Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

15th December 1928, Page: 176, Column: 1

Electric Heading Machines

By J. H. M. Cragg, M.I.M.E.*

While for cutting of longwall faces, and, under certain favourable conditions, for cutting out of headings, the modern longwall and arcwall cutters are efficient machines, there is yet a large field for a machine which combines the efficiency of the electric motor with the adaptability, portability, and comparative cheapness of the percussive compressed air cutter. It is to fill this want that the "Siskol" electric heading machine was evolved. The electric header can be fixed to cut at any point between roof and floor, and can operate in seams down to 18 inches in thickness. Places up to a width of 20 feet may be cut from one setting. Cuts are generally taken to a depth of 4½ to 6 feet and squared up, thus leaving no irregular sides for the filler to get off. Briefly the machine consists of a column, a quadrant mounted on the column and rotated by means of a worm engaging in a toothed sector, and two arms sliding through the quadrant, supporting the motor at the back and the gear box at the front. While cutting, the machine has four movements, two controlled by the operator and two performed by the machine. The radial movement about the column is imparted by the operator, who grasps in his right hand a handle operating the worm and thus causes rotation within the range of the sector. The operator's left hand controls a feed screw, worked from near the rear of the machine, and which causes the two horizontal supporting arms to slide through the quadrant, thus imparting feed to the machine and sending the rods further into the cut. The cutting movement is essentially rotary. The main shaft, to which the cutting rods are attached by means of a chuck, rotates at 400 revolutions per minute. The power is transmitted from the motor shaft to the front gear-box by an intermediate shaft passing through the quadrant. Reduction is effected by means of gearing at each end of the shaft. The rotary movement is transmitted in the gear-box to the main shaft, with its attached chuck, rods, and bit. The driving motor is totally enclosed. It is capable of giving 3 B.H.P. continuously, and may be either A.C. or D.C. according to the power available. The motor is connected by means of a 12ft. flexible cable to a switchbox starter, which controls the motor. The cable is firmly fixed at the motor end, and forms part of the machine. At the other end it is fitted with a plug, which fits into the starter. Owing to the low weight of this machine (7 cwt.) flitting is not a difficult operation. To facilitate the operation a steel plate is attached to the bottom of the column. To this plate are attached two axles with wheels set to the track gauge. The wheels are held in position on the axle by pins, and are thus readily removable. When a cut is about to be made, the machine is run on the track to the face of the heading, timber inserted above the column and below the base plate to take up the pressure, and the tightening screw on the column screwed up.

The electric heading machine is designed to meet certain definite conditions. Its main use will be found in cutting out headings where bord and pillar methods are employed, or wherever advance headings have to be driven in coal. Under such conditions mechanical cutting will generally be found to give a more rapid rate of advance than hand hewing, together with an increase in output per man, a reduction in getting cost, and a decrease in the amount of slack made. The adaptability of the heading machine renders it particularly useful for cutting in broken and faulted ground, where it can be readily handled without disturbance to roof supports. Further incidental uses will be found in cutting out the corners of longwall machine faces, where this is deemed advantageous, and in cutting out the fast corners on hand got faces. The electric machine is readily flitted on the ordinary track laid by the fillers, and needs no elaborate preparations at junctions.


* From paper on Notes on an Electric Heading Machine read at November meeting of the Associates and Students' section of the North of England Institute of Mining and Mechanical Engineers.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Cragg, J. H. M.      


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print