|
1st January 1938, Page: 196, Column: 1 Coal Preparation TechniqueSizing and Grading of Yorkshire CoalsIn the section of the Fuel Research Board's Report on the preparation of coal for the market it is explained by Dr. F. S. Sinnatt that the examination of the screen analysis of the smaller grades of coal produced at a number of collieries in South and West Yorkshire has been completed by the staffs of the Coal Survey at Sheffield and Leeds. This work is being carried out for a joint committee of the Midland Institute of Mining Engineers and the South and West Yorkshire Coal Owners Associations. Preliminary information had shown that 106 different size grades (including "slacks") were marketed in this area, and it was desired to reduce the number of these grades marketed. With this end in view it was decided to ascertain the actual size analysis of the material prepared in practice at the different collieries. As a preliminary it was necessary to establish methods for sampling and screening, and it was decided to use hand screening on square-mesh screens. A technique was adopted which would reduce breakage and attrition to a minimum. Experiments were carried out to determine the size of sample and the number of increments necessary to obtain reproducible results. After these preliminaries had been settled, 64 collieries were visited and 78 grades of trebles, 82 of doubles, 96 of singles and 86 slacks were examined. The resulting data have been analysed by the Committee, who put forward a suggested classification. This classification retains the major divisions of trebles, doubles and singles, and to specify adequately sub-sizes within the major divisions, it has been found desirable to employ four test screen limits. The designations of the three sub-sizes of the Trebles and Doubles are similar, and there are two large and two small Singles sizes, each with its specific upper and mid limit but with common lower limits for the large Singles and small Singles. The investigation has clearly shown that uniformity of screen apertures does not of itself give uniformity in the size of product. The method of test adopted in the investigation gives precise information in respect of the size of the marketable product, and consequently has regard to the efficiency of the screening and loading plant at the collieries. If the scheme be adopted, this method will also be used for checking the correctness of the sizes marketed. Treatment of Fine Coal. Under modern conditions of mining it is inevitable that considerable quantities of fine coal, often containing a relatively large proportion of dirt, should be produced, and there is every indication that the need for improved technique for dealing with fine coal is becoming more generally recognised. Slurry. — One example of this scientific development of coal preparation technique is the widespread interest in and adoption of slurry flocculation processes. Experience suggests that, provided the flocculating agent is chosen to suit the particular slurry to be treated as regards both the effect obtained and the cost of the treatment, the result is in general satisfactory. The process has thus passed out of the experimental stage and it remains to be seen whether the treatment of slurries in this way will become a permanent feature of coal cleaning technique. Cleaning Fine Coal. — At the present time there are three points of view on the question of the commercial washing of fine coal: (1) That it is best not to wet any coal finer than about 1/8 in., but to separate this material from the coal before washing and if possible to return it in an uncleaned condition to the larger cleaned sizes; (2) That the fine coal should be washed in a plant specially designed for material of this size; (3) That with a suitable type of washer the fines are adequately cleaned in association with the larger coal. Satisfactory means of cleaning the fine coal are called for, and recent Reports have dealt with the possibilities of "vacuum flotation." Of the other available methods of cleaning fine coal, that of the "Minerals Separation" process is well known and some plants are at work cleaning coal by this method. There is, however, another process, not yet used for the cleaning of British coals, which has some points of similarity with the above, but which differs from it in that (a) the air required for flotation is forced by a blower through a porous mat in the bottom of the flotation cell and (b) the pulp is not subjected to vigorous agitation. The most convenient way of cleaning fine coal would be by treating it in association with coarser material, so that no additional plant would be required ; to some extent this is possible in certain types of machine, notably the jig washer. Lack of knowledge has led to very unfavourable views of jig washing being expressed in certain quarters, and it has even been said that coal finer than 1/8 in. cannot be cleaned in this way, and that any coal of this size in the raw feed passes through the washer uncleaned. Since this view is not in accordance with the information at present available it appears important that the position should be further investigated and made known, so that a decision as to the best typo of washer for use in any particular instance may be based en reliable information. Arrangements are therefore being made to collect details of the efficiency with which fines are cleaned at a number of colliery washeries. "Desliming" Plant. The first experiments on the removal of readily dispersible material, consisting mainly of fusain and clay, from coal by wet screening, were carried out in connection with the cleaning of certain low rank coals. These coals could only be cleaned by vacuum flotation after the finest "slime" had been removed in this way. A plant has therefore been designed and constructed at the Fuel Research Station capable of desliming the coal prior to treatment in the large-scale vacuum flotation plant. In some respects the desliming process resembles dedusting, which is commonly adopted to alleviate the slurry problem, but it should be noted that desliming differs from deducting in the following two particulars: (a) The efficiency of desliming is not decreased when the coal feed is damp ; (b) Shales that disintegrate in the washer to form slurry are more effectively removed by desliming. In its present form the desliming plant consists of a metal cylinder 4 ft. diameter and 6 ft. long, to which is fixed an internal helical spiral. The axis of the drum is inclined to the horizontal and, by the slow rotation of the drum on its axis, the coal and water which are introduced at the lower end are mixed and conveyed to a de-watering screen. This screen is 8 ft. 6 in. long and 20 in. wide and is composed of wedge wire having a mean aperture of 0.3 mm. It is provided with a clean-water spray near its lower end, and the slightly contaminated water through this lower section of the screen is used for spraying the coal on the middle section. The dirtier water from this stage is introduced into the drum with the raw coal, and the final effluent from the plant is that which drains away from the coal when it pours from tile drum on to the upper part of the screen. The effluent amounted to ton per ton of feed coal, and was thus only about a tenth of the amount of water used in many washers. The solid content of the slime or slurry effluent from the machine in the experiment was 14 per cent., which is sufficiently high to indicate the possibility of dispensing with thickening by sedimentation, and of recovering the solid matter by feeding direct to a drum-type filter. An alternative method of dealing with the effluent in some instances would be by froth or vacuum flotation for the recovery of the combustible material it contained ; the above-mentioned solid content of the effluent is approximately that which would be required for this process. An aspect of desliming that has not yet been considered is the possible influence on the coking properties of certain coals and blends, and it is hoped to study this question in later experiments. "British Geco" Froth-flotation. The experimental apparatus for this process consists of a cell, which is almost cubical in shape, having a perforated rubber mat fixed in the bottom. Air from a low-pressure blower is passed through this mat into the coal pulp contained in the cell, where the bubbles are dispersed by a smooth rotor which does not agitate the pulp. Experiments have not yet been completed, but the following conclusions are indicated by the results obtained up to the present : (1) Coal coarser than 1/16 in. is not so readily floatable by this process as by vacuum flotation. (2) Both "collector" (e.g., neutral oil) and "frother" (e.g., cresol) are necessary for the efficient recovery of most coals, whereas only a "collector" was necessary for vacuum flotation (3) The amounts of oil required for the efficient recovery of coals of various rank tend to increase with decreasing carbon content of the coal substance. This apparent correlation with coal rank is in accordance with the results of the experiments on vacuum flotation. Two important details of froth flotation technique are (a) the solid content of the coal-water mixture to be treated, and (b) the "conditioning time" — that is, the time that must be allowed for the proper distribution of the collector before any attempt is made to form the coal froth. When these points have been studied it will be possible to ensure that all experiments are carried out under favourable conditions in these respects and so to draw more definite conclusions as to the suitability of this process for coal treatment in this country. "Dustproofing" Coal. For some purposes for which coal is used, the Report says the dust that is associated with slack and some graded coals is highly objectionable. This dustiness is one of the factors that is responsible for the replacement of coal by oil for certain purposes. The treatment necessary for rendering a coal (or coke) "dustproof" involves spraying it with a small proportion of an agent, generally a non-drying liquid, such as oil, oil-emulsion or calcium chloride solution, which spreads as a film on the coal surfaces and fixes the dust by surface tension. The advantage of dustproofed coal for minimising the dust nuisance is now widely admitted, but recently there has been a further interest in the process on account of other advantages that have been claimed. For example, it is claimed that dustproofed coal has shown less degradation during storage and shipment, has been less liable to spontaneous ignition, has shown less tendency to segregate in bunkers, has given a smaller quantity of a more crumbly clinker, fewer "fliers," and a higher thermal efficiency when used for boiler firing. When oil is used for dustproofing, the coal is said to be improved as regards ease of feeding and ignition in underfeed stokers, and to have a preservative effect on metal parts of the installation with which it comes in contact. It appears that a more fundamental knowledge of the process is required before it can be applied scientifically in this country. The details of the process worked out for American conditions are not necessarily suitable here owing to several important differences in conditions in the two countries. In particular it is not known which of the coals mined in this country are amenable to dustproofing, and which of the oils and other available dustproofing agents are most suitable under prevailing conditions. Experiments are therefore being carried out on these and other aspects of the dustproofing process. It appears useful to classify coals for dustproofing purposes as follows: (a) High carbon coals, containing more than about 83 per cent. carbon on a dry ash-free basis. These coals, when tested, required up to about 1 gallon of oil per ton or 5 gallons of 20 per cent. calcium chloride solution for adequate dustproofing. (b) Low carbon coals. For these coals the amount of the agent necessary for dustproofing increased sharply as the carbon content fell below 83 per cent. Normally the effects of dustproofing would be expected to last for several weeks or months, and in such circumstances it is probable that tars and tar oils would not be very satisfactory, It is possible, however, that if the claims for dustproofing are substantiated there may be uses for dustproofing where a lesser degree for permanence would be adequate. Several possible applications of transient dustproofing will readily come to mind, but the following may be given as examples: (1) Dustproofing of coal prior to carbonisation to minimise segregation and losses of fines, and perhaps to give coke of a more uniform texture. (2) Dustproofing at the colliery to reduce the dust nuisance and so facilitate the control and adjustment of coal preparation plant such as breakers and screens. (3) Dustproofing applied to coal or dust in certain types of dry-cleaning plant, which have a dust problem. In these instances it is possible that small quantities of tars or tar oils could be used. The difference between various coals both in the amount of the agent required for dustproofing and in the permanence of the effect obtained is believed to be due largely to the internal surfaces or porosity of the coals.
Report of the Fuel Research Board for the year ended March 31, 1937. H.M. Stationery Office. Price 3s. 6d. net.
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||