15th January 1938, Page: 217, Column: 1
Metalliferous Mine Shafts
In a paper on "Metalliferous Mine Shafts — Various Types and
Equipment," submitted for discussion at a meeting of the Institution
of Mining and Metallurgy, Mr. G. F. W. Trestrail said the
first problem of underground mining is the selection of an entry
site, and the deciding factors are usually the surface topography
and the type of deposit. Where possible, crosscut tunnels form a
secure approach, and drifting by adit is of remote antiquity;
while the use of shafts following the pitch of the vein is a traditional
means of access.
Historically, the shape and structure of shafts are peculiar to
the various mining districts. Cribbing was employed by the early
miner as a means of support, and lent itself to rectangular shafts.
In the north of England, circular shafts lined with dry stone
walling are in evidence. Many of them are 4 feet in diameter,
and are sunk through as much as 100 feet of boulder clay. Hardwood
curbs, shaped to the radius of the walling, are inserted at
intervals and protect the structure from collapse. Either as
means of escape, or to promote ventilation, or because of their
small dimensions, many shafts were sunk. In the absence of
adit drainage, the depth of mining was restricted to some 20
fathoms by the crude pumping appliances and lack of operative
resources. Shaft enlargement and sectional bratticing began with
the introduction of the Newcomen engine, when the new pumping
equipment required much of the shaft space. Although the
atmospheric engine was inefficient, it made deeper exploration
possible, and in the half century of its existence shafts attained
a depth of 80 fathoms.
Consequent upon the inventions of Watt, and the coming of
the steam age, development was rapid, and by 1800 several shafts
approached the 1,000-ft. horizon. Much of the antiquated
structure remained. The horse-propelled whim and the bucket
pump became ponderous as depth increased and irregular descent
made operation difficult. The use of steam at high pressure
widened the field of activity, and the development of the beam
engine and plunger pump was of outstanding importance.
Another notable achievement was the adaptation of the beam
engine to rotative motion, and its application to mineral hoisting.
In the deeper mines, the absence of transport for the miners
was an acute difficulty. Ladders were of great length, often
perpendicular or overhanging, and the task of climbing them was
arduous. The colliery practice of hoisting men with ropes was not
acceptable to metal miners, and the difficulty was not solved
until the invention of the man-engine, which was introduced
into British mines in the 'forties. Half a century later the cage
came into use, and much constructional ingenuity was displayed
in guiding its passage through the erratic descent of the shaft.
The turned vertical shaft was common.
The closing years of the nineteenth century witnessed a period
of intensive mining. Assisted by the pneumatic rock drill, which
had recently been developed to a state of useful efficiency, and by
the more powerful types of nitro-glycerine explosive, mining
approached the 3,000-ft. horizon. Shafts of inadequate capacity
and remote accessibility, commenced in the infancy of the mines,
had exceeded their useful life, and set a limit to further advance.
Confronted with the necessity for deeper development and increased
output, the miner found a solution in central access by vertical
shafts.
Of the modern shafts inaugurated some forty years ago, the
rectangular type was retained on the Rand, while the circular type
was favoured at Kolar and in Cornwall, where two circular brick-lined
shafts were extended some 3,000 feet.
At the Basset mine, the Marriot shaft was the most heavily
watered, and a pumping system to elevate two million gallons
of water per day, and cage hoisting at a rope speed of 2,000 feet
per minute, were provided.
The Gifford shaft at the Champion Reef mine of the Kolar Gold
Field was extended 3,800 feet vertically from the surface; this
brick-lined shaft is 18 feet in diameter. The equipment consists
of a steel centre member and guide rails of 90-lb. section. Hoisting
is by 6-ton skips, and the double-deck cages transport 50 men
per trip. The Heathcote shaft extends vertically from the foot
of the Gifford shaft and deals with the output of the deep level
workings. The structure is of elliptical formation, 18 ft. 6 in. x
12 ft. 6 in. axial dimensions, and is concrete lined. The equipment
consists of Oregon pine runners and hard-wood cross members.
Transport is by double-deck cages and trucks. Continuing below
the Heathcote shaft are the north and south development winzes.
These also are of elliptical section, measuring 16 ft. 6 in. X 11 ft.
6 in., and are equipped with single-deck cages in tandem.
In the Lake Superior mining region, shafts of 9 ft. x 20 ft.
were not uncommon, and several at Calumet and Hecla were
3,000 feet deep at the close of the nineteenth century.
Modern Conditions.
Following particulars of shafts in various mining areas, as
indicated in Bulletin No. 398 of the Institution Mr. Trestrail
concluded his paper by saying that throughout the ages the
urgent problem of mining has been the removal of water, and,
as depth increased, the lack of mechanical efficacy was a barrier
to progress. The design of shafts was formerly influenced by
the necessity for providing space for massive pumping equipment,
but with the introduction of the centrifugal pump the space
required has been greatly reduced. Mining is now approaching
the 9,000 ft. horizon, and the greater depth has brought forward
the problem of cooling, which is one of the main considerations
of the shaft designer to-day.
It seems likely that the factors which will finally limit the depth
of mining will be the physiological effects of the atmosphere, and
the ever-increasing rock pressure. Although the origin of mineral
deposits is obscure, there is nothing to suggest that they will not
persist to depths greater than those already known. Of the
economic aspect, whilst the relation between the value of the ore
and the cost of production determines the grade of workable
material, these are both capable of variation.
Whilst mechanical equipment is abreast with existing requirements,
the transmission of motive power, apart from the isolated
uses of electricity, is confined to compressed air because of its
convenience as a medium of power transmission to underground
services and incidentally as a means of ventilating workings
inaccessible to normal air-currents. Notwithstanding the increasing
employment of this form of power transmission, the
inherently low efficiency of the system is reflected in the unit
ratio of air compressed to tonnage mined.
The record achievements in recent years in shaft sinking and
the breaking of ground owe much to the development of the
numerous types of rock drills, the improved composition of drill
steel, and the recent innovation of hot-milling and furnace temperature
control.
The wire rope has undergone many changes since it replaced the
hemp rope a century ago. The weight of a rope and drum of large
circumference became cumbersome with increasing depth, and
the flat rope and reel, and later the tapered rope, then came into
use. The Bessemer process gave a wider choice of material, and
modern rope construction approaches the ideal which has made
deep hoisting possible: namely, flexibility and strength, combined
with a reasonable weight, and the inclusion of more wires of
high tensile strength in a confined area.
Ultra-deep hoisting has been made possible mainly by the
uniform torque of the electric hoist and the recent technique
of brake control. By means of a non-elastic medium in the form
of oil at constant pressure in the brake cylinders, smooth response
of the drum control system is assured and the kinetic stress on
the rope is reduced. The use of light alloys has also contributed
to the success. Whilst a relation exists between the hoisting
capacity and the depth of wind — the limitation is the factor of
safety of the rope — there appears to be no limit to the depth of
stage hoisting, apart from economic considerations.
Choice of transport is mainly influenced by local conditions
and, whilst the form of vehicle is arbitrary, tub hoisting by means
of the cage is essential to grade classification. The skip is a
progeny of the inclined shaft. With its early features of long
rectangular construction mounted on flat treaded cast-iron wheels,
bottom discharged through a man-operated door and by the
simple arrangement of "self tipping," it became a common means
of mineral transport. The principal — single hoist — shaft
presented
a difficulty, in some cases there was a provisional change from
skip to cage, in others the tub-cage system was adopted, and where
the hoisting of mineral was the primary consideration, the skip
retained its precedence. By modern methods, the loading and
discharging are accomplished in the minimum of time and the
system is capable of large outputs.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Trestrail, G. F. W. | | | |