|
29th February 1936, Page: 268, Column: 1 Notes On Metalliferous MiningAt the January meeting of the Associates and Students' Section of the North of England Institute of Mining and Mechanical Engineers a paper was read on "Short Notes on Metalliferous Mining, with Special Reference to Tin Mining in Cornwall and Iron Ore Mining in Cumberland," by Mr. Walter Widdas, B.Sc., Assoc.I.M.E., and Mr. C. G. Widdas, B.Sc., Stud.I.M.E., in which they said they did not intend to go deeply into the geological formation of the ore deposits, but rather deal with the ores as we find them. The ores are found in flat seams, as the ironstone in Cleveland; veins or lodes as tin, lead and various forms of "spar" etc. ; irregular ore bodies as the hematite iron ore, or small particles of ore among the sand and mud of rivers and shore deposits. The methods adopted in Cleveland are similar to bord and pillar working. Ore in the form of veins or lodes is either well defined in fissures filled up with ore material, or the concentration of material in a vein form, with the concentration diminishing the further away from the vein proper. It is therefore obvious that, although ore should not be left, it is no use mining large quantities of material yielding only a very small percentage of saleable ore. This is where the official of the mine has to judge for himself just how far to go. Irregular-shaped ore bodies may be filled up cavities, but in the case of iron ore in Cumberland these bodies generally occur on or near a fault in the limestone. Solutions containing iron have found their way down the faults, and the limestone has undergone a chemical change, which has resulted in the formation of hematite (iron oxide). Mining of Tin in Cornwall. — The tin ore (Cassiterite) is found in veins in the granite country rock, and is associated with wolfram, arsinical pyrites (mundie) and very small traces of copper. A shaft is sunk on or near the lode (vein), and roadways driven from various levels to the vein. Levels are then driven into the lode itself and these are connected by whinzes and raises. When these have been driven a sufficient distance from the shaft the pillars so formed may be extracted. The Authors gave the following example to illustrate the method employed. Two levels are driven away from the shaft and these are connected by a "raise" about 40 yards to 50 yards from the shaft, the levels being from 120 to 180 feet apart, depending on the conditions prevailing. The higher level is advanced about ten yards, and at a point six yards along a whinze is put down about eighteen feet; then a level is driven back to hole in the "raise," thus leaving a pillar about twelve feet square. This lower level is advanced about two yards to enable further driving to be done later. The top corner of the pillar near the raise is now removed, and the material is allowed to fall to the bottom of the raise, where it can be loaded into cars through suitable chutes. This underhand stoping proceeds and benches are formed, usually 4' 6" deep and 4' 6" long. It can be likened to step longwall, except that it is in a vertical and not a horizontal plane. Underhand stoping is very convenient because the material is easily disposed of and ground shattered by shots in the floor, therefore reducing the danger from falls of stone. Where the side walls of the lode are poor and likely to require much timber, "overhand" stoping is employed. Here the men stand on the broken ore and the ore face is above them. Sufficient ore must be loaded from the chutes to give the men room to work, while enough must be left to enable them to reach their work. All drilling is done by compressed-air and as many as fourteen holes per shift may be drilled. All shot-firing is done during the last hour of the shift, and only one shift of drillers was employed. The ore may be drawn from different levels and the winding engine is fitted with a fast and loose drum, so that both cages can be used for any level. When the ore reaches the surface it is by no means ready for sale, and, as only about 1 per cent. of the material mined forms saleable tin ore, much work has yet to be done. We have all seen and read about coal-cleaning plants, said the Authors, but compare the most elaborate plant for coal with the following: The tin ore is taken from the shaft and tipped over a "Grizzly" screen, where, all under 2" goes straight into the bunker. The over size goes direct to a jaw crusher and is crushed to below 2". This material is then transported to the mill proper. Here the 2" under material is fed into a battery of stamps and is crushed down so that it will pass through a 14-mesh sieve. The next process is classification in an upward current classifier, and this divides the material into two parts. The coarse or sand goes to sand tables and the fines to the slime tables. The heads of all tables go to the tin yard and the tails direct to waste, but the middlings are retreated ; first they are crushed in a tube mill and then go to slime tables and Frue vanners. In the tin yards the concentrated tin ore from the mill is calcined, and this drives off the arsenic which condenses in special flues. The calcined ore is fed on to magnetic. separators where iron is first removed, and a second more powerful magnet removes the wolfram, leaving the tin to go forward. This is mixed with water and made into a thick pulp in a "kieve," and is kept well stirred until the kieve is full. The side is then struck with mechanically operated hammers, and this causes the heavier (tin containing) particles to settle first. The water is ladled off and a sample of the material is "panned." This gives the yard foreman an indication of how much material is to be removed. The lighter layer is then put into another kieve for "tossing," and the heavier is mixed with more of the heavier material and tossed. This goes en until the yard foreman is satisfied he has got nearly pure tin ore. The final product then contains about 70 per cent. of metallic tin. Iron Ore Mining in Cumberland. — The main ore body is usually proved by boreholes before any mining work is begun. After the body has been proved the shaft is sunk near it and down to a level just below the bottom of the ore. Levels are driven from the shaft to the body at predetermined distances, and these are used as loading levels. Subsidiary levels may be driven, depending on the lay-out. The following example was given to show the usual method employed: Levels are driven from the shaft at 42-foot intervals then starting at the top one a roadway six feet high is driven and pillars formed as in herd and pillar workings. When the pillars are formed the ore is extracted as in broken workings, but eight feet of roof is taken down and loaded. Each level from the shaft has therefore three subsidiary levels feeding it. The process is called "top slicing." The method has been worked successfully, starting at the bottom and filling the wastes with sand.
|
|||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||