|
7th February 1931, Page: 230, Column: 1 Examination QuestionsSecond Class (Under-managers)*1. — MINE WORKING. 1. Sketch a hand-got longwall district to produce 150 tons of coal per shift from a seam 5 feet thick, with a good roof and floor. Sketch in detail one working place, showing drawing road and timbering; give approximate dimensions. (60) 2. A cross-measure drift 10 feet wide by 7 feet high and dipping 1 in 8 is in the course of being driven through ground which requires to be well supported, when it is found that the floor level at the face is 8 feet too high. How would you proceed to rectify the mistake ? (60) 3. Show, by sketches, how you would fence: (a) A 4 feet return haulage pulley placed horizontally in a road where men have to travel beneath it. (b) A small haulage engine placed on one side of a road on which men travel. (60) 4. It is found that the proportion of large coal being made in a seam under your charge is too low. What reasons can you give for such a state of affairs, and what suggestions can you make to reduce the amount of small coal ? (60) 5. What do you consider is the most dangerous circumstance to guard against in connection with shot-firing ? Do you prefer clay or sand for stemming? Give the reason for your preference. What is the best position for the detonator in the shot-hole ? (60) 6. In connection with endless rope haulage on an incline, compare, in detail, the advantages and disadvantages of over-rope and under-rope respectively. How would you attach the tubs to the rope in each case? Give reasons for your choice. (60) 2. — THEORY AND PRACTICE OF VENTILATION. 1. See Q. 1, Subject 2, First Class. (75) 2. Sketch and describe one type of air-bridge or air crossing. (45) 3. In passing through a ventilating district, water-gauge readings are taken at four separation doors, but no two of these readings are alike. Explain why this is so. (45) 4. A quantity of 200,000 cubic feet per minute is produced at a mine and the water-gauge reading in the fan drift is 3 inches. Assuming the fan has an efficiency of 65 per cent., calculate the necessary horse-power to be imparted to the fan by the engine or motor. (45) 5. An airway lined with semi-circular steel arches with straight legs is 10 feet wide and 8 feet high. If the velocity of the air current passing is 800 feet per minute, calculate the quantity. Farther on in the same air-way the arches are 8 feet wide and 6 feet high; calculate the velocity of the same current at this point. (45) 6. State the composition of the principal gases met with in mines (including atmospheric air) and give their properties. (45) 7. Give the limits of explosibility of mixtures of firedamp and air, under ordinary mine conditions. (45) 3. — EXPLOSIONS, ETC. 1. How do you account for the fact that in several recent explosions the explosive wave has extended chiefly towards the upcast shaft? State the possible causes of ignition in colliery explosions of firedamp and of coal dust respectively. (20) 2. In a mine where naked lights are permitted, what precautions would you take for the prevention of fires caused by using such lights? (20) 3. What can be done to reduce the making and deposition of coal dust in a mine ? Describe the precautions to render coal dust incapable of initiating, or propagating, an explosion. (20) 4. Sketch and describe suitable boring apparatus for use when approaching old workings containing a dangerous accumulation of water. Make a sketch showing how you would arrange the bore-holes so as to give a minimum protection of 5 yards. (20) 5. To what extent can the workmen assist in reducing the risks of spontaneous heating? What indications should they be able to detect at the commencement of spontaneous heating? (20) 6. In reopening the workings of a mine after an explosion how would you organise rescue men for repairing an air-crossing 100 yards from fresh air, it being very necessary to do the repair quickly? (20) 4. — MACHINERY. 1. What particulars and data do you expect to find on the nameplates of electric motors of the kinds in common use in collieries? If a motor had lost its nameplate, what would you look for in its details of construction to find out what kind of a motor it was ? (20) 2. Describe the riveting of the longitudinal joints of the shell plates of a Lancashire boiler (say for a pressure of 150 lb. per square inch) and also of the circumferential joints. What are the essentials of good riveting? (20) 3. Mention and briefly describe all the valves and cocks that you would expect to find in an underground treble-ram pump, say for a duty of 200 gallons per minute 300 feet ahead. (20) 4. An endless haulage is to be arranged on a road 1,200 yards long to transport 66 tons per hour of coal. Choosing a convenient capacity for the tub and a common rope speed, and allowing for 50 tubs over and above those on the haulage plane, how many tubs would there be in all? (20) 5. Describe the essential parts of a main and tail haulage gear driven by an electric motor of 50 b.h.p. What speed of rope would you arrange for? Do not do more than mention the electrical plant. (20) 6. Describe the Victaulic joint for pipes carrying compressed air or water. Should Victaulic joints be used for the suction range of a pump ? Give the reasons for your answer. (20) 5. — ARITHMETIC AND SURVEYING. Arithmetic. — 1. Extract the square root of 1018081 and 8.779369. (20) 2. Calculate the amount due to a miner at the end of a fortnight of 11 working days, if he produced 4¼ tons per day at a rate of 2s. 9¾d. per ton, allowing 7½ per cent, for deductions. (20) 3. A colliery produced 950 tons of coal per shift with an average wages cost of 10s. 6d. per ton. The introduction of conveyors has reduced the number of men employed by 50, whose average wage was 11s. 3d. per shift. What is the percentage reduction of the wages cost affected by the change? (20) 4. A pump raises 850 gallons of water per minute continuously from the bottom of a shaft 290 yards in depth. If the cost of pumping be one penny per horse-power hour, what is the annual cost of pumping ? Ignore the efficiency of the pump. (20) Surveying. — 5. Plot the following short survey to a scale of 1 inch = 1 chain. From A. N. 15° W. 215 links level. N. 45° E. 195 links level. S. 80° E. 300 links rising 1 in 3. S. 25° W. 170 links level to B. Find the bearing and inclination of a roadway driven on a uniform gradient from A to B. (20) 6. You are told that a roadway in a mine is rising at an inclination of 19°. Find by construction what that represents in ratio of feet vertical to horizontal. Calculate the plan measurement of a stone drift which measures 1,100 feet on the slope at a gradient of 1 in 4½. (20) 7. Describe the method of taking levels with a straightedge and spirit level. Under what conditions would you adopt this method of levelling, and what tests would you apply to your straightedge and spirit level to ensure accuracy ? (20) 6. — MINES ACT, ETC. 1. Compulsory Question. — Write, in the form of a report to your manager, a detailed description, illustrated by sketches, of the arrangements at a haulage landing with which you are acquainted. Suggest any improvements in the interests of safety. (20) 2. What are the General Regulations relating to the use of electricity (a) for purposes of signalling and (b) for firing shots? (20) 3. (a) What is meant by systematic timbering? (b) State the regulations relating to it. (c) Give an illustration of how it is applied to a conveyor face. (20) 4. What are the requirements of the Coal Mines Act, 1911, concerning (a) the lining of pit shafts (b) the provision of guides (c) the provision of detaching hooks ? (20) 5. In the General Regulations relating to the use of electricity underground it is provided that certain notices shall be exhibited where necessary. State what they are and where you consider them necessary. (20) 6. Give a concise summary of the General Regulations relating to colliery sidings and railways. (20). * Questions set at Examinations in Nov., 1930. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced, Price of official copies of questions available through H.M. Stationery Office, 1s. 6d. net. Continued from page 217, No. 14, Vol. 41.
|
|||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||