|
29th June 1929, Page: 388, Column: 1 Examination QuestionsFirst Class or Colliery ManagersQuestions set at Examinations in May, 1929. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Price of official copy of questions obtainable through H.M. Stationery Office, 1s. 6d, net. WINNING AND WORKING. 1. In a seam of coal 4 feet 6 inches thick, with a good roof and floor, dipping one in six, it is decided to put in longwall coal-cutters and conveyors, and work on a concentrated method. Sketch and describe a continuous face where three machines are installed, and state in detail the cycle of operations for a 24-hour day. What tonnage would you expect per day, and what length of face would you suggest ? Show the drawing roads. (50) 2. How are washouts and faults respectively caused ? What is the general effect on a coal seam in the vicinity of a fault ? (40) 3. What are the advantages and disadvantages of steel props compared with wooden props ? Sketch two types of steel props. (40) 4. Give a description, with sketches, of high and low tension detonators. Row are they graded, and what tests, if any, can be applied before using ? (40) 5. A fault is met with in driving a narrow heading dipping one in five, and it is assumed to be a 20 feet downthrow. Describe in detail, with the aid of sketches, how you would prove the coal beyond the fault by means of boring. (40) 6. On a longwall face in a 6 feet seam, there are frequent roof slips or breaks parallel to the face; describe in detail, with sketches, one or two methods that you consider would be adequate for supporting the roof. (40) 7. A shaft is tubbed for the first 100 yards of its depth. A section of tubbing at a depth of 90 yards has been inadvertently cracked, and water is streaming through the crack. Explain how you would repair the fracture, and make the tubbing watertight. (40) THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine which accompanies this paper, show how you would ventilate the working places. Mark the direction of each air-current; also indicate clearly the positions of air-crossings, doors, stoppings, regulators and sheets. Use the signs laid down in the Regulations. Coal to be wound at downcast pit only. (50) 2. Sketch, in plan and section, a ventilating fan of the Sirocco type. Show the construction of the fan, and direction of rotation; also arrangements for reversing the air. State what, in your opinion, are the advantages and disadvantages of this type of fan. (30) 3. Describe an electric hand safety-lamp suitable for ordinary use. What are the advantages and disadvantages of its use ? Give an account of recently developed apparatus for indicating the presence of firedamp. (30) 4. It is desired that a ventilation survey of an extensive mine be made. State how you would proceed to do this; what instruments you would use, what observations would be made, and what precautions are necessary to ensure accuracy. (30) 5. A face of longwall workings is cut off by a large fault, and it is arranged to drive two main roads through the fault into the coal beyond. Give full particulars how you would arrange the ventilation of these roads until the working face is opened out beyond the fault. (30) 6. What is the "Equivalent Orifice" of a mine? Give an example of how it is ascertained, and discuss the purpose for which it may be used. (30) 7. What is meant by "Natural Ventilation"? How would you ascertain its proportion in the total ventilating power? Under what conditions does it become of greater or of lesser importance respectively? (30) EXPLOSIONS, &c. 1. With regard to explosions in mines, state the nature of the effects generally produced — (a) By an explosion of firedamp alone. (b) By an explosion of coal dust. How would you proceed to investigate the cause, and point of origin of an explosion? (30) 2. How may fires be caused by machinery underground ? What steps should be taken in each instance that you give prevent such an occurrence? Sketch and describe an imaginary case, stating what should be the first consideration, and the method you would adopt in dealing with the fire. (25) 3. A seam of coal, 4 feet thick, at a depth of 300 yards from the surface has been extensively worked on the higher side of an overlap fault, having a throw of 100 yards, and a hade of 30°; the workings have been abandoned, and are now full of water. Workings from another pit are approaching the fault on the lower side. What particular danger would you anticipate in these circumstances, and what special precautions would you take ? (25) 4. What are the objections to the use of certain kinds of incombustible dust? Name those which you consider unsuitable. Give approximate analyses of what you consider satisfactory samples of roadway dust — (a) When the inert material used is ordinary shale dust. (b) When the inert material used contains carbonates. (25) 5. What appliances and stores should be readily available at a colliery for rescue and recovery work in the event of an explosion or fire? What outside assistance would you call for, and how would you organise the operations? (25) 6. What precautions would you take in opening out and working a level seam of coal, 6 feet thick with moderately good shale roof, at a depth of 150 yards below the sea-bed? The measures immediately beneath the sea consist of quicksands, 70 feet thick, underlain with boulder clay 30 feet thick down to the rock head. (25) MACHINERY. 1. Electrical Section. — A 3-phase transmission line 2 miles long consists of bare copper conductors 0.2 inch diameter. The power put into the line is 120 k.w. at 2,200 volts and 0.7 power factor. What will be the drop in voltage due to resistance ? Given that the resistance of 1,000 yards of copper wire 0.025 sq. inch in area is 1.0 ohm, and that E = CR&radoc;3 where E = drop in volts, C = current in amperes and R = resistance in ohms. (28) 2. An electrical winding engine may be equipped with Ward-Leonard control and an Ilgner fly-wheel set. What is meant by this description ? Enumerate the various items of plant that are essential and give reasons for the adoption of this type of equipment. (28) 3. A centrifugal (or turbine) pump and a main-and-tail haulage are each to be driven by a 3-phase 2,000-volt 60-cycle induction motor with wound rotor. Enumerate the electrical plant for starting and controlling the motors, describing carefully the differences in the two equipments. (28) 4. Mechanical Section. — Describe a coal-cutting machine suitable for driving headings. In the course of your description mention the type of power, the overall dimensions, the weight, the means for moving from one heading to another and the precautions for safety. (28) 5. The cages in a shaft 16 feet diameter 500 yards deep are 10 feet long by 3 feet 4 inches wide overall on plan. Using a scale of ¼ inch = 1 foot, draw a plan of the shaft showing (without details) the two cages in position and the flexible conductors that you would adopt and the means for keeping the cages from colliding. Show all leading dimensions and state the diameter and construction of conductor. (38) 6. Briefly describe an overspeed and overwind preventer. State in detail the functions of such an apparatus attached to a steam winding engine. What would you regard as the worst conditions that may actually occur for the apparatus to deal with ? (28) 7. Describe in outline the plant that you would install to provide steam for a turbine of, say, 1,000 kw. output requiring steam at high pressure and high temperature. About what weight of steam and of coal (of poor quality) per hour would you expect to use ? Do not deal with the turbine nor the condensing plant. SURVEYING, LEVELLING, AND DRAWING. 1. Draw a specimen page of your level book and enter therein the field notes of an imaginary levelling from a B.M. 92.4 to a distant point and return with five instrument stations. Reduce the levels to the datum given. Show all necessary checks and say which of these you would take before leaving the field and why. (25) 2. Plot with a protractor to a scale of 1 inch to 100 feet the following short traverse made with a loose needle dial with clockwise graduation. The readings are those of the north end of the needle with the north sight of the dial leading.
Mark the bearing B to A and calculate the difference of level between A And B. (30) 3. The co-ordinates in feet of the several stations of a short traverse, relatively to the initial point, are :—
Plot the positions of the several stations to a scale of 1 inch to 200 feet, and take from the plotting the bearings of the several lines joining the adjacent stations, and the lengths of the corresponding lines. Write them as you would enter the notes of the traverse on your field notebook. (30) 4. It is proposed to work a coal seam by the pillar and stall method, leaving pillars containing 70 per cent, of the seam for surface support. Calculate the size of square pillars to fulfil the condition if the stalls or rooms are 20 feet in width. (30)
5. If, by inadvertence, you had measured a given area on a
plan on a scale of 6. A mine has a lodgment, or standage, for water equal to the feeder for 36 hours. A pump with a capacity of 450 gallons per minute pumps out of the standage. State how you would ascertain the average feeder, giving full details of the arrangements you would make, and the observations you would take for that purpose. (25) GENERAL MANAGEMENT AND MINING LEGISLATION. 1. Compulsory Question. — A district underground, under your charge, shows an abnormally large number of accidents from falls of roof and sides. You are instructed to investigate and report on the cause and the means which could be adopted to reduce the accident rate. Explain how you would proceed to investigate, and write a report on the result of your investigations. (30) 2. Section 20 of the Mining Industry Act, 1920, provides for the constitution of a Welfare Fund. Explain the provisions of the Section as to the collection, administration and objects to which the fund may be applied. (25) 3. Under the Coal Mines Act, 1911, and the General Regulations, how and by whom are firemen, examiners or deputies to be appointed ? State — (a) Their qualifications ; (b) Their duties. (25) 4. A pit is worked with three continuous shifts of coal getters at the face. How would you arrange the regular examination of the workings to comply with the Coal Mines Act, 1911, and General Regulations ? (25) 5. The General Regulations give certain instructions to workmen as to safety in getting from and to the surface and while in their working places. State what they are. (25) 6. What are the provisions in the Electrical Regulations as to electric locomotives underground ? (25)
|
|||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||