-firing in rippings has been abolished by the use of pneumatic picks. Two bursters have been in use in the Parkgate Seam at Barrow Colliery on one face for three weeks and on the other for six months. Shot-firing has been eliminated on the latter face and it was hoped to achieve the same result on the other face. The quantity of coal burst down is 14,000 tons. The holes, four inches diameter, are put in by compressed air drills six inches and two feet below the roof alternately. In each row the holes are six yards apart. They are put in before the seam is undercut to a depth of five feet and burst during the filling shift. One burster has been in use in the Thorncliffe Thin Seam at Grange and Bradgate Colliery for about a year and about 66 per cent, of the shot-firing in coal has been eliminated. Twenty-five thousand tons of coal have been burst down. The burster holes, 3 3/8 inches diameter, are put in by electric drills. Experiments have been made to bring down the hind ripping in which are layers of ironstone. The result has been that (1) better packers have been produced, and (2) the roof and sides of the road are stronger. Eight bursters have been in use in the Beeston, Silkstone and Yard Seams at Water Haigh Colliery over a period of nine months. Rippings were, and are, brought down by pneumatic picks, but shots were fired in coal. These have now been entirely eliminated in the districts where the bursters have been installed, and it is hoped to extend the bursters throughout the mine. The amount of coal burst down is 100,000 toes. In the North Midland Division Report Mr. J. R. Felton refers to the use of seven bursters at Ireland Colliery. He says they have proved entirely successful, and by them shot-firing has been almost completely eliminated. They are also used for ripping. The holes for the burster are bored 12 inches from the top of the seam, just above a four-inch band of "hards"; they are normally 11 yards apart, but in difficult places an extra hole is bored three feet away just below the band of "hards." The main gate ripping requires three holes, one at each side just above the 18 inches of tops and one higher up in the middle, whilst the tail gate rippings require only one hole. The clod is got down by hand all along the face. As the result of the experience of managers under varying conditions Mr. Felton gives the following observations which he hopes may prove of assistance to others who may be considering the adoption of the "burster" :— (1) It would seem that its effectiveness in coal depends upon the nature of the seam; the coal must be undercut, must part fairly readily from the overlying roof, and be of not too tough or "wooden" a texture. In ripping the nature of the strata is again important. The drilling of large diameter holes in ripping lips might prove difficult where the strata are very hard, and where the strata are of a softer nature pneumatic picks could probably in most cases be used as effectively and cheaply. (2) Experience has shown that this device, though not suitable for all conditions, has considerable possibilities. Where round coal is wanted, for example in house-coal seams, it has proved advantages. (3) The device under suitable conditions is certainly a practical substitute for explosives in coal on longwall faces. Where it has been tried shot-firing has been substantially reduced if not wholly eliminated. In the last Report by Mr. E. Rowley, covering the Midland and Southern Division, there is an indication that the use of the hydraulic coal burster is extending. It is in use at three pits in the Division, and at one of them, Newdigate Colliery, the total output is won in this manner. The burster was first used at this colliery on a face where the coal was somewhat hard and "grizzly." The experiment was not immediately successful, but the management persevered and about six months later the whole Output was being obtained without the use of explosives. This Mr. Rowley describes as a very fine achievement, and the management deserves every praise for their enterprise and skill. The Inspector also says the burster possesses many advantages, e.g., accidents caused by explosives are completely eliminated, there is an improvement in the quantity of round coal, the coal is not so shattered and therefore breaks less in transit, men do not have to leave the face when the coal is being blown, and the cost per ton is, if anything, slightly less than when using explosives,
|
|||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||