13th March 1937, Page: 276, Column: 1
Mine Ventilation
By H. J. Wroe, M.I.M.E., Manager, Priors Lee Colliery.
From paper read at a meeting of Shropshire Deputies at the
Walker Technical College, Continued from page 267.
Keeping Goaves Clear.
With regard to the coursing of the air along the face, the chief
object is to dilute and carry away the gas given off from the newly
cut coal, and to keep the goaves clear. The object of keeping
the goaves clear is two-fold. Firstly, the danger of a sudden
out-rush of gas due to a heavy fall in the goaf is prevented; and
secondly, the danger of shot-firing along the face is materially
reduced.
In order to keep the goaves clear of gas canvas sheets must be
fixed and maintained at intervals along the face. There is no
necessity for making these sheets in any sense tight. They should
be arranged so as merely to deflect the air, and should create little
or no obstruction to its free passage along the face. The question
may reasonably be asked, "How can the comparatively small
volume of air carried into an extensive goaf keep the goaf clear?"
It is perfectly true that owing to the large areas of the goaves
the current of air we are able to deflect into them is so far reduced
in velocity as to be incapable of penetrating very far. At the
same time some small current of air will be deflected into the goaf,
and it will dilute and carry off any gas that may move into its
path. Moreover, at the contact plane between the gas and the
air diffusion will take place, and even if we do not sweep out the
far recesses of the goaves we certainly aid the action of diffusion
by constantly providing fresh supplies of air, and in this way we
keep the goaf edges free from gas.
Coursing Air into Fast Ends.
An important point in connection with face ventilation is the
coursing of the air into fast ends. It happens, not infrequently,
that while the general arrangements for ventilating the working
face are all that could be desired, no steps are taken to course the
air into fast ends. It is essential that fast ends should be ventilated
— especially where coal-cutters are employed. In a circular
letter issued a few years ago the Chief Inspector of Mines said :
"In several instances, the working of coal-cutting machines in
fast ends of longwall faces where ventilation was either quite
inadequate, or totally absent, has resulted in explosions of firedamp,
not only in seams which were admittedly fiery, but also in seams
which, prior to the accident, had been considered comparatively
free from firedamp. I disapprove of reliance being placed upon
'leakage through the pack,' or similar expedients. Good ventilation
is always necessary, and doubly so on machine faces."
Ventilation of Narrow Headings.
Now with regard to the ventilation of narrow headings, whether
in coal or rock, the usual practice is to divide the heading by a
partition of canvas brattice. A better means of conducting a
current of air to the heading face is by a range of sheet-iron air-pipes.
Air-pipes should be of ample size. We frequently find
the area of the pipe far too small, with the result that, if the air
pressure at the place is low, the heading is badly ventilated. This
can be avoided by providing air-pipes of adequate size.
The air should be caused to blow into the heading. It will
then be directed with greater force against the face, and will sweep
the entire end of the heading. If the air is carried forward along
the wide heading and the pipes used as the return, it will be found
that the velocity of the intake current is so low, and the ventilating
effect beyond the mouth of the pipe so feeble, as to leave the
heading face practically unventilated.
Where possible air-pipes should not be laid on the floor, where
they are liable to be damaged or deranged by falling rock or
derailed tubs.
Air-pipes are provided with spigot and faucet ends, and lugs
should be fitted for bolting them together. In a long range, the
cumulative effect of leakage at the joints may become so great
that very little air will reach the face of the heading. Leaks at
pipe joints can be materially reduced by fitting a flannel collar
to the spigot ends of the pipes before bolting them together.
It frequently happens that, owing to the length of the pipe
range, to the low air pressure available, or to both, the ventilation
of a heading by means of air-pipes presents a difficult problem.
The difficulty may be overcome in various ways: (1) By installing
an additional range of pipes. (2) By replacing the pipes in use
by larger ones. (3) By making use of a jet of compressed air — if
compressed air is available. (4) By installing a blowing fan.
(5) By dividing the heading unequally by a brick brattice.
The arrangement for using compressed air consists of a small
compressed air-pipe fitted with a nozzle, pointing along the
ventilating pipe and held in a central position by a wrought-iron
carrier. If a jet of compressed air is allowed to blow through the
nozzle, the volume of air entering the air-pipe will be found to
have increased considerably, owing to the action of the compressed
air flowing through the nozzle. The volume of compressed air
used is small in comparison with the increased volume induced
to pass through the ventilating range.
Where compressed air is used for operating hammer drills,
the air tap near the heading face is frequently allowed to remain
partly open when the drills are not in use, with the object of
assisting the ventilation and cooling the atmosphere at the heading
end. This arrangement is both wasteful and inefficient. The
method I have outlined is much more effective.
There are special cases where headings call for an exhaust
system of ventilation. For example, where there are blowers
of gas at the heading face it would be an advantage (where it could
be done) to pass gas-charged air through the air-pipe range into
the return airway. The intake air would be collared up by a door
fixed near the heading face and blown into the back of the heading
through a short range of pipes, while a second range would carry
off the return air.
Systems of Coursing Air.
There are two principal methods of coursing the air, known
respectively as the continuous-current and split-current systems.
In the continuous-current system the mine is ventilated by a
single air-current which passes along the intake airway, through
the workings, and thence by way of the return airway to the
upcast shaft. In this system the return air from one district of
the mine passes directly into another district, and from that into
another, and so on through the mine. Consequently the districts
last coursed are ventilated with impure air. If gas is given off
in one section of the workings it is carried through all the other
workings situated between that point and the upcast shaft.
In the split-current system the main air-current is divided, as
near the downcast shaft as possible, into a number of smaller
currents, each of which is confined to a particular section of the
mine known as a ventilating district or split. Each split has an
independent intake and return. The separate ventilating
districts are self-contained, and are largely independent of each
other. Apart from the advantage of providing fresh air to each
ventilating district a larger total quantity of air can be circulated
than in the continuous-current system, without increasing the
ventilating pressure.
If 20,000 cubic feet of air circulate through an airway with a
water-gauge of 1 inch, 40,000 cubic feet can be circulated without
increasing the water-gauge by providing a precisely similar airway
and splitting the air between the two airways. The power necessary
to circulate 20,000 cubic feet through each of the two airways
will, of course, be twice that required for the single airway because,
although there is no increase in pressure, there is a double quantity
of air to be dealt with.
As you are no doubt aware, there is a limit to the splitting of
the air. It cannot be carried on indefinitely. The limit of
splitting is determined by the velocity of the air at the working
face. The velocity must be sufficient to remove the gas generated,
while the volume, must be sufficient to dilute it to the desired degree.
The sizes of the ventilating districts into which a mine is divided
will vary, often considerably, and the shorter split will naturally
rob the longer one.
(To be concluded.)
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Wroe, H. J. | | | |