6th November 1937, Page: 129, Column: 1
Wire Ropes
The following brief notes are extracted from the paper on
"Modern Practice in the Manufacture of Wire Ropes," by
Mr. J. L. Kerry, which is presented in full in THE JOURNAL of the
Leeds University Mining Society.
In practice, the manufacture of wire ropes for the mining
industries seems to classify itself under the following headings
(1) Haulage ropes; (2) Winding ropes; (3) Guides, rubbers and
balance ropes; (4) Coal-cutter, jig and other auxiliary ropes.
The demands of the colliery trade are exacting, and are also
intensifying. An increased rate of output has induced heavier
haulage and winding loads and higher winding speeds. Modern
practice in rope-making has been concentrated in meeting these
needs, and progress in rope-making practice has only been obtained
by constant and intensive experiment and research.
Mining ropes are manufactured from the following grades of
steel :—
Basic Steel. — This is in common use for haulage ropes, balance
ropes, guides and conductors.
Acid Steel. — This is a reliable material of great ductility, made
from the highest grade of ores, and is used for haulage and winding
ropes working under conditions which call for resistance to heavy
frictional wear, shock, vibration and fatigue.
Special Acid Steel. — This is the highest grade made by the same
process as acid steel from specially selected raw material. It is
a grade which may be used when a high tensile stress is required
coupled with toughness and ductility.
Regarding the construction of wire ropes, the two main classifications
are: (a) the stranded type; (b) the solid type.
In the stranded type the ropes are made up of a number of
strands twisted specially around a main core. Each strand
consists of a number of single wires wound round a strand core
and the core may consist of fibre, a single wire or a combination
of wires.
Included in the solid type of rope are locked coil ropes of all
types and ropes of spiral construction. No stranding takes place
in the manufacture of a locked coil rope, which is produced by
placing concentric layers of single wires round a wire core and
adding a final cover of one or two layers of interlocking wires.
Spiral ropes such as are used for standing ropes on aerial ropeways
are made on the same principle, but the final layers of
interlocking wires are omitted.
The actual construction of a stranded rope is carried out in
three operations.
(1) Winding. — The wire from which the rope is to be made
is first wound from coils on to bobbins by machinery especially
adapted to this purpose. The full bobbins are transferred to
the stranding machine.
(2) Stranding. — This process results in the wires being twisted
into strands which are wound on to larger bobbins. These bobbins
are then placed in another machine known as the closer.
(3) Closing. — The final operation, during which the strands
are twisted over a centre core of manila or other material into
the finished rope. This in itself is coiled on to a collapsible drum
if delivery is required in a coil, or the rope can be coiled on to a
wooden drum if desired.
The manufacture of stranded rope is practically the same
process as that of making a single strand. Strands in the rope
replace wires in the strand. The first end of the rope is given
several turns round a heavy winding-off drum and thence to the
take-up reel. The hemp core is led through the centre tube from
the back of the machine, through which are termed the "nips,"
and then covered by the strands.
The length of lay employed in manufacturing the strand or
rope is adjusted by a-number of gear wheels which can be altered
by the operator to give any lay which is required.
In the manufacture of flattened strand ropes, the strands are
first made triangular by using either a solid triangular wire or
a number of round wires in triangular formation in the centre of
each strand. These shaped-strands are then put into the closer
and rollers keep them in correct position for closing.
The use of a metallic covering on the wires has been considerably
developed. At one time the use of a coating of zinc on wire for
rope making was deprecated, as during the process of applying
the spelter the physical properties of the wire were likely to be
impaired. This drawback has now been overcome and steel wire
can now be made with a heavy and regular coating of protective
spelter, and with the wire retaining all its original properties.
This is a development of great importance, and the application
of the rust-resisting principle to wire for rope-making is a considerable
step towards the elimination of internal corrosion.
By this method the metallic coating is applied to the wire at an
early stage of manufacture. By the process of drawing, the
spelter is not removed as might be supposed, but becomes incorporated
in the skin of the wire. The result is that even when
the external wires of a rope of rust-resisting material becomes
slightly worn, a thin protective cover is still available to resist
corrosion. Moreover, these wires, situated in the centre of a
strand which cannot be observed, and to which lubrication can
hardly penetrate, are not attacked by corrosion and the quality
is preserved.
Another recent development is the introduction of the pre-formed
or tru-lay type of rope. By a process of manufacture
the strands and wire are pre-formed to the exact helix which they
take up in the rope. There is therefore no tendency for the rope
to spring when cut. In the manufacture of ordinary rope the
wires are forcibly held in position throughout the life of the rope,
as can be seen by cutting such a rope at any point when the strand
and wires will immediately fly apart. This is eliminated in a
pre-formed rope, and the wires and strand lie naturally in their
true position free from internal stress. In consequence the pre-formed
rope is better able to withstand fatigue, and as a result
a longer life can be expected.
To withstand, therefore, the arduous conditions to which a
haulage rope is subjected, a rope made on the flattened strand
principle, each strand containing a plaited wire core, all the
wires made on the rust-resisting principle, and the rope pre-formed
on the tm-lay principle, is most likely to give the best results in
service.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Kerry, J. L. | | | |