|
6th February 1932, Page: 229, Column: 1 Examination QuestionsFirst Class (Mine Managers).*1. — WINNING AND WORKING. 1. Under what conditions would you consider the "longwall retreating" system of working the most suitable? Sketch a layout on this system sufficient to yield about 500 tons per shift from a 5 ft. seam, dipping 1 in 8, and give principal dimensions. (50) 2. Make a sketch of a curve on a main-and-tail haulage road, where the road changes direction some 30 degrees. The tubs are 3 ft. wide and the gauge is 2 ft. Show the track with guard or check rail and the rollers for the ropes, and give main dimensions. (40) 3. In working a seam of coal on the longwall system what observations would you make if instructed to report on subsidence of the overlying strata? Row would the subsidence be affected: (a) In the case of the coal measures coming right to the surface? (b) Where the measures are covered by sand or clay? (40) 4. How would you open out and develop a 4 ft. 6 in. seam of coal, which dips at 60 degrees to the horizontal? Show, by sketches, the timbering of a face and of a level haulage road. (40) 5. Make a rough line sketch of a headgear, showing the compulsory safety appliances, and either sketch or describe any extra safety devices you would introduce. (40) 6. Describe in detail, and in due order, the process of preparing for, and firing, a shot at the coal face. What dangers have to be guarded against? Row many shots in a shift would you consider the maximum for one man to fire on a longwall face in a level seam 4 ft. 6 in. thick? (40) 7. Discuss the advantages and disadvantages of the various well-known types of steel props. (40) 2. — THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine, which accompanies this paper, show how you would ventilate the working places. Mark the direction of each air-current; also indicate clearly the position of air-crossings, doors, stoppings, regulators, and sheets; using the signs laid down in the Regulations. Sheets to be shown thus S (50) 2. Give the properties and composition of gases usually met with in mines. State what you know about the diffusion of gases. (30) 3. A fan produces 200,000 cubic feet of air per minute in a mine with a water-gauge of 3 inches. Assume an efficiency of 65 per cent, in the fan and motor and calculate what energy is being supplied to the motor expressed in horse-power. If this air leaves the evasee of the fan with a velocity of 500 feet per minute, what proportion of the power supplied is being used up in this velocity of efflux? Assume your own figures for the temperature and density of the air. (30) 4. Sketch, and describe briefly, a Sirocco mine ventilating fan, giving its characteristic features. (30) 5. Row would you test in a mine for firedamp with a flame safety-lamp? Give the heights of cap for each percentage in the lamp you make use of. Describe any other methods in use for testing for gas in the mine. (30) 6. What is the characteristic principle of the Mueseler type of safety-lamp? Sketch a lamp using this principle. (30) 7. A pair of shafts are each 500 yards deep and 21 ft. diameter, Taking the surface barometric pressure as 30 inches, the average temperature in the upcast as 75°F., and that of the downcast as 55°F., calculate the height of the motive column in this case. (30) 3. — EXPLOSIONS, ETC. 1. Write an account of an investigation after an explosion, with particular reference to indications as to the point of origin, and cause. (30) 2. In consequence of an underground fire, the question of reversing the ventilation arises. What matters should be considered before deciding whether the reversal shall be carried out? (25) 3. Describe in detail the arrangements you would make for unwatering an area of waterlogged workings lying to the rise. The workings are sealed off by darns in two cross-measure drifts, the water pressure on the dams being 250 lb. per sq. in. (25) 4. What are the objections to using certain kinds of incombustible dust on the roadways in mines for preventing the propagation of an explosion? Why is a highly hygroscopic dust undesirable ? Describe suitable tests for this. (25) 5. An air sample taken from the return airway of a district in a seam of coal liable to spontaneous heating shows the following analysis :— CO ... .~. .. .. 0-400 per cent. CR .. -. -. .. 1•170 02 .. ,. .. ... 19-920 ,, N2 .~. .~ .. .. 78490 CO ..., ... .. ... 0020 100-000 What deductions would you make from this analysis, and on what grounds would you base your deductions? (25) 6. In What respects do the following rescue apparatus differ (a) oxygen apparatus; (b) liquid air apparatus; (c) smoke helmet? Make a diagrammatic sketch of a type of self-contained breathing apparatus. What are the limitations of the smoke helmet? (25) 4. — MACHINERY. Electrical Section. — 1. A 3-phase alternator delivers power to an overhead bare copper transmission line at a pressure of 3,300 volts without transformation. Give a list of the apparatus and instruments that might be installed between the alternator and the line for controlling and protecting the alternator. (28) 2. A 3-phase transmission line has bare copper conductors 0.04 sq. in, sectional area and is one mile long. The resistance of copper Wire 0.04 sq. in. is 0.6 ohm/l,000 yards. Electric power is fed to the line at the rate of 1,000 kw. at 3,300 volts and the power factor is 0.8. What kilowatts are delivered by the transmission line? (28) 3. Describe briefly, using simple diagrams, the three chief types of direct-current motor and state a purpose for which each type is peculiarly suitable. Row is the direction of turning of each type reversed? (28) Mechanical Section. — 4. State what is meant by the following descriptions of materials and name one article for which each material is specially suitable (a) Manganese steel; (b) Chilled cast-iron ; (c) Nickel steel ; (d) Case-hardened steel. (28) 5. Describe a Lancashire boiler. Name approximately the largest Lancashire boilers made (length and diameter). State the highest steam pressure for which Lancashire boilers are suitable. (28) 6. The longitudinal joints of the plates in a Lancashire boiler are of the butt type with the following specification: Plate thickness, 1 in. ; Rivet holes, 1 in. diam. ; Cover plates, 9¼ in. wide Rows of rivets, 4, Spacing of rivets longitudinally, 3 in.; Spacing of rows of rivets transversely from one side of cover plate to the other — 1¾ in., 1½ in. — joint — 1½; in. 1¾ in. Make a plan of this joint to a scale of one-quarter full size showing a length of about 18 in. of the joint. The rivet holes can be indicated by crossed centre lines at the correct points except for one hole in each row, which should be shown correctly to scale. Show all necessary dimensions. The curvature of the shell plate can be ignored. (38) 7. Write a short essay on steel wire winding ropes dealing with their construction, installation and treatment in use. Note especially points connected with safety. (28) 8. A centrifugal, or turbine, pump has five impellers in series 13 in. diam., running at 1,440 r.p.m. The delivery branch is 7 in. bore and the suction branch is 8 in. bore. For what rate of delivery of Water and head would this pump be suitable? (28) 5. — SURVEYING, LEVELLING, AND DRAWING. 1. The plan on separate sheet shows an area of coal workings in a shallow seam with levels therein, and several contour lines on the surface in the vicinity of the coal face. Lay down on the plan a line representing as much of the inferred outcrop of the seam as the contour lines shown will allow. Assume an average thickness of 30 ft. of alluvium overlying the rockhead. (30) 2. The following readings on a levelling staff were taken with a dumpy level at a point A, the staff being held successively at 1- chain intervals along the centre line of a proposed road: At peg 0 chain .. .. .. 4.78 feet. ,, 1 chain .. .. .. 9.80 ,, 2 chains .. .. .. 9.36 ,, ,, 3 chains .. .. .. 14.62 The level was then moved to a point B and further readings taken as follows :— At peg 3 chains .. .. .. 2.78 feet. ,, 4 chains . . .. .. 2.21 ,, ,, 5 chains .. .. .. 8.99 ,, 6 chains .. .. .. 14.94 The height above datum of peg 0 chain is 130 ft.: (a) Set out the above readings in your answer book in the form you would take them in the field. (b) Reduce them by The rise and fall method. (c) Plot a section from peg 0 chain to peg 6 chains on a scale of 1 in. to a chain for horizontals and 1 in. to 10 ft. for verticals. Mark the depth of filling or cutting at each peg to give a uniform gradient from peg 0 chain to peg 6 chains. What is that gradient? (30) 3. Two underground roadways AB and AC, diverging from a common point A and bearing N.30°W. and N.30°E. respectively, are connected by another roadway BC, which is 600 ft. in length, and bears from B to C in the direction S.75°E. Calculate the length of the roadway AC. (30) 4. Calculate the co-ordinates of the undernoted survey or traverse, and the bearing and length of the joining line from. A to B: From A S.41°W. .. .. .. 180 feet S.48°.E. .. .. .. 160 E. .. .. .. 200 N.50°E. .. ... .. 140 N.40°W. .. .. .. 200 ,, to B. (30) Note. — The values of the trigonometrical ratios necessary for solution will be found below. 5. Describe briefly how you would accurately measure a survey line over steep and rough ground. A survey line across a fairly deep ravine has been measured as accurately as possible. Describe, with sketches, how you would check the measurement so obtained by using: (a) chain and ranging poles only; (b) theodolite, chain, and ranging poles. (20) 6. State the equivalent in inches to a mile of the following scales, viz.: 1/10560, 1/1584, 1/500. If the area of a field marked on a map drawn on the above scale first mentioned is 1.75 sq. in., what is its area in sq. in. on maps drawn to the second and third mentioned scales respectively ? (20) TABLE OF NATURAL SINES, ETC. (see Question 4). Angle. - Angle. Degrees. Sine. Cosine. Tangent. Cotangent. Degrees. 40 •643 ~766 •839 1192 50 41 •656 •765 S09 1-150 49 42 ~6fi9 .743 900 1111 48 43 731 ~932 1072 47 44 •f~95 ~719 906 1035 46 45 ~707 707 1.000 1~000 45 Cosine Sine Cotangent Tangent 6. — GENERAL MANAGEMENT AND MINING LEGISLATION. 1. Compulsory Question. — The output at a colliery has, for no apparent reason, decreased after a few years of good outputs. There has been no change in the coal seams and there are ample reserves of coal. Write a report suggesting the lines of an investigation into the causes of the decrease in output, and possible remedies. (30) 2. Specify the requirements of the Coal Mines Act, 1911, as to travelling on haulage roads and the provision of clear space for travelling. (25) 3. Give a summary of the provisions contained in the Acts of Parliament limiting the hours of workmen at collieries: (a) Underground; (b) On the surface. (25) 4. State the different occupations or positions at a mine for which an age limit is fixed, and state the age limits for each. (25) 5. Give fully the rules which apply to the storage and use of detonators. What dangers may arise in handling detonators? (25) 6. State the definitions given in the Coal Mines Act, 1911, of the following : (a) "A place not deemed to be in a fit state for working or passing therein." (b) "An intake airway not deemed to ho normally kept free from inflammable gas." State the conditions as to mixtures of air and inflammable gas under which men must be immediately withdrawn. (25) * Questions set at Examinations in November, 1931. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Complete sale of questions available through H.M. Stationery Office, 1s. 6d. net.
|
|||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||