|
11th July 1931, Page: 404, Column: 1 Examination QuestionsFirst Class (Managers).*1. — WINNING AND WORKING. 1. In a 6-foot seam, dipping 1 in 8, it is decided to pack solid on a longwall face by means of a scraper loader. Describe how you would do this, and how you would get the debris tight against the roof. Illustrate your answer by sketches. (50). 2. What are the principal geological formations above the Carboniferous? Name them in the order in which they were deposited. (40) 3. Explain in detail how you would change a lock-coil winding rope used in a shaft 600 yards deep. How often would you recap? State how much rope you would cut off each time, and by what means you would cut it. (40) 4. Under what conditions would you use steel arches and cambered girders respectively ? Give your reasons. What is your opinion of using steel arches near the face, and state the provision, if any, that you would make for the preliminary squeeze of the strata? (40) 5. A shaft of 21 feet diameter inside the lining is being sunk through dry strata. Give a description of the work as it proceeds; paying particular attention to the shot-firing. (40) 6. Two shafts are sunk to a depth of 800 yards. Coal is wound from the full depth up one of the shafts, but only from a depth of 500 yards up the other shaft. Describe, with sketches, the arrangements you would make at each shaft in order to provide a second outlet for the men working at the respective depths. (40) 7. To what uses in mining, apart from sinking, can the cementation process be successfully applied ? Describe fully the method of application in one of the cases you quote. (40) 2. — THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine which accompanies this paper, show how you would ventilate the working places. Mark the direction of each air-current; also indicate clearly the position of air-crossings, doors, stoppings, regulators, and sheets ; using the signs laid down in the Regulations. Sheets to be shown thus S. (50) 2. Describe, with sketches, the Steart (or multiple propeller) ventilating fan, giving the details of its construction, the principles upon which it operates, and enumerate what, in your opinion, are the advantages and disadvantages of this fan. (30) 3. At a large deep new colliery, working a fiery seam, what arrangements for lighting do you consider should be adopted: (a) Near the shaft bottom; (b) On the roadways; (c) At the working faces? Describe briefly the various lamps you would use. (30). 4. It is proposed to wind large quantities of coal at both the downcast and upcast shafts. Sketch the arrangements you would adopt at the surface to enable this to be done without interfering with the ventilation. (30) 5. State fully what means you would adopt to ensure that a good proportion of the air-current produced reaches the working faces. What would you consider a satisfactory proportion: (a) In advancing longwall where the faces average a mile from the shaft bottom; (b) In retreating longwall where the faces average half a mile from the shaft; (c) In pillar and stall workings a mile from the shaft? (30). 8. Sketch an air-crossing. What are the principal objects aimed at in the construction, and how would you ensure their achievement? (30) 7. A fan produces 300,000 cubic feet of air per minute at a mine with a 4-inch water-gauge. Calculate the horse-power of ventilation, and state the power you would install to ensure the fan giving this quantity. If the quantity is required to be increased to 400,000 cubic feet in the same mine, what would be the new horse-power and water-gauge? (30). 3. — EXPLOSIONS, ETC. 1. In what directions has scientific research lessened the risks of explosions and fires in mines? (30) 2. Which of the two permissible systems of rescue organisation do you prefer? Enumerate their relative advantages and disadvantages. (25) 3. As manager you receive a report that spontaneous heating is suspected in a section of the mine. Describe in detail the steps you would take to make an investigation, and to eliminate possible elements of danger. (25) 4. A seam of coal is being worked adjoining an old colliery which is full of water. Give an account of all matters which should be investigated to ensure the safety of your workings. (25) 5. What arrangements should be made at the surface with the object of preventing coal dust from the screens from entering the mine? In what parts of the mine would you expect to find the most dangerous dust? Describe conditions that would lead you to consider that the dust is dangerous, and state how you would deal with such conditions. (25) 6. During recovery work after an explosion men have been found alive, but unconscious, by a rescue team wearing self- contained breathing apparatus. Assuming that the team is 300 yards from the base, what steps should be taken? (25) 4. — MACHINERY. Electrical Section — 1. What particulars and data do you expect to find on the name-plate of an electrical transformer? What tests would you apply to a transformer to ascertain that it was in good and correct working order? (28) 2. Describe carefully the construction of an induction motor for 3-phase current with a wound rotor (say for 100 horse-power at 960 revolutions per minute, 50 cycles). Deal especially with the electrical circuits of the motor, giving a simple diagram to show the connections of the coils among themselves and with exterior cables. (28) 3. Describe the apparatus that you would expect to find in an electrical haulage gear house for working, controlling and protecting the motor. What are the essentials of flame-proof switchgear? (28) Mechanical Section. — 4. The drawings on the separate sheet show the bed of a three-throw pump, also gear wheels, and a motor which is to be placed on the bed to drive the pump through the gears. Show, by freehand sketching on the sheet, with written notes, how you Would gear the motor to the pump. Have in mind the protection of the motor from chatter or vibration from the gearing and also arrange to allow the rotor to have play axially. In answering this question, the arrangement adopted is more important than the quality of the sketching, which, however, should indicate clearly what is meant. (38) 5. Describe a pumping plant for a sinking shaft to include a centrifugal (Or turbine) pump, coupled direct to an electric motor, and the accessories of the pump which is to be arranged to follow the sinking as it proceeds. (28) 6. Explain carefully what causes certain waters to be bad for feeding boilers. When a bad feed water has been treated to make it suitable for use in boilers, does it behave within the boiler in the same Way as a good untreated water? Explain your answer. (28) 7. Describe a boiler of the Stirling type, i.e., with bent, highly inclined, tubes, illustrating your answer with a simple sketch showing a side elevation of the boiler. What is a usual diameter for the Water tubes? (28) 8. An output of 500 tons of coal is to be delivered up an incline 700 yards long, dipping 1 in 8, laid With two tracks, in tubs holding 20 cwts., in 7 hours, by direct two-rope balanced haulage, the power being steam at about 80 lb. per square inch. Describe the hauling engine that you Would install, giving the chief drum and cylinder dimensions. (28) 5. — SURVEYING, LEVELLING AND DRAWING. 1. The plan on separate sheet shows the centre line of part of a proposed colliery railway, contour lines of adjoining ground, and the level of the surface of the ground at each peg. The formation level of the railway at peg 10 is 20 feet above datum, and the gradient is 1 in 100 rising in the direction of peg 13. Plot a longitudinal section from peg 10 to peg 15 on a scale of 1 inch to 100 feet for horizontals, and 1 inch to 10 feet for verticals of section. Show the formation level, and mark the depth of cutting at each peg. Plot cross-sections at pegs 12, 13 and 14 to a scale of 1 inch to 10 feet and calculate therefrom the amount of cutting in cubic yards between pegs 12 and 14. Assume the Width on formation level to be 15 feet and the angle of the slopes 1 vertical to 1½ horizontal. (30) 2. A colliery leasehold measures 1 mile square in area. It is intersected by a large fault which runs parallel to two of its sides. and has a vertical displacement of 80 yards. The hade of the fault is 30° from vertical. Calculate the quantity of coal within the leasehold, assuming a total thickness of 15 feet, with specific gravity 125, and that the strata dip in 1 in 6. If you were asked to estimate the sale product of the leasehold, What further deduction in addition to the large fault would you make from. the above quantity? Assume longwall working throughout. (30) 3. The co-ordinates of two parts, A and B, in relation to a common point of origin, are as follows Latitude. Departure. A North 188.6' .... East 922.4' B South 495.4' .... East 58.6' Calculate the co-ordinates of a point P which lies midway between A and B. Check your result by plotting on a scale of ½ inch to 100 feet. (20) 4. The rate of full dip of a coal seam is 1 in 10 (one vertical to 10 horizontal). A haulage road advancing direct to the rise strikes a fault bearing at right angles to it. A prospecting drift is driven down the bade of the fault and proves the seam to be thrown down 60 feet measured from floor to floor on the angle of the hade, which is 30° from vertical. The direction of full dip of the seam beyond the fault is unaltered, but the rate of dip has increased to 1 in 6. It is proposed to win the seam beyond the fault by driving a cross-measure drift in the same direction and on the same gradient as the haulage roadway. Calculate the length of the cross-measure drift necessary to win the seam, and check your answer by drawing a section to scale of 1 inch to 100 feet. (30) 5. Plot the following short survey, or traverse, to a scale of 1 inch to 100 feet :— From A: N.38°E. 215 ft. level. N.25°W. 250 ft. rising 1 in 2. N.85°E. 325 ft. level. S.40°E. 134 ft. dipping 1 in 3. S.10°W. 262 ft. level to B. Join A and B, and mark the quadrant bearing and distance from B to A. Calculate the enclosed area by reducing it to a single triangle, giving the answer in acres and decimals, (30) 6. State briefly what is meant by the undernoted terms, all of which are used in connection with levelling : (a) Contour line ; (b) datum line ; (c) back-sight; (d) fore-sight; (e) line of collimation. (20) 6. — GENERAL MANAGEMENT AND MINING LEGISLATION. 1. Compulsory Question. — Draw up a form of cost sheet and return, showing the particulars you would, as manager, require from time to time and insert assumed figures typical in your district. (30) 2. State the provisions of the Coal Mines General Regulations (Safety-Lamps), 1927, as to the unlocking of safety-lamps underground and what alteration came into force on January 1st, 1931. What is the effect of the alteration ? (25) 3. What are the provisions of the Coal Mines Act, 1911 (Section 78), with regard to drilling in highly silicious rock? Who may be held responsible for contravention or non-compliance? To what does the General Regulation of June 3rd, 1920, relating to this subject, apply, and what is the definition of "stone" contained therein ? (25) 4. State the General Regulations as to the use of explosives on main haulage roads and main intake airways. What is the definition given of a "main haulage road"? (25) 5. State briefly and concisely the provisions contained in the Coal Mines Act, 1911, and General Regulations for the care and treatment of animals underground. (25) 6. Give the requirements of the Coal Mines Act, 1911, as to the steps to be taken on the abandonment of a mine. What definition is given of "abandonment"? (25) * Questions set at Examinations in May, 1931. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Complete sets of questions available through H.M. Stationery Office, 1s. 6d.
|
|||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||