|
23rd January 1932, Page: 219, Column: 1 Examination QuestionsSurveyors' Certificate.*Morning Session. — 1. The plan on separate sheet is copied from an Ordnance Survey Geological map. State fully what information the plan conveys to you with regard to the geological features of the area, and also your inference — and the reason for it — as to the general direction of dip of the strata, and the approximate rate of dip. Two bores have been put down, one at the point marked A on the plan, and the other at the point marked 13. State what seams would be cut in each bore, and at what depth from the surface each would be found. The thickness of strata between the various seams referred to is as follows : Between Fireclay seam and Main Coal . . 12 fathoms. Main Coal and Steam Coal . . 11 ,, ,, Steam Coal and Gas Coal . . 9 ,, ,, Gas Coal and House Coal .. 8 ,, (14) 2. A cylindrical bar, 3 inches in diameter and 4 inches long resting with one end on the horizontal plane, is cut by a plane passing through the top left-hand corner of its elevation and making an angle of 60 degrees with its axis. Draw a plan and elevation of the bar, and also the true shape of the section. All projection lines must be clearly shown. (12) 3. Calculate the difference in length of an arc of 10 of longitude at latitude 56° and latitude 57°, if the radius of the earth at the equator be 3962.8 miles. (10) 4. A cylindrical tank filled with water is 6 feet in height and 8 feet in diameter, and is tilted so that its base lies at an angle of 22½° from the horizontal. Calculate the amount of water in gallons remaining in the tank. (8) 5. The undernoted co-ordinates, stated relative to a common point of origin, represent the bearings of two stretches of roadways AB and CD. A N. 850 feet .. .. .. .. E. 450 feet. B N. 700 ,, .. .. .. .. W. 100 C = S. 500 ,, .. .. .. .. E. 500 ,, D=N.110 ,, .. .. .. .. E. 30 Calculate the co-ordinates of a point X where the projected courses of AB and CD will meet. (8) Afternoon Session. — 1. Compulsory Question. — Undernoted are the details of a theodolite traverse of part of a main roadway and also of part of a narrow and undulating airway in a mine. It is proposed to improve the ventilation by driving a new drift dipping at 1 in 10 from the point C on the same bearing as line BC to connect with a level stone drift to be driven from the point G. Calculate the bearing and length of the level stone drift to be driven from the point G to connect with the new dipping drift from point C above referred to. Length, Observed Vertical Line Feet. Angle. Angle. Azimuth. AB 4935 - - 5000, 179'55' BC 500-1 179'55' - 5Ol0~ CD 1816 119011~ +l5o30~ DE 3120 221'34' +12'4-1' El" 3200 227'03' 19017 FG 203-2 305048~ ~14o15~ (14) 2. The plan on separate sheet shows an area of coal workings in a shallow seam with levels therein, and several contour lines on the surface in the vicinity of the coal face. Lay down on the plan, in the manner in which it would be shown on an Ordnance Survey geological map, as much of the inferred outcrop of the seam as the contour lines shown n-ill allow. Assume an average thickness of 30 feet of alluvium overlying the rock head. (12) 3. The undernoted diagram, which is not drawn to scale, shows the details of a subsidiary triangulation. The line joining stations A and C measures 2,987 feet. Calculate the length of the line ED. (12) 4. A triangular area of ground shown on an Ordnance Survey map of 1/1250 scale has sides of the following lengths 7.50"; 8.00"; 9.10". it is subsequently found that the map has shrunk to the extent that the long and short marginal lines are respectively 42 feet and 28 feet short. Calculate the correct area of the triangle. (10) 5. Workings in a coal seam 3 feet in thickness and lying at a depth of 600 yards or thereby are about to be carried under part of a colliery leasehold where valuable property has been erected. A record of the resulting subsidence is desired. The nearest reliable Bench Mark is about a mile distant, and the intervening ground is undulating, with one stretch of roughly 150 yards on a gradient of 1 in 5. Describe briefly the essential features of an up-to-date instrument suitable for carrying out the necessary levelling with precision. State also how you would conduct the levelling operations from the Bench Mark to the property area, and the measures which you would adopt in order that the resultant subsidence of each individual property could be accurately determined from time to time. (8) 6. In constructing a branch railway to a colliery, two portions of straight line, between which there is an angle of 110°, are to be connected by a curve of 15 chains radius. Calculate the distance from the intersection of the two "straights" at which the curve will begin and end, and the tangential angle which you would use in directing the setting of the pegs by the aid of a theodolite. If it were found necessary to move the instrument after setting several pegs on the curve, state clearly, with sketch, how you would proceed in directing the placing of the succeeding pegs. (8) * Questions set at Examinations in November, 1931. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Complete sets of questions available through H.M. Stationery Office, 1s. 6d. net.
|
|||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||