|
28th March 1936, Page: 298, Column: 2 November (1935) ExaminationsReport of Central ExaminersThe Central Examiners have issued their report on the examinations for certificates of competency as managers and under-managers of mines held in November, 1935. Their comments on the work of candidates are given below with the text of the questions, the comments being reproduced in italics. The official Question Papers, containing also the plans and diagrams, are obtainable (2s. net) through H.M. Stationery Office. Winning and Working (1st Class). (1) A seam of coal 5 feet thick, with an inclination of 1 in 4, has to be worked from shafts which have been sunk to a depth of 900 yards. Lay out the workings at a distance of 800 yards to the dip to yield about 800 tons per shift, the general method of working to be longwall. Temperature will be an important factor. (50) The question asked for workings to be laid out at a distance of 800 yards to the dip from the shaft in a seam with an inclination of 1 in 4. In many cases the setting out of road ways for this distance was ignored. The question also stated that temperature would be an important factor. It was therefore expected that greater attention would have been given to providing airtight roadways. Many candidates neglected the provision of two intake airways. The layouts in general lacked detail. (2) Coal is to be wound from an intermediate landing, or inset, in a shaft which is fitted with rope guides. Explain and sketch the arrangements you would make at the landing so as to deal expeditiously with, say, 200 tons per shift, this being one-quarter of the total output. (40) Some candidates suggested keps, which are prohibited at intermediate landings. Most other candidates did not pay sufficient attention to keeping the cage steady whilst it was being loaded. It was disappointing that more answers did not suggest hinged platforms at the lending. The sketches generally could not be commended. (3) Explain, generally, why coal seams are found at various inclinations, and also how faults have been caused. Why are overlap or reverse faults seldom met with? (40) This question was generally well answered. (4) A longwall face, where coal-cutters and conveyors are used, has a heavy roof. The depth of holing is 4 feet 6 inches and the seam is 4 feet thick. Show in detail by plan and cross-section, giving essential dimensions, how you would have the roof supported (a) when the face is ready for the coal-cutter and (b) when the face is ready for the colliers to fill. What precautions would you take in each case? (40) On the whole the plans and cross-sections were good. The great majority of the candidates would bar the face systematically, the bars being let in the top of the coal previous to the coal being cut, to be supported later by an additional prop at the face itself. Some completed their sketches by showing the roof supports for some distance away from the face. (5) During periods of severely cold weather water leaks through the joints of the tubbing in a downcast shaft. Explain, in detail, what you would do as a temporary measure to remedy this, and how you would try to stop the leakage permanently. (40) To stop the leakage temporarily during severely cold weather, some would light fires at the surface or put in steam jets, not mentioning caulking or wedging of the tubbing. For a permanent repair the cementation process was generally recommended, although details of such work were not given. A few suggested replacing the tubbing, an answer not expected. (6) State reasons for and against the firing simultaneously of two or more shots in a ripping near the longwall face. (40) This question was well understood, and the reasons for and against were explicit in most of the answers. (7) On a parallel winding drum fitted with wooden lags, there is difficulty, at the beginning of the wind, in getting the rope to coil compactly, when near the side of the drum. What measures would you take to overcome this? What are the objections to having each rope in succession traversing the same path when near the centre of the drum ? (40) There were few answers to this question. The candidates who answered it got the correct solution either by grooving out a path on the drum, or curving the lags at the sides of the drum to make an inclined plane and so induce the rope to coil correctly at the sides. The objections to the ropes crossing the centre of the drum were fairly well given. Ventilation (1st Class). (1) On the plan . . . . show how you would arrange the distribution of the air-currents, using the signs and colours given in the General Regulations. Sheets to be shown thus J. (50) Many arrangements produced were satisfactory. A considerable proportion of the candidates need to bear in mind that a small number of splits, laid out as equally as circumstances allow, give more efficient ventilation than do a larger number of splits of differing resistance. Some candidates did not use the signs prescribed in the Regulations, and some omitted the vitally important separation doors near the pit bottom. (2) Give a sketch and short description of an electric safety-lamp, enumerating the various parts, and stating the precautions that should be observed in its use. Also state the points to which attention should be paid in dealing with these lamps on the surface, to ensure their maintenance in an efficient state. (30) About half the answers were quite satisfactory — in others the knowledge of these lamps was not definite enough. (3) An engine and ventilating fan working with an overall efficiency of 66 per cent, produce a current of 100,000 cubic feet of air per minute through a mine. What water-gauge would you expect to find at the fan drift when the indicated horse-power is 100? If by increasing the speed of the fan the quantity of air is increased by 20 per cent., what would then be the water-gauge and indicated horse-power? (30) This was a favourite question, and most of the answers were excellent. The others showed ignorance of the proper relationships between quantity, speed, water-gauge, and power required. (4) A quantity of 120,000 cubic feet of air per minute passes from downcast to upcast through two splits. Split A has a sectional area of 8 feet by 10 feet and a length of 8,000 feat. Split B has a sectional area of 6 feet by 10 feet and is 6,000 feet long. What quantity of air passes along each split? (30) About 30 per cent, arrived at a correct answer. Of the others, many used rubbing surface alone in their calculations, neglecting areas altogether; and others did the reverse, both obtaining incorrect results. There were many arithmetical errors. (5) Sketch arrangements suitable for the installation of a screw (or air-propeller) type of mine-ventilating fan. What advantages are claimed for this type of ventilator? (30) A favourite question. All the candidates had some knowledge of this type of fan. Some answers were excellent; others ranged down to very poor descriptions. Several carried the motor or engine shaft across the upcast pit itself. (6) Calculate the (a) area, (b) perimeter and (c) rubbing surface of an airway 1,000 yards long, lined with steel-splayed arches 8 feet high, 8 feet wide at springings, and 9 feet 2 inches wide at floor, inside measurements, neglecting the area behind the surface of the supports. If 20,000 cubic feet of air par minute passes along this airway, calculate the ventilating pressure used, in inches of water-gauge. Assume the above roadway to extend from downcast to upcast; if another similar roadway between the same points were brought into use, the quantity of air being unaltered, what would then be the water-gauge? (30) Less than one-fourth of the answers were fairly correct. A large number were unable to calculate the area of the given airway even approximately. The same applies to the perimeter, and to the rubbing surface. The method of calculating the ventilating pressure was better known. In some cases the water-gauge was wrongly said to be greater, with two similar roads in use, than with one for the same total air-current; many did not attempt to answer this part of the question. (7) What are the properties and chemical constituents of: (A) Atmospheric air, (B) firedamp, (C) carbon monoxide, (D) blackdamp, (E) water. Distinguish between chemical combinations and mechanical mixtures in each case. (30) Most answers were fairly satisfactory, but many were wrong as to chemical combination and mechanical mixtures. General Management and Legislation (1st Class). (1) Compulsory. — Write an essay on the effect of dust on the health and safety of those employed in the underground workings of a mine. Explain the dangers and effects which may arise, the precautions specified in the Coal Mines Act, 1911, and the General Regulations, and any other precautions you would suggest. Arrange your answer under the following heads: (1) Coal dust in roads and workings; (2) fine dust in suspension in the air at conveyors and loading stations and at the working faces; (3) stone dust. (30) Many very good answers, which showed an intelligent appreciation of the subject, but some disregarded the arrangement under the heads stated in the question. (2) Make a list of the various notices and authorisations required to be officially given by the manager of a mine and state to whom they have to be given. (25) Few complete lists and many important omissions. (3) What is the meaning of "pressure" as used in the electrical Regulations ? Row are the different pressures classified? (25) The classification of the different pressures was generally correctly given, but the definitions were often rather vague. (4) Describe the provisions of the Order of 1st May, 1935, relating to the provision of firedamp detectors, and say when it came into force and for what period. State aiso under what conditions flame safety-lamps are recognised as firedamp detectors. (25) The provisions of the Order were generally well understood and expressed. (5) What alterations were made in respect of reviving apparatus kept at Central Rescue Stations and at mines by the Coal Mines (Rescue) Amending Regulations, dated 8th July, 1935, and when do they come into force ? — (25) There was some confusion as to the section applying to Rescue Stations and to mines. (6) When is a mine defined as being abandoned under the Coal Mines Act, 1911 ? State fully the requirements as to the steps to be taken on the abandonment of a mine. (25) The definition as to when a mine is abandoned was often vague, and the list of details to be shown on plans was often incomplete. [To be continued.]
|
|||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||