|
10th August 1929, Page: 19, Column: 2 Types Of ConveyorThree main types of conveyor were met with in the investigations of the Committee, with Mr. Robert Clive as chairman, namely, the shaker, the belt, and the scraper conveyor. Shaker Conveyors. — Shakers are admirable where there is a slight inclination in favour of the load, but are not capable of dealing with large quantities of coal up an incline. It is understood that experiments will shortly be made at one colliery with two conveyors in tandem, one of a smaller section loading into one of a larger section on a face 150 yards long, instead of a double unit. With this method of lay-out, in which one shaker conveyor loads into another shaker conveyor, the loading point is at the low side of the face instead of the middle, as with a double unit. It possesses the advantage that the whole of the gradient along the face is in favour of the load, and is an alternative to the use of a belt conveyor, which is common practice on the dip-side face of a double-unit layout where the face is inclined. A method sometimes adopted where the gradient is not too steep, is to set out the faces so that each conveyor in a double-unit dips towards the loading gate. Belt Conveyors. — Belt conveyors are working very satisfactorily at several collieries. The power they require is about half that taken by a shaker conveyor. They can be used on almost any gradient, and were seen working on the dip side of double-unit faces having an inclination of 1 in 3. The modern belt with its raised side pieces and improved return drum is a great improvement on the old-fashioned belt, upon which the coal had to be carefully placed for fear of it falling off. The time taken to move a belt conveyor forward is usually found to be the same as that required to move a shaker ; but whereas a shaker conveyor can be made to conform to any slight curvature of the face, a belt must be laid absolutely straight, as failure to keep the belt straight greatly reduces its life. Scraper Conveyors. — There are two types of scraper conveyor- namely, the Blackett and the Sectional. The Blackett was the first type of conveyor to be introduced underground in this country. It is useful for transporting coal up an incline. A drawback is that it has to be carefully positioned as it is not suitable for an undulating floor owing to the chain rising. In the latter case coal is liable to get fast under the chain ; it is broken up into small coal and sometimes breaks the chain. Sectional conveyors are used as gate conveyors in three collieries, and in two cases they deal with 210 tons and 230 tons per shift respectively. The scraper conveyor is made up in 6-ft. lengths, and can he quickly extended ; it is, therefore, particularly useful as a gate conveyor. Owing to the special construction of the chain, this conveyor can negotiate any undulations of the floor, and, unlike the Blackett, no especial Care is necessary in putting it in position. Scraper conveyors take, if anything, slightly more power than shakers. A shaker conveyor delivering down a gradient can deal With more coal than a shaker conveyor off the level, therefore, it can be longer. With shaker conveyors, the Committee are told that there is a considerable variation in the way different coals behave owing to the variation in their coefficients of friction. Regarding electrically-driven shaker conveyors the standard practice is to use a motor large enough to meet any conditions which may occur in preference to using varying sizes to suit each particular case. The information appeals to indicate that the length of conveyor is not influenced by the thickness of the seam, or whether the coal is hand or machine got. Timber Costs. An increase in timber costs in some cases may no doubt be due to the fact that in conveyor work it is necessary to keep three ranks of timber standing, so that when the time arrives to draw the back timber, a large percentage is lost owing to its being broken, gobbed up, etc. On the other hand a straight face and more regular and systematic drawing should tend to reduce timber consumption. Noting that steel supports are used with considerable success in some cases, the Committee are assured that the saving effected is by no means an exaggeration of what can no doubt be attained where similar conditions prevail, always providing a special organisation is instituted to ensure useful supervision during the installation of steel supports and afterwards.
|
|||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||