|
13th February 1937, Page: 244, Column: 1 Support Of Roof And SidesThese notes are based on the Mines Inspectors' Reports for 1935. The price of each Report is 1s. net. Copies are obtainable through H.M. Stationery Office. Falls of Side. Mr. J. R. Felton of the North Midland Division, is concerned about the accidents occurring at the working face, 118 being the result of falls of roof and 102 due to falls of side. He urges that special attention should be given to the reduction of accidents at the face. Consideration of the 102 accidents from falls of side at the face during the year indicates that the problem has some relation to the thickness of the seams being worked, the risk of an accident resulting from a fall of coal naturally being greater in a thick seam than in a thin one, and especially is this the case under mechanical mining. Some of the steps necessary to bring about a reduction of such accidents are given by Mr. Felton as follows :— (1) No overhanging coal or clod should be left unsupported (especially at loose-ends) unless it is being got down. (2) More attention should be given to the setting of sprags, both in hand-holing and machine-cutting: in all cases the maximum distance should, Mr. Felton thinks, be fixed at five feet instead of six feet, as is at present the almost universal practice. In hand-holing at least two sprags (one on each side of the holer) should be set before holing is commenced, and when holing is done by machine the sprags ("nogs") should be set as soon as possible after the machine has passed. (3) When an attempt to get down holed or overhanging coal has failed, great care should be taken to replace the sprags before any further work is done at the face or any person allowed to pass, and too many sprags should not be removed at one time. (4) Where the seam is 4½ feet or more in thickness or is worked to the rise at more than 1 in 12, the face should (in addition to to short sprags) be supported by long sprags, stretchers, cocker-megs or other similar means and the sprags should be stamped into the floor. (5) It is usually safer to work coal off from a buttock than by being in front, and when pulling off rates of coal a ringer or bar is often preferable to a pick as the workman can thereby stand clear of falling coal. Frequently in pulling coal men are trapped when a larger fall than was anticipated comes off from the face. Where the face is inclined, coal should be pulled from the rise side wherever possible. (6) When getting coal care should be taken to preserve a safe retreat-tools, loose coal or timber should not be left in the way-and unstable footing should be avoided. (7) At one colliery in the North Midland Division it is part of the duty of the contractors at the commencement of the shift to go along the faces and see that all loose coal is pulled off before the conveyors are started and the work of filling begins; this has conduced to safety and is good practice. As regards falls of roof at the working face, the importance of good packs (adequate in size and quality and erected as early and as close to the face as possible), and of the systematic use of bars or straps wherever practicable has repeatedly been stressed, but the value of such supports does not appear to be yet fully appreciated judging from the fact that they are not adopted as they ought to be. The number of accidents which occur between the last setting and the face suggests the need for more timely support of the roof in this area. Catch props should in all cases be set as soon as there is room in front of the main settings, and a maximum distance should be specified in the Timbering Rules for such temporary supports. Pointing to an increase in the number of accidents from falls of side, and their very serious consequences as measured by the proportion which proved fatal, Mr. W. J. Charlton of the North Western Division says they cause him great concern. As to the accidents occurring in or near the wastes, they happened generally while supports were being withdrawn, or material being obtained to build packs. The wider the wastes the greater is this danger, and the Inspector commends those managers who have not fallen to the temptation of introducing the risk of wide wastes to their working faces. One source of danger in the wastes is the practice of weakening props by making saw cuts in them to enable them to be broken by a Sylvester. This highly dangerous procedure is quite unnecessary, since appliances are readily procurable which enable practically any prop to be withdrawn from a safe distance. Mr. Charlton commends the practice prevailing at some collieries of providing two chains for each Sylvester, so that a chain may be attached to the prop next in turn to the one being withdrawn. Machine Mining Problems. The introduction of machine mining continues to make headway; the use of face conveyors being ever on the increase, The use of machinery at the coal face is invariably bound up with the correct and adequate support of the roof, both at the working face and behind it. So far as the working face is concerned, Mr. J. Macleod Carey of the Cardiff and Forest of Dean Division says considerably greater attention is being devoted to the adequate support of the root in that area than was formerly the case. The timber or steel roof supports are now set with much more regularity, and at a large number of collieries steel flats have been introduced as a further protection. New methods invariably produce new problems, and one such problem is the support of the roof at that area where the conveyor dumps its load on to the trunk conveyor. Such places should receive special attention, and especially at the ripping lip, which should be strongly supported. Steel Supports on Roads. Commenting on the recognised value of steel arches for road supports Mr. T. Ashley (Swansea) says that more attention is now being paid to tying the arches together, and in some instances the advantage of steel sheets instead of wood lags is realised. Where roads lined with steel arches are subject to settlement it is found that the refuge holes are difficult to maintain to the required width because of the distortion of the arches. This can be overcome either by setting two steel arches strapped together with short distance pieces between them on each side of the refuge hole, or by inserting a small arch three feet wide and six feet high between the arches to form the entrance to the refuge hole. Steel arches are seldom used in the subsiding area near the coal face, managers apparently preferring to use timber supports in this area and to defer the erection of the steel arches until after settlement has taken place. Stilts fitted to the feet of the arches, which are largely used in other coalfields, would overcome the distortion to the arches in the subsiding area.
|
|||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||