25th September 1937, Page: 90, Column: 1
Coke Properties
At the autumn meeting of the Iron and Steel Institute a paper
was submitted by H. E. Blayden, W. Noble and
Professor H. L. Riley on "The Influence of Carbonising Conditions on Coke
Properties. Part I. : Mechanical Pressure." It is generally
considered that the mechanical pressures developed in the plastic
zone during the coking of coal play an important part in the
agglomeration of binding phenomena which are characteristic
features of coke formation. Several investigators have studied
the magnitude of the pressures developed, chiefly on the basis
of laboratory experiments. Mott, for example, found that
pressures of about 800 lb. per square inch were necessary to inhibit
the swelling of a uniformly heated column of particles of a coking
coal. According to Koppers and Jenkner, the pressure exerted
on the oven walls by the expansion of the coal charge is considerably
less than that observed in small-scale tests, and is
markedly influenced by the bulk density and moisture content
of the coal charge, by the shrinkage of the coke formed and by
the characteristics of the oven.
Two Northumberland "non-coking", coals were carbonised
under mechanical pressures ranging from 0.2 to 20 lb. per square
inch, and the effect of coal size was studied with one of these coals.
The relative strengths of the cokes prepared were measured by a
new apparatus devised for this purpose. The indices obtained
show remarkably close correlation with other physical and
chemical properties. Increase in carbonisation pressure produced
a pronounced increase in the strength of the resultant coke. In
certain cases the strength index of the coke was raised from zero
to that given by metallurgical cokes. The effect of pressure on
coke strength is shown to depend on the coal size and grading.
The coke strength decreased with decrease in size at low pressures
and increased with decrease in size at higher pressures, with the
coal examined.
In their discussion and conclusions the Authors say that the
coke obtained under the highest pressure was comparable in
strength to an average metallurgical coke. It is now generally
accepted that coke formation is dependent on the assumption of
some degree of softening or fluidity of the coal particles during
coking. With good coking coals this softening effect is appreciable
even at slow rates of heating and may persist over 100-150° in
the region of 400°C. During coke formation the softened coal
particles tend to cohere or to coalesce into a plastic mass, in which
the individual particles become more or less merged. The
"binding" or "cementing" action thus initiated is completed
by the solidification of the material, as carbonisation proceeds,
into a continuous but porous coke structure. Pressure has a
pronounced influence on the binding action, partly as a result
of the deformation of the particles and the increased area of
contact produced. In the case of coking coals, adequate pressures
are usually produced by the generation of gaseous decomposition
products in the plastic coal, and in practice the pressures are also
influenced by other factors, such as the rate of heating and the
density of packing of the particles, as well as the nature of the coal.
Poorly-coking coals, on the other hand, do not readily soften
at slow rates of heating, and the temperature range of plasticity is
relatively narrow. The fluidity tends to be increased with high
rates of heating, but at slow rates of approximately 10 per minute
it is insufficient, with some coals, to bring about cohesion of the
particles except under the influence of pressure, which the carbonisation
process itself is not able to provide. The maximum binding
effects of the transient softening of the poorly-coking coals at
slow rates of heating are thus only obtained by the application of
pressure.
The observed increase in strength with increase of applied
coking pressure thus appears to be attributable in part to the
improved agglomerating or binding effect under these conditions.
Secondary effects were also evident at high applied pressures,
when the swelling induced by the entrapped gases caused increased
porosity and associated thinning of the cell walls, with consequent
weakening of the material.
It is possible that, at the relatively high mechanical pressures
employed, the cracking of the hydrocarbon vapours produced
under pressure during the plastic state may also have influenced
the strength of the cokes by inducing greater binding effects.
The relative importance of this factor is, however, difficult to
assess, but it may have a bearing on the increased strength of the
cokes prepared from the finely crushed coal and on the observed
correlation between the electrical conductivity, wet oxidation
rates and porosities.
An interesting feature of the results, the Authors conclude,
is the remarkably close correlation between the results of the micro-strength
tests and the other experimental data. It indicates that
the strength indices have a fundamental significance in relation
to the mechanical strength of the coke substance. The new test
should therefore serve a useful purpose in providing data supplementary
to those given by existing tests such as shatter and
abrasion tests.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Blayden, H. E. | | | |
| Jenkner, — | | | |
| Koppers, — | | | |
| Noble, W. | | | |
| Riley, H. L., Prof. | | | |