|
18th May 1929, Page: 341, Column: 1 Early History Of IronAt the annual meeting on the 2nd inst. of the Iron and Steel Institute, the new president, Prof. Henry Louis, M.A., D.Sc., assumed office. In his address he referred to the early use of iron, and said it appeared to be generally held that it was first produced in workable quantity on the southern flanks of the Caucasus, and the date assigned is usually somewhere about 3000 B.C. It is, at any rate, certain that, before iron came into use, the metallurgy of bronze was already highly developed. Articles of bronze of the Later Bronze Age show that the art of bronze-founding had already reached a high stage of perfection. The first known representation of any mechanical means for producing a blast is from the walls of the tomb of the period of Thothmes III., supposed to be from about 1500 B.C. The primitive bellows apparently consists of a flat pot covered with skin, in the centre of which is cut a hole that can be closed at will by the heel of the operator, which thus forms a valve, the skin, when released by the heel, being pulled up by a cord in the worker's hand. It is interesting to note that this identical type of bellows is still used in India by certain tribes for the purpose of iron manufacture, the only improvement in over 3,000 years being the use of a couple of light bamboos which act as springs to pull up the hide cover. Before Caesar's invasion, iron was certainly being made in the South of England, though the Brigantes in the North appear still to have been in a Stone Age. After Britain had become a Roman province, iron was made at numerous places in this country, most actively perhaps in the Forest of Dean, though there were various other important centres of early Roman iron production. The manufacture of iron continued in this country throughout the Roman occupation. The largest mass of Roman iron found in this country, if not in the world, is the mass discovered at Corstopitum, near Corbridge, in Northumberland, described by Sir Hugh Bell. Its date is considered to be between A.D. 350 and 380, and its weight was about 3 cwts. It is interesting to note that the famous iron pillar of Kutub, near Delhi, dates from about the same period or a little earlier, but weighs no less than some 6 tons, so that at that date the Eastern iron-makers were far ahead of their Western contemporaries. There is, however, no doubt that both of these masses of iron were produced by the same method, that of making relatively small lumps of iron by the direct process and welding them together. Agricola, whose well-known work is dated 1556, figures and describes in much detail the construction of a bellows with valves of quite modern type, worked by a water-wheel, and it is obvious from his description that the appliance was old enough for its details to have become standardised. It is on record that such bellows were in use at Gollnicz in 1435. A natural result of the increase in the height and power of the furnace and of the attendant higher heats thus generated was the production of white cast-iron, and it is tolerably clear from Agricola's writings that this was known in his day. Apparently one of the very earliest forms of iron castings was the iron stove plate, which originated in Germany. A sketch is known, from which a stove plate was evidently intended to be cast, dated 1474, in Nassau, though the plate itself has not been found. The oldest known cast-iron stove plate is dated 1497. In his review of the history of iron manufacture Professor Louis referred to later developments, and at the conclusion he expressed the view that the future of the metallurgy of our metal will be directed, not by the crude methods of trial and error of the past, but by the application of principles developed by the methods of scientific research. For something like four centuries this country has led the way in the great improvements in the iron industry along the old lines which have been described; we are, however, also the inventors of the science of metallography, and alloy steel, with its numerous possibilities, of which high-speed tool steel may be quoted as an example; we may, therefore, fairly claim that even in modern scientific methods we are equally leading the world in the metallurgy of iron.
|
|||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||