29th December 1928, Page: 177, Column: 1
Electric Detonators
At the general meeting in December of the Manchester Geological and Mining
Society a paper on "The Manufacture of Electric Detonators" was read
by Mr. T. Campbell Futers, in the course of which he said : An electric
detonator consists of two parts — one part consisting of a copper tube
charged with the proper quantity of explosive according to the number or
strength required, the second part being the electric firing fuse with the
wires attached for coupling up to the "firing" battery or magneto.
The detonators usually used in the coal mines of this country are of the
fulminate of mercury class, the explosive mixture consisting of 80 parts of
pure fulminate of mercury mixed with 20 part of chlorate of potash. They are
made in ten different strengths, the numbers used in mines being usually 6, 7
or 8. On the Continent number 8 is mainly used. The weight of explosive in a
No. 6 detonator is 0.0022 lb., No. 7 is 0.00331 lb., and No. 8 is 0.00441 lb.
In dealing with the weight of detonators, however, the weight of the copper
tube is always included, so that the weight of 1,000 No. 6 detonators is taken
as 4.95 lb. ; 1,000 No. 7 detonators is taken as 7.06 lb.; 1,000 No. 8
detonators is taken as 8.66 lb. These are the weights to be reckoned with when
considering storage capacity of magazines.
The manufacture of detonators is probably the most dangerous of all operations
in the making of explosives, and very great care has to be exercised,
especially when loading and pressing the fulminate into the tube. The tube is
made from the very finest quality copper, so as to stand the repeated pressings
to form the complete tube. After being pressed they are put into another
machine which accurately adjusts the length, and at the same time removes any
ragged edge at the mouth of the tube due to the original punching. They are
then washed in alcohol to remove all dirt and grease, and dried. After drying
each tube is examined by hand for cracks and defects before being passed on for
filling.
The fuse now generally used is known as the Nobel fusehead, Which was designed
to attain a high standard of efficiency and to get rid of the many inequalities
and difficulties connected with the old type. This consists of two pieces of
cardboard pasted together, each side of which is covered with a thin plate of
tinfoil.
For transport in the mine all detonators should be given out to the shot-firer
in locked boxes. The boxes should be made so that each detonator is kept
separate from the other. At a large colliery it is sometimes difficult to keep
a record of all detonators given out, and latterly many managers have adopted
the system of numbering the detonators and giving each shot-firer a number.
Every time a shot-firer gets a supply of detonators the quantity given out to
him is recorded in a book under that number, and on his return he must give up
the quantity unused. Hence should a detonator be lost and recovered in the pit,
the person responsible is easily recognised, and undoubtedly this system tends
to increase the care and thoughtfulness of the shot-firer in his handling of
detonators.
A book should be kept in the store and a record made of every delivery of
detonators, and at the end of the shift the record should be completed by
stating the number fired, miss-fired and returned, and the total should
correspond with the quantity given out.
Miss-fires are a source of danger and trouble in the pit, and no manufacturer
likes to hear that one of his detonators has miss-fired. By far the most
miss-fires are caused by: (a) Bad connection between the cable and battery; (b)
Faulty shot-firing batteries ; and (c) Damage to insulation of the wires in the
shot-hole either before putting in or after.
Shot-firing cables should be kept dry, and the ends prepared by soldering the
wires together, forming solid ends, which may be easily kept clean, and the
battery ends curved to fit easily and closely around the terminal screws.
When detonators are kept for a long time in a damp atmosphere, the moisture
penetrates the cotton covering, and creeps along until it reaches the soldered
joint, and sets up corrosion on the wire end which eventually bursts or breaks
the connection.
It is very difficult to explain "hang-fires," but it is in my opinion
a very great mistake to say it is the detonator which hangs fire. It is much
more probable to be the explosive, which owing to moisture or other reasons
does not detonate properly but burns slowly until enough heat and pressure has
been generated to explode the whole charge. It is needless to say it is most
foolish to tamper in any way with charges that have miss-fired, and boring into
an unexploded charge ought to be made a criminal offence.
The usual method of firing shots by electricity is to employ a magneto
shot-firing apparatus or battery as they are frequently termed. This apparatus
consists of an armature revolving in a magnetic field formed by permanent
magnets. The armature is revolved by a handle through gearing. The whole
apparatus is enclosed in a case, which should be "flame-proof." There
is no difference in construction between a "high tension" and a
"low tension" magneto except that of the windings of the armature. In
the former the winding consists of a great number of turns of fine wire, whilst
in the latter the winding consists of a smaller number of turns but of thicker
wire. In both cases the current generated is alternating, but in the high
tension the voltage is high, and the current small, and in the low tension the
current is greater and the voltage lower.
The question of using "high tension" or "low tension" fuses
is a very debatable one. The current required to fire a "high
tension" fuse is in the region of one milli-ampere at a pressure of 80 to
100 volts. For "low tension" fuses the current required is about 0.3
to 0.5 ampere at say 20 volts pressure. From the point of view of a magneto
firing gas it would appear the advantages lie with the high tension, as owing
to the very high resistance as compared to "low tension" there is
little chance of a dangerous spark being generated. With the "low
tension" it is much more probable a dangerous spark might be generated
where the resistance is very low, as reducing the resistance in circuit has the
effect of increasing the current generated. Again, from the shot-firing point
of view, the "high tension" has the advantage that an increase in the
resistance of the cable, and badly or carelessly made connections, may have
less effect than in the case of "low tension" fuses, as very little
extra resistance may so reduce the value of the current as to render it
incapable of firing the fuse. On the other hand, "high tension" fuses
themselves are not so reliable as "low tension," as the resistance of
the latter can be accurately measured, and for series firing are invariably
used.
Magneto exploders should be carefully used and taken care of, and no exploder
should be allowed to go on constantly in use until it fails before being
examined and tested. They should be examined and tested at least once a month,
and where they are used to fire a number of shots daily, once a week.
Shot-firing cables too should be taken care of and carefully coiled up at the
finish of each shot, avoiding kinks, which may easily cause a breakage of one
or more of the wires, thus leading to an increase in the resistance. When
working in wet places they should be frequently brought to bank and thoroughly
dried out before being used again.
In conclusion, one can easily understand when men are constantly engaged in
shot-firing "familiarity breeds contempt," but they should be taught
that "shot-firing" from charging the hole, examining the place for
gas, to the turning of the exploder handle, is a serious and dangerous
undertaking, and too much care and a strict observance of all the rules and
regulations concerning shot-firing, cannot be exercised. In the case of a
miss-shot, any deviation from the regulations regarding them should be made a
criminal offence, but unfortunately too often, such disregard means also the
loss of the lives of the persons involved.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Futers, T. Campbell | | | |