|
6th August 1932, Page: 19, Column: 1 Examination QuestionsSurveyors' Certificate.*Morning Session. — 1. The plan on separate sheet is part of a Geological Map, with a general section showing the relative positions of the seams whose outcrops are indicated on the plan. The bore shown on the plan has proved two seams at the depths stated, and it. is proposed to deepen it to prove the seams in the strata below the Millstone Grit. A deep bore about a mile distant has proved the Dunfermline Splint Coal — the deepest workable seam in the Carboniferous Limestone measures — to be 450 fathoms below the Castlecary Limestone. Draw on your Answer Book a section of the strata on the line AB shown on the plan, and find the approximate depth at which the bore shown on the plan will reach the Dunfermline Splint Coal. Assume that the thickness of strata between that seam and the Castlecary Limestone is as above stated, that the hade of the fault, the conjectural line of which is shown on the plan, is 450, and that the alluvium overlying the rockhead is 30 feet in thickness. (14) 2. A pentagonal pyramid — axis 4 inches and edge of base 2 inches — rests with its base on the horizontal plane, and one edge of the base perpendicular to the vertical plane. It is cut by a plane inclined 300 to the horizontal, passing through the edge of the base which is at right angles to the vertical plane. Draw the plan and true shape of the section. (12) 3. The sum of the perimeters of two square plots of land is 1,056 feet, and the sum of their areas is 3,904 square yards. What is the length of their sides ? (10) 4. A square chimney has been heightened by adding a section of brickwork with vertical sides, the extent of which cannot be ascertained by direct measurement Observations taken with a theodolite to a corner C, at the bottom of the added brickwork, from two points A and B, 100 feet apart on level ground, gave the following: Angle CAB 60°31' angle ABC 82°15' Angles of elevation to C and D, the bottom and top respectively of the new brickwork, are as follows :— From A: 26°50' and 32°12'. From B : 30°01' and 35°42' Calculate to the nearest inch the height of the brickwork added to the chimney. (8) 5. State in what respect the extensive use in mines of steel props nt the face and steel arches in the roadways may have affected the work of the Surveyor. Describe briefly what special steps, if any, yon would take under the above conditions to ensure accurate correlation of the underground workings with the surface lines. (8) Afternoon Session. — 1. Compulsory Question. Undernoted are given the details of a theodolite traverse of part of a roadway in a mine. It is proposed to improve transport facilities by driving from a point H on the line FG a stone drift dipping 1 in 4 on the bearing BA to connect, with another roadway to be driven from point B on the same bearing and inclination as AB. Calculate the distance from the point F at which the stone drift must be set away, and how far it. will require to be driven before it meets AB produced.
(14) 2. A large debris heap has been laid down on level ground in the form of a truncated cone. It is 300 feet in diameter at the base, and the top is 50 feet higher than the base. It is proposed to drive two cuttings through the centre of the heap at right angles to each other, with their formation level on the ground. Draw a plan of the heap and cuttings on a scale of 50 feet to an inch, and calculate the volume of material left in the heap when the cuttings have been completed . Assume the angle of repose of the material to be 400, and that the cuttings are 50 feet in width at ground level. (12) 3. A roadway driven on the line of full dip in a seam dipping 1 in 7 is intersected by a downthrow fault of 25 feet, bearing at right angles to the line of the road, with a hade of 36 inches vertical to 19 inches horizontal. Calculate, without the aid of mathematical tables, the length of a stone drift, dipping 1 in 4 on the same bearing as the roadway, to win the seam on the dip side of the fault, and state at, what distance back from the fault you would set away the drift so that the seam on the dip side of the fault may be won at a point 10 yards beyond it. Assume that there is no change beyond the fault in either the direction or rate of dip of the strata. (8)
4. Establish the formula 5. A circular shaft 20 feet in diameter is plumbed and found to be 4 feet out of vertical at the bottom. Calculate the area in square feet of the crescent-shaped portion at the bottom of the shaft which is outside of the circumference from the true centre at the surface. (10) 6. Calculate the length in inches on the Ordnance Survey Maps drawn to scale of and respectively of the side of a square equal in area to 4 acres in each instance. The co-ordinates, in feet, of the centre of a colliery shaft relatively to the south-east corner of 6-inch Ordnance Survey Sheet VIII. are N.7960 and W.11580. The Ordnance Survey Sheet to scale of showing the buildings immediately adjoining the shaft is required. Give the number of the required sheet. (8) * Questions set at Examinations in May, 1932. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Complete sets of questions available through H.M. Stationery Office. 1s. 6d. net.
|
|||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||