|
28th September 1935, Page: 84, Column: 1 Safety On Advancing LongwallsImportance of Good PackingThe investigations directed by the South Wales and Monmouthshire Safety in Mines Research Committee have fully established the paramount importance of good packing from the standpoint of ensuring the minimum of ground movements following coal extraction, and maintaining good roof conditions at the face. The Committee, of which the chairman is Mr. F. Llewellyn Jacob and the engineers are Mr. L. J. Barraclough, M.Sc., M.I.Min.E., and Mr. F. I. Davies, B.Sc., M.I.Min.E., have issued two support of workings pamphlets, in the first of which it was stated that the nature and the extent of the ground movements largely depend upon the measure of support afforded, particularly by the packing. In pamphlet No. 2, from which extracts are appended, special attention is devoted to the quality of the packing. Some examples are given in the pamphlet with illustrations. Laboratory tests have shown the resistance of a pack in the early stages of compression to be almost. entirely due to the walls. To obtain effective roof control pack walls must be well built, tight to the roof, at the earliest opportunity. If the pack walls he left several inches clear of the roof, even though the interior filling of small material be packed to the roof, little resistance is offered until the interior is compressed and the roof tightens the walls; in these circumstances the roof is not under adequate control, it is broken, and convergence near the face is high. Similarly, walls built on small rubbish do not offer early resistance; they should be built on the solid floor. Packing with a high initial resistance is all-important in securing good roof control; to leave the walls clear of the roof by a few inches is wrong. Pack walls built on the solid floor and well tightened to the roof, are most effective. The building of interior walls in packing is strongly recommended, especially in the thicker seams. The inner walls are supported by the filling on either side, and cannot be pushed out. In all cases it is desirable that the packing should be built as closely as possible to the face. The roof span between the packing and the face is thus reduced to a minimum, thereby promoting safety, and the packing offers early resistance. If the building of the packing be delayed, resistance is not offered sufficiently to control adequately the roof at the face and a high rate of convergence, with a broken roof, may result. It is especially desirable on machine-cut faces to pack immediately after the face is cleared, and before cutting is commenced, as the largest roof movements occur when coal cutting. The extent of the packing is not the all-important factor in ensuring good roof conditions. With packing built of slabby sandstone very low rates of convergence have been shown to be associated, progressively higher rates having been measured when packing with irregularly bedded sandstones, strong clifts, weak clifts, coal, fireclays, clods and rashings. With weak materials such as clods, however, efficient packing has been built and good roof conditions maintained by the introduction of interior walls. Regarding the effect of seam thickness, observations have shown the strata movements to he generally greater in the thicker seams owing to the higher packs offering less resistance for a given compression. The resistance of the packing in the thicker seams can be increased by the introduction of additional interior walls ; by such means, in seams from 6' 6" to 7' thick, rates of convergence of 1 in 40, and very good roof conditions, have been maintained. It has been shown in a number of cases in the coalfield that "weights" are due to insufficient support, and that providing the requisite attention is paid to the packing they do not occur. General Conclusions. For given material the resistance developed by packing and hence the condition of the roof at the working face, depends upon the quality of the walls and the tightness of the interior filling which gives them stability. Interior walls increase the strength of the packing and reduce convergence. More interior walls are necessary in the thicker seams. Walls left clear of the roof by a few inches, or not built on the solid floor, are not efficient. It is important that the packing be built as closely as possible to the face. The stronger the packing material the more resistant the pack. The quality of the packing is of greater importance than the quantity in so far as the roof condition is concerned. In all the cases investigated, bad roof conditions, and generally frequent "weights," have been found to be associated with bad packing, and the adoption of better systems of packing, involving packs of good quality, has resulted in good conditions and freedom from "weights." The maintenance of good roof conditions, and the elimination of "weights" with their frequently concomitant blowers of gas, are important factors in safe working, but the undesirability of leaving spaces in the wastes in which gas may collect should not be overlooked. Moreover, when roof conditions are good, the setting of temporary supports should not be neglected.
|
|||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||