|
8th August 1931, Page: 20, Column: 1 Examination QuestionsSecond Class (Under-managers).*1. — MINE WORKING. 1. Describe in detail the cycle of operations on a longwall coal-cutting and conveyor face in order that a regular system of work may be maintained over a definite period. (60) 2. Under what conditions would you use steel arches and cambered girders respectively ? Give your reasons. What is your opinion of using steel arches near the face, and state the provision, if any, that you would make for the preliminary squeeze of the strata? (60) 3. Coal-cutting machinery and conveyors are installed in a seam, and have to work under a roof which, in one district, crumbles and tends to fall in small pieces, and, in another district, tends to fall in large blocks. Describe in detail how you would support the roof under each condition. (60) 4. What are the causes of blown-out shots ? Describe the procedure in case of a missfire. (60) 5. Show in detail the method of supporting 2-ft. diameter ventilation pipes in a sinking shaft. Would you arrange the fan to blow or exhaust, and why? (60) 6. What are the principal matters to which an under-manager should give his attention on making his ordinary inspection of a district? (60) 2. — THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine, which accompanies this paper, show how you would ventilate the working places Mark the direction of each air-current; also indicate clearly the positions of air-crossings, doors, stoppings, regulators, and sheets ; using the signs laid down in the Regulations. Sheets to be shown thus S. (75) 2. Sketch an air-crossing. To what points would you pay attention in order to ensure that the structure is satisfactory? (45) 3. What is a water-gauge as used in ventilation; and what is it used for? Sketch, as if actually in use, some type known to you. (45) 4. The fan drift is 12' 6" high by 10' 6" wide. If the average velocity of the air is 1,200 feet per minute, calculate the quantity. If the water-gauge is 4 inches, what is the horse-power of ventilation? What horse-power would you install to ensure that the fan gives this quantity? (45) 5. Describe briefly, with sketches, a flame safety-lamp, paying special attention to the more important parts. (45) 6. What proportion of the air-current at the pit bottom would you expect to find circulating at the working faces? State what steps you would take to make the ventilation as efficient as possible in this regard. (45) 7. A main intake is 10' wide by 7' 6" high near the pit bottom; 600 yards further in it is lined with straight-sided steel arches 8' wide by 6' high, the curved part being semi-circular. Nearer the face it is lined with similar arches 7' wide by 6' high. The quantity of air passing is 45,000 cubic feet per minute. Calculate the velocity at each of the three points named, neglecting leakage. Make any suggestion you like as to how this airway could be improved. (45) 3. — EXPLOSIONS, ETC. 1. Sketch and describe a system of working suitable for a seam of coal liable to spontaneous heating. (20) 2. What precautions would you take in working a seam of coal when the faces are approaching an area of old workings full of water lying in another seam 100 yards above the working faces? There are several faults in the locality. (20) 3. Give approximate analyses of: (a) A dust that would intensify an explosion in air free from firedamp ; (b) a dust that would prevent the extension of an explosion in air free from fire-damp. (20) 4. If you were in the distant workings of a mine, and you saw smoke coming in with the intake air, what causes would you suspect, and what steps would you take? (20) 5. Make a diagrammatic sketch of a type of rescue apparatus with which you are familiar. What tests would you make before using the apparatus in a poisonous atmosphere? What risks are to be guarded against in its use (20) 6. Describe fully, and give sketches of, a suitable stopping for a gateway or pack road to seal off a gob-fire, and mention any special precautions which you would take during the sealing off. (20) 4. — MACHINERY. 1. Describe what is meant by the terms (a) Cam; (b) eccentric; (c) crank. State a use for which each of these devices is best suited. (20) 2. Sketch and describe a good capel for a wire winding rope about 1 inches diameter, and also describe the fitting of the capel to the rope. (20) 3. A three-throw pump has single-acting rams 8½-inch diameter by 10-inch stroke. At about what speed should the crankshaft revolve to handle 250 gallons per minute of water, and what should be about the brake-horse-power of an electric motor to drive the pump if the total head from all causes is 400 feet ? (20) 4. What is hardness in a boiler feed water? Some boilers are regularly blown off, the water-level in the gauge glass being lowered an inch or so. Why is this done ? (20) 5. Describe a switchgear suitable for controlling a coal-cutting machine circuit and for placing in a road near the coal face. Choose either a direct-current or a three-phase system, stating which you adopt. (20) 6. Describe, with the aid of a sketch, one method of directing steam into the cylinder of an engine so as to drive the piston to and fro. Name a method of ascertaining whether the steam is being used correctly and economically in the engine. (20) 5. — ARITHMETIC AND SURVEYING. Arithmetic. — 1. A contractor undertakes to drive a cross-measures drift for £5 5s. per yard. What sum would be due to him if you found he had driven 37 feet since last payment? What is the cost per cubic yard of material removed if the drift measures 10 feet by 6½ feet? (20) 2. A mining lease stipulates that a certain seam underlying a reservoir is to be worked by the method known as pillar and stall. If the stalls are 10 feet in width and the pillars 66 feet square, what percentage of the seam is contained in the pillars ? (20) 3. An ingot of iron in the form of a cylinder 6 inches in diameter and 4 feet in length is about to be rolled into a bar 3 inches in breadth and 1½ inches in thickness. If 2½ per cent. of the bulk be lost in the process, calculate the length of the rolled bar. (20) 4. Part of a colliery leasehold is in the form of an equilateral triangle with sides 200 yards in length. A seam 5 feet in thickness was worked out from under this area and yielded altogether 26,445 tons. Find the percentage of loss in working, taking the specific gravity of the seam at 1.28. (20) Surveying. — 5. Plot the following short survey or traverse to a scale of 1 inch to 100 feet:— From A. N.55°W. 200 feet. W. 155 feet. S.10°W. 310 feet. E.80°E. 165 feet to B. Find the bearing and distance from A to B. Join AB and calculate the area of the closed figure. (20) 6. Draw on your answer book a line to represent the magnetic meridian on a plan as at present time. Through a point on that line draw another line representing the magnetic meridian as it will be 15 years hence, assuming that the change of meridian will be in the same direction as at present and at the rate of 12 minutes per annum. If the magnetic bearing of a wall determining a leasehold boundary is now N.2°E., what will the bearing of the same wall be 15 years hence on the above assumption? (20) 7. Draw an equilateral triangle ABC with sides 4½ inches. Assume the triangular area to be part of a colliery plan drawn to a scale of ½ inch to 1 chain, and that the relative levels of a seam at the points A, B and C are 60, 159 and 258 feet above datum respectively. Show on your drawing the direction of level course, and the direction of full dip. What is the rate of full dip? (20) 6. — MINES ACT, ETC. 1. Compulsory Question. — As under-manager, write a report to your manager, of an accident to a winding engine used for raising men and coals which occurred when you were underground, soon after the pit started drawing coals, and assuming that you are informed that the repairs will occupy about six hours. State exactly what steps you took on hearing of the breakdown. (20) 2. What steps have to be taken when a mine or seam is abandoned? What particulars are required to be shown on the plan to be sent to the Mines Department? (20) 3. State the provisions of the Coal Mines Act, 1911, as to the dimensions of travelling roads and the powers of H.M. inspectors with relation thereto. (20) 4. State the provisions of the Coal Mines Act, 1911, relating to restrictions on the use of electricity in any parts of a mine. What is the procedure to be observed under the General Regulations when it is intended to introduce electrical apparatus into any mine? (20) 5. What are the requirements of the Coal Mines Act, 1911, and the General Regulations concerning winding engines? (20) 6. Specify the occurrences in and about a mine which have to be reported to H.M. inspectors of mines even if they do not cause personal injury. (20) * Questions set at Examinations in May, 1931. For First Class Questions see No. 26, Volume 41. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Complete sets of questions available through H.M. Stationery Office, 1s. 6d.
|
|||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||