Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

23rd March 1929, Page: 273, Column: 1

Lubrication Of Colliery Tubs

At the February meeting of the Associates and Students' section of the North of England Institute of Mining and Mechanical Engineers, Mr. L. H. Forster, Assoc.I.M.E., read a paper on "The Lubrication of Colliery Tubs," pointing out that although lubrication is in itself an operation of small concern, and its cost is very seldom considered worthy of notice, the results obtained in all directions of coal mining can be attributed in a large measure to the lubrication system adopted as a whole. Of this system the coal tubs form a part, and in his opinion, an important part of the system to which lubrication applies. Referring to the effect of stone-dusting on the lubrication of an average pit tub, he said the liberal application of the stone dust on engine planes where the setts run at a considerable speed, neutralises the effect of the lubricant to such an extent as to require special attention. He then pointed out that lubrication, which is defined as "To supply with oil to overcome friction," Is one of the means used whereby the friction produced In conveying the material from one point to another is reduced. Friction can be defined as "An act of rubbing," When one body slides or rolls over another, and always in a direction opposite to that in which the moving body tends. Friction depends upon the pressure exerted (in the present case the weight of tub and load) and the nature of the surface in contact, and is also dependent on surface area. He described coefficient of friction as the ratio of the draw bar pull to weight of moving load kept in uniform motion on a straight and level track, and submitted a calculation showing that with an increase of 0.003 in the coefficient an increase of 10.3 per cent. is the result in the power bill.

Remarking that the calculations he submitted to the meeting only showed one item in the cost of transport due to faulty or inefficient lubrication, Mr. Forster indicated others of equal importance, and which, unlike the power bill, can be seen by any keen observer, namely : (1) Maintenance of the tubs themselves due to bent axles and consequent derailments, and wear and tear of axle and cogs. (2) Wear and tear of the expensive rope system. (3) Damage to roads and material in the roads, due to derailment, such as signal wires, cables, permanent way, timber, etc. (4) Loss of output consequent. upon such stoppages. (5) Additional wear on machinery, sheaves, etc. In addition to the above, it is generally agreed that a coal tub whose wheels commence to skid is more susceptible to derailment whilst passing over any slight obstruction, or over points, or crossing, than a tub whose wheels are revolving normally. It must be admitted, the Author said, that the actual cost of the lubricant in terms of "Cost per Ton-mile of Output" is a very small matter, but if it were possible to obtain all the above costs which would be attributed to faulty lubrication, then the plea for a more satisfactory system could be shown in a manner to command consideration.

Class of Lubricant. — The generally accepted conditions of a good lubricant were itemised by the Author as follows: (1) "Body" enough to prevent the surfaces to which it is applied from coming in contact with each other (viscosity). (2) Freedom from corrosive acid, of either mineral or animal origin. (3) As fluid as possible consistent with " body." (4) A minimum coefficient of resistance. (5) High flash and burning points. (6) Freedom from materials liable to produce oxidation or gumming. The examinations to be made to verify the above are both chemical and mechanical, and are usually arranged in the following order: (a) Identification of the oil, whether a simple oil or animal oil, or a mixture. (b) Density. (c) Viscosity. (d) Flash point. (e) Burning point. (f) Acidity. (g) Coefficient of friction. (h) Cold test.

In selecting the class of lubricant to be used at any particular colliery, Mr. Forster said that prevailing conditions, such as wet or very dusty places, should determine the quality of the lubricant and the quantity or number of applications over a given distance. the speed at which the setts run, and the weight per square inch on the axle, are other important points to consider when selecting an oil or grease. The question of speed also determines the design of the instrument used for applying the lubricant, assuming, of course, that the lubricating is done automatically. We must also remember that we are dealing with a combination of two kinds of friction, the laws of which are different, namely: Friction of Metals and Friction of Liquids (Oils). In the case of Fluid Friction, where the metals are kept apart, the friction is independent of pressure; if the pressure is sufficient to force out the lubricant or to prevent its entrance between the metals surfaces, we have solid friction. It is well known that, although a certain lubricant may give good results on an experimental test, this same lubricant would be useless when mixed with stone dust or water. A suitable oil is one with which we get the least possible friction and which will maintain a film between axle and cod under any given conditions for the greatest distance. Therefore we can say this with regard to our particular question, that the quality or usefulness of a lubricant can be measured by the distance that a tub will run with a given amount of lubricant, and which will maintain this film with the least possible friction between axle and cod under any working conditions.

In considering the type of lubricator to install, one must consider carefully the design of the tub which has to be lubricated, or if one maker competes with another, then it is essential that full details of construction be given to each. It is also important that the fixing of the lubricator be carried out as per instructions given by the maker, as each particular lubricator is designed to operate under definite conditions as regards depression, etc. If these instructions are not carried out then the results are wasted lubricant, broken parts, etc., and the multitude of faults due to inefficient lubrication.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Forster, L. H.      


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print