|
13th July 1929, Page: 410, Column: 1 Examination QuestionsSecond Class or Under-managers.*MINE WORKING. 1. Of the three types of longwall coal-cutters most generally in use, which is the one most suitable for ordinary conditions, and under what special conditions would you consider each of the two other types to be most suitable ? Give your reasons. (60) 2. Give detailed sketches of the temporary and of the permanent roof supports of a cross-measure drift 12 feet wide by 8 feet high which is being driven through moderately soft strata. (60) 3. An endless rope haulage is worked by a clutch from a band rope. The road is 1,000 yards long, dipping 1 in 5, with gangs of three tubs every 50 yards. Would you use a dog clutch or a friction clutch? State the weaknesses of each type. What precautions would you take to relieve the weight on the clutch at the end of each shift? (60) 4. What are the advantages and disadvantages of steel props compared with wooden props? (60) 5. On a longwall face, with a soft crumbling roof, what method of support would you adopt? Give your reasons, and illustrate with sketches. (60) 6. What points would you consider before adopting one of the following methods of haulage :— (a) Endless rope; (b) Main and tail; (c) Direct or single rope ? (60) THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine which accompanies this paper show how you would ventilate the working places. Mark the direction of each air-current; also indicate clearly the positions of air-crossings, doors, stoppings, regulators and sheets. Use the signs laid down in the Regulations. (75) 2. Sketch a ventilating fan of the Walker type, showing the construction of the fan, the direction of rotation, and the arrangements for reversing the air. (45) 3. Sketch a water-gauge as used in measuring ventilating pressures, and give a full description of its working. (45) 4. The output of coal is becoming greater than the winding capacity of the downcast pit, and it is proposed to wind coal at the upcast. State fully what arrangements are necessary above and below ground so that the ventilation of the mine should not be unduly interfered with. (45) 5. State, fully, how you would measure the air at the commencement of a separate ventilating district, on the way in, and at the faces, so as to ascertain the leakage. Give an estimate of the proportions you would get under certain circumstances. If your results were not satisfactory state how you would remedy matters. (45) 6. Sketch an air-crossing. Enumerate the various types, with a brief description of each. (45) 7. An airway is 7 feet high by 6 feet wide at roof and 8 feet at floor. With a velocity of 600 feet per minute calculate the quantity of air passing. Another airway is 7 feet high and 5 feet wide at floor lined with semi-circular steel arches, straight-sided. With the same velocity as above, calculate the quantity in this case. Give figures showing the rubbing surface per yard of roadway, of each of the two airways. (45) EXPLOSIONS, ETC. 1. How may explosions of coal dust without the presence of firedamp be caused? What precautions are necessary to prevent the initiation and propagation of such an explosion? (20) 2. How is carbon monoxide produced in mines? What are its properties? How may it be detected, and how would you deal with a person overcome by this gas until medical aid could be obtained? (20) 3. What kind of inert dust would you select for distributing on the underground roadways? How would you apply the dust, and how would you satisfy yourself that the roadways had been effectively treated? (20) 4. If the deputy or fireman reported to you as under-manager that he suspected incipient heating in his district, what would you do, and how would you proceed to investigate? If after a careful investigation, you fail to discover any signs of heating, can you suggest what may have given rise to the false alarm? (20) 5. What material would you provide and what arrangements would you make underground, so as to render prompt and efficient assistance to injured persons ? (20) 6. Sketch and describe the type of rescue apparatus you are familiar with, and explain how the oxygen apparatus differs from the liquid air apparatus. (20) MACHINERY. 1. Describe a main-and-tail hauling engine suitable for use with compressed air at say 60 lb. per square inch, the haulage plane being about 1,000 yards long. How should the engine be fenced? (20) 2. Describe carefully and in detail how you would connect a 3-core paper insulated, lead sheathed, double wire armoured cable to a motor in a situation where explosive gas might occur. (20) 3. The horse-power developed by the direct current motor of an endless rope haulage running at 2 miles per hour is 100. If the mechanical efficiency of the haulage is 75 per cent. what is the pull in the rope in lb. weight? If the motor efficiency is 85 per cent. what is the current in amperes at 400 volts? (20) 4. Two parallel steel shafts are nearly 23 inches apart centre to centre. A pinion with 18 spur teeth of 1½-inch circular pitch is mounted on one shaft that runs at 200 r.p.m. How many teeth will there be in a wheel to be mounted on the second shaft and to mesh with the pinion and at what speed will the second shaft run? (20) 5. Give a description of a sinking pump to be worked by steam or compressed air and suitable for gritty water. What type of valve and seat would you prefer for the water? The pump should be suitable roughly for 150 g.p.m. at 300 feet head with a steam (or air) pressure of 60 lb. per square inch. (20) 6. A steel shaft is 2 feet long, 4 inches diameter, turned down at one end for a length of 12 inches to a diameter of 3½ inches to form a journal for a bearing 9 inches long close to the 4-inch portion. Using a scale of one-half full size, make a side elevation of the shaft and design and draw a loose collar to fit on the end of the shaft against the bearing to keep the shaft in position. Show all dimensions necessary for making the shaft and collar. (20) ARITHMETIC AND SURVEYING. 1. Arithmetic. — A colliery using a low grade fuel for firing consumes 10,355 tons in a year. It is found that, firing with a better fuel, the quantity consumed is 6,446 tons 13 cwts. in a year. What is the relative fuel value of the two materials? (20) 2. If the number of bricks in one cubic yard of brickwork be 384, how many bricks will be required to build a square tank 30 feet by 30 feet internal measurement with 18-inch work, and 5 feet deep to the top of the concrete foundations? (20) 3. The quantity of air passing through an airway at a velocity of 560 feet per minute is 47,600 cubic feet per minute. What is the cross-sectional area of the airway and the rubbing surface per lineal yard if the height of the airway be 8½ feet and it is rectangular in shape? (20) 4. If the output of a colliery be 21½ cwts. per man per shift, what is the wages cost per ton if the average wage earned is 9s. 7¾d. per shift? (20) 5. Surveying. — The co-ordinates of a line A to B are N 480.0, E 590.0. What is the length of the line and its bearing? The bearing is to be found by plotting. (20) 6. Explain how you would make a short survey over heavy rails with a loose needle. Illustrate by giving imaginary bearings of three lines as you would enter them in your notebook. Show the correct bearings and the check. (20) 7. A road on level course strikes an upthrow fault, with a displacement of 120 feet vertical. Draw a section across the fault showing a drift rising 1 in 6 crossing the fault plane 75 feet vertically above the level. What is the length of the drift from floor to floor? Assume the hade of the fault to be 45°. Plot to a scale of one inch to 100 feet. (20) 8. Calculate the deduction per chain to reduce inclined measurements to plan measurements for inclinations of 1 in 3, 1 in 2 and 1 in 1. (20) MINES ACT, ETC. 1. Compulsory Question. — Write a report explaining the chief causes of accidents from falls of roof and sides in the face of a seam with which you are familiar. Give particulars of the seam. Explain what alterations you would suggest in the method of support. Illustrate your report with sketches. (20) 2. (a) What is a "ventilating district" as defined in the Coal Mines Act, 1911 ? (b) In the sections of the Coal Mines Act, 1911, dealing with ventilation, a definition is given of a place "in a fit state for working or passing therein." Quote it as accurately as you can. (20) 3. Give a summary of the provisions of the Coal Mines Act, 1911, and of the General Regulations as to the re-lighting of safety-lamps underground. (20) 4. Certain percentages of gas are mentioned in the Coal Mines Act, 1911, and General Regulations. What provisions relate to the following percentages :— (a) One quarter per cent.; (b) One half per cent.; (c) Two and a half per cent.? (20) 5. Explain the duties of an "Electrician" as set out in General Regulation 131. (20) 6. What records have to be kept under the Coal Mines Act, 1911, and General Regulations, respecting :— (a) Winding ropes; (b) Haulage ropes; (c) Cage chains? (20) * Questions set at Examinations in May, 1929. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Price of official copy of questions obtainable through H.M. Stationery Office, 1s. 6d. net. (For First Class questions see No. 25, Vol 39, page 388)
|
|||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||