Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

8th August 1931, Page: 21, Column: 1

Examination Questions

Surveyors' Certificates.*

Morning Session. — 1. The plan on separate sheet shows details taken from a Geological Survey map on a scale of 6 inches to 1 mile, together with a general section showing the relative positions of the various seams, outcrops of which are shown. Draw a section on the line EF to the same scale as the plan, showing the surface contour and the position of the several coal seams, and state the direction and approximate amount of throw of the faults marked AB and CD on the plan. Assume a uniform thickness of 40 feet of alluvium overlying the rockhead. State what is meant by the geological signs shown on the north-west area of the plan. (12)

2. Construct a one-minute vernier which would be suitable for a 4-inch theodolite graduated clockwise, the whole circuit of which is divided into half-degrees. Construct the vernier to show a line of incidence of 227 degrees 12 minutes with the whole. circle. All calculations from which the construction is based must be shown. (12)

3. A triangular area of ground has sides of the following lengths, viz.: AB, 585 links; BC, 748 links; CA, 887 links. It is proposed to set off a straight line DE parallel to the side AB so that the area of the figure ABED will be equal to 125 acres. Show how you would determine the position of the line DE. (8)

4. The apparent capacity of a water tank in the form of a cube, as determined from a drawing to scale of 3/8-inch to 1 foot, is 15,377 gallons. It is subsequently discovered that, instead of the above scale, a scale of inch to 1 foot was erroneously used when estimating the above capacity. Calculate the correct capacity of the tank. (8)

5. It is proposed to work 28 per cent, of a coal seam by the method known as "stoop and room," or "pillar and stall," leaving rectangular stoops or pillars, the length of which shall be to the breadth as 3 to 2. If the rooms or stalls are formed 10 feet in width, calculate the size of the stoops or pillars to fulfil the above conditions. (8)

Afternoon Session. — 1. The drawing on separate sheet is a sketch plan which indicates the embankment necessary to connect an existing bridge-level to a new screen gantry. Calculate the approximate quantity of filling required to form the embankment according to the levels and other details shown on the sketch plan. Assume the angle of the slopes to be 1½ horizontal to 1 vertical. (12)

2. The undernoted traverse was made with a 5-inch theodolite graduated clockwise

Distances. Horizontal Lines. (feet). angles. Azimuth. 1 .. •~. .. 280.5 .. .. 148°1'10" 2 .. .. ,. 234.9 ,. 202°51'02" 3 ., .. .. 394.7 .. 281°24'55" 4 .. .. .. 427 .. 225°20'03' 5 .. •. .. 252.5 .. 83°17'50" 6 ,. .-. .. 500 .. 170°18'00"

It is proposed to drive a drift from the initial point of the traverse in the direction S.51°45'W. which will intersect lines 4 and 6. Calculate the points in these two lines at which it will do so. (12)

3. Three trigonometrical stations, A, B, and C, lie in a straight line on the same plane. From each station an angle of elevation taken to the top of a colliery chimney situated on high ground, which is not in a straight line with A, B, C, is found to be as follows: At A, 12°30'; at B, 18°50'; at C, 21°10'. Station B is 1,980 feet from A, and C 1,010 feet from B. Calculate the perpendicular height of the chimney top above the plane of the three stations. (12)

4. A circular wall surrounding a disused colliery shaft is observed from two points A and B, which form the extremities of a base line 850 feet in length. Angles measured at A to the tangential points of the wall C and D are as follow: C A B , 12°15'; DAB, 19°31'. Angles measured at B to the tangential points of the wall E and F are as follow : F B A , 23°17'; E B A, 19°05'. Calculate the diameter of the circle formed by the outside of the wall. (8)

5. Calculate the area enclosed by (a) the bounding lines of an Ordnance Survey sheet on scale 1/2500 (b) the bounding lines of an Ordnance Survey quarter-sheet on scale 1/10560 (c) the 55° and 560 parallels of latitude and 1° and 2° parallels of longitude. What is the length of 1 degree of latitude ? (8)

6. Two levels 60 yards apart run parallel due east and west in a coal seam dipping due north at 1 in 12. From a point in the lower of the two levels a cross-measure drift is driven, bearing N.20°E. and rising 1 in 4, to intercept a seam 60 yards vertically above the lower seam. From a point in the upper level a second cross-measure drift is also driven to intersect the upper seam rising 1 in 6 on a line parallel to the first and 60 yards distant south-eastwards on plan therefrom on a line at right angles thereto. Calculate the bearing between the points at which the respective cross-measure drifts meet the upper seam. (8)

7. State fully, but concisely, how you would accurately determine the depth of the following shafts : (a) A rectangular shaft, lined with timber and approximately 400 yards in depth; (b) a circular shaft, 20 feet in diameter and approximately 700 yards in depth, of which a length of 160 yards, or thereby, is lined with cast-iron tubbing. (8).


* Questions set at Examinations in May, 1931. For First Class Questions see No. 26, Volume 41. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Complete sets of questions available through H.M. Stationery Office, 1s. 6d.


Related Articles

Pub.
Date
Article (Newspaper)
07 Mar 1931  Board For Mining Examinations (The Science and Art of Mining)
11 Jul 1931  Examination Questions, First Class (Managers).* (The Science and Art of Mining)
08 Aug 1931  Examination Questions, Second Class (Under-managers).* (The Science and Art of Mining)
08 Aug 1931  Examination Questions, Surveyors' Certificates.* (The Science and Art of Mining)
08 Aug 1931  Examination Results (The Science and Art of Mining)

 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print