|
26th September 1936, Page: 81, Column: 1 Research WorkNotes from 14th annual report of the Safety in Mines Research Board (2s. net, H.M. Stationery Office) See also pages 65 and 66 in last issue. Illumination at Coal Face. An experimental face lighting equipment has been in use since April, 1934, at the Steetley Colliery of the Shireoaks Colliery Co., Ltd. The experiment was made on a double unit conveyor face 260 yards long worked from a central loader gate. The seam is the Top Hard seam of Nottinghamshire, and at this pit is 4 feet 2 inches thick. The normal method of working is to undercut 5½ feet on the afternoon shift and to strip and load during the day shift. It has been shown that, under these conditions, the installation and maintenance of coal face lighting by 110-volt incandescent lamps is simple. The equipment has proved robust, reliable and economical in use and the average life of the lamps has been 930 hours. From the statistics, the face lighting appears to have caused a reduction in the number of accidents at the face, the accidents recorded being only those affecting the 100 men who work at the face. Whilst it has often been urged that such increased illumination at the coal face as can be obtained by lighting from the mains would give greater safety, this is, the Board believes, the first occasion on which evidence in support of this claim has been advanced. Photometric surveys have been made at the coal face and it is observed that in this experiment the lamps were spaced nine yards apart. They were 60-watt lamps, and the question arises as to whether they could be replaced with advantage by, say, 40-watt lamps six yards apart, or 30-watt lamps 4½ yards apart; each of these arrangements averaging the same wattage per yard of coal face. The increased number of lamps required would doubtless increase any difficulties of manipulation and maintenance, but the greater uniformity of the illumination might be well worth the extra trouble. The local conditions may determine which is the most advantageous arrangement at any particular face. Mining Explosives. The members of the Board are informed that the substitution of "sheathed" cartridges of mining explosives for the ordinary permitted explosives is rapidly increasing throughout the country. They believe that their use provides a high degree of safety during shot-firing for reasons that will be apparent if the principal information available regarding the behaviour of mining explosives when they are fired is briefly summarised, as follows :— The safety of a permitted mining explosive depends essentially on the conditions under which it is used. An explosive is tested under rigorous conditions before it is placed on the Permitted List, but the conditions of test are not so rigorous as the conditions of use may sometimes be. In particular, a small charge of a permitted explosive can ignite firedamp if it is detonated in direct contact with an explosive mixture. This condition may arise in practice if the shot-hole crosses a break in the strata. The quantity of explosive required to do a given amount of work is least the more firmly the stemming holds in the shot-hole, the optimum condition being when the stemming remains undisturbed until the work of the explosive is fully completed. An efficient stemming material can be compounded of moist clay and coarse sand; moist clay alone is frequently inefficient. A charge in a shot-hole should preferably consist of one cartridge, e.g., an 8-oz. charge should consist of one 8 oz. cartridge rather than of four 2 oz. or two 4 oz. cartridges, for the reason that an air-gap, or, worse, a layer of dust, between cartridges may provide sufficient impediment to the transmission of detonation to cause a part of the charge to remain undetonated. It does not seem possible to cause the ignition of firedamp by a blown-out shot of a permitted explosive, provided that the shot-hole contained some stemming. It is probable that a heavily overcharged shot would cause ignition if the rock began to break down in such a way as to expose the charge before the whole of it had detonated. Under such conditions, an explosive mixture of firedamp and air might come into direct contact with detonating explosive. The danger of an overcharged shot and the greater danger of a shot in a break can be considerably reduced, perhaps removed entirely, by the use of sheathed explosives. A sheathed explosive, as produced commercially, is a cartridge of a permitted explosive surrounded by a thin layer of sodium bicarbonate. This salt (One of many tested in an attempt to provide an inhibitor of the ignition of firedamp by explosives) apparently yields a protective blanket of steam and carbon dioxide, during the detonation of the explosive, which shields it from firedamp. As a result, an 8-oz. cartridge of a sheathed explosive when freely suspended in the most explosive mixture of firedamp and air can be fired without igniting the mixture. In experimental work, none of the permitted explosives, sheathed or unsheathed, has been found capable of igniting coal dust when the maximum allowable charge has been fired unstemmed from a steel mortar. The action of the sheathing material for explosives at present used commercially (sodium bicarbonate) appears to be, in a sense, mechanical. A preferable material would be one which exerted a specific inhibition of the ignition of methane. It would be preferable also if a coherent coating could take the place of a layer of a powder. Ignition by Electric Arcs. The rapid development of machine mining at longwall faces is giving rise to some anxiety on account of the large amounts of coal dust produced at and near the face, often in association with electrically operated machinery. In particular, dense clouds of dust may often be seen at the loading points of conveyors. Suitable protection by stone-dusting at the face is usually difficult. The questions arise, therefore, as to (1) what is the minimum concentration of coal dust in the air which can be ignited electrically, and (2) what is the minimum energy of an electric discharge which can ignite coal dust. Experiments on this subject by Thornton and Bowden showed that it is possible to ignite coal dust clouds in air directly by electric arcs. The Board has put in hand experiments directed primarily towards obtaining a measure of arc energy and dust concentration limits for ignition. The results obtained so far may be described as follows :— The tests were made in a vertical cylinder 4 feet in diameter and 10 feet in height. A cloud was made by firing a detonator in a bag of dust at the top of the chamber. The arc was struck during a predetermined period between copper electrodes which were separated by a inch gap, the arc being horizontal and on the axis of the explosion chamber. The coal dust was ground so that 85 per cent. passed through a 200 mesh sieve. Most experiments have been made with Silkstone coal dust and it has been found that as the concentration of the dust in the air is raised from about 0.037 oz. to 0.080 oz. per cubic foot the ease of ignition by an electric arc increases. When there was only 0.037 oz. per cubic foot the flame that was produced did not spread far from the arc. The arcs used were struck on a 500-volt D.C. system and sufficient ballasting resistance was put in circuit to limit the current to 17, 33, 50 or 64 amperes as desired. The duration of the arc was varied between 0.1 and 1.0 sec. When the concentration of dust was 0.08oz. per cubic foot, ignition was obtained with any of the currents used with an arc duration of 0.1 sec. Work on Coal Measure Strata. Laboratory work on the properties of coal measure rocks has been mainly concerned with their behaviour in compression. The lateral and vertical deformations of cylindrical rock samples under loads applied at right angles to the "bedding" have been measured, and under these conditions the value of Poisson's ratio has been shown to increase as the stress increases. This means that the magnitude of the lateral pressure in undisturbed strata more nearly approaches that of the vertical pressure as the depth increases, and explains the relatively greater evidence of lateral pressure observed in the deeper mines. In regard to work on roof control problems by means of models the tests have been directed to a study of fracturing in the vicinity of a single roadway under different strength conditions of roof, sides and floor. In one, which had the stronger sides, an arched type of fracture developed above the roadway. The immediate roof fell and the fractures originated at the top corners where there was the greatest concentration of stress. In the other, the sides were much weaker and yielded, so preventing the high concentration of stress. These two examples help to confirm the reason advanced for the differences observed in bords and walls, viz., that the sides of the former are the stronger and are therefore more likely to cause fracture of the roof. In the Third Progress Report of the North of England Committee on Roof Fracture Control in Bords the discussion of the fracturing of shale roofs in narrow cuttings at the faces of bords suggests the significance of shear as a factor affecting the problem of falls. The value of affording a measure of relief from the initial pressure — and the additional pressure induced when mining coal — with a view to the avoidance of roof fractures and falls is also established. The results obtained have confirmed the suggested reason for the better roof conditions in walls — where the sides are weaker — than in bords. A conclusion to be drawn is that supports should not be too rigid. It is clear that a support which develops more resistance than another is carrying an undue proportion of the load. This fact is of particular importance when considering the relative qualities of roadside and intermediate packs. Further investigations in North Staffordshire on the actual movements of roofs and floors in inclined seams have confirmed the suggestion that face props should in general be set "normal." Consideration of the results of the work on ground movements in advance of longwall faces and in roadways of advancing longwalls is enlightening. These have shown that when a face stands, the extent of the fractured ground ahead is increased and the the distance behind at which roadside movement is appreciable, decreases. Because of the effect of the time factor, therefore, the distance ahead of a face at which the roof may be broken, i.e., where the forward abutment pressure is effective as regards fracturing the roof, is a decreasing function of the speed of face advance, and the more quickly a face moves forward the nearer does it approach this abutment or live pressure zone ; also, the further removed from the face is the abutment zone in the goaf. Conversely, with a slower rate of advance the "pressure arch" moves forward relative to the face. Bag Supports. Laboratory tests on bag supports — a method of support (as described by Mr. David Jeffreys before the South Wales Institute of Engineers) in which fine material such as roadway dust or washery waste is filled into bags used for building cogs and packs for supporting the roof — have shown that the resistance developed is closely dependent on the degree of filling of the individual bags. It is desirable that the individual bags should not be tightly filled, but should be sufficiently slack to allow of being well bedded down so as to afford a large flat contact with the bags above and below. An increase in the size of the bags from 14 by 33 inches to 18 by 32 inches produced a marked increase in the resistance when the bags were filled with the same weight of material. The experiments showed that a pack consisting of loose material filled between bag walls developed a resistance comparable with that of packs built with good stone walls, but the initial resistance was not so good. It was found that, by making the walls concave (battering the lower half and leaving the top half vertical), a marked increase in resistance to bulging outwards under lateral pressure from the filling was produced. It is to be anticipated that similar benefit would result from the application of this method of building to stone pack-walls. The Problem of Noise. The increasing use of machinery underground brings into prominence the noise factor as one which in certain circumstances may be a contributory cause of accidents. From the general standpoint some noises are inherent and sometimes the technical considerations present great difficulty. But in particular instances — the exhausts of pneumatic machines such as air haulage engines, picks and air driven conveyers and the operation of shaker conveyers — there are distinct possibilities of noise reduction by altering the frequency of vibrations and damping them, and by replacing loose and worn parts. Preliminary tests have been made on a compressed air turbine driving a gate belt conveyor and on the exhaust of a reciprocating air haulage engine, using as a silencing medium a flexible acoustic blanket of asbestos material. The results in the first test showed that both mechanical and exhaust sounds were effectively reduced, and in the second were particularly striking. The work is being continued.
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||