Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

17th November 1928, Page: 140, Column: 1

Diamond Boring

In a paper which he had prepared for the October meeting of the Associates and Students' Section of the North of England Institute of Mining and Mechanical Engineers, Mr. F. E. Smyth took for his subject "Diamond Boring Applied to Tapping Drowned Areas Underground." The bore-hole forming the subject of the paper was put up vertically from the Beaumont Seam of Follonsby Colliery to the Hutton Seam of Springwell Colliery, a distance of 154 feet, to tap a large body of water in the latter seam at an estimated pressure of 170 lb. per square inch at the bottom of the bore-hole. In consideration of the enormous quantity of water overhead and the high water pressure anticipated, extensive precautions were taken to ensure the safety of the borers and complete control over the water when tapped. The boring was carried out on contract by Messrs. Andrew Kyle and Company, of Galston, the system of diamond core boring being adopted. Core boring, as the name implies, is the drilling of a hole in the earth and bringing to the mouth of the hole a core from the centre showing the strata passed through.

From the paper prepared by Mr. Smyth we append general extracts :—

The drill consists of a line of hollow rods from the bottom to the top of the hole (or vice-versa when boring downwards), through which water is forced and rotated either direct or through gearing from some source of power. The bit or cutter is at the top end of these hollow rods and does the cutting. The bit (in this case a diamond crown), which is hollow, cuts or wears a circular groove in the strata, leaving the centre solid, and when continuous drilling is maintained this centre core passes downward through the hollow bit and is retained in the core tube. When the core tube is full, the drilling stem is withdrawn from the hole and the core extracted from the core tube. Successive cores laid in line enable one to see at a glance what strata have been passed through in the course of the boring.

The diamond system of boring was first introduced in 1870 by Major Beaumont, and the diamond crown head is the oldest and best known of all core forming drills. The bit consists of a hollow cylindrical steel crown, the diameter of the hole to be drilled, and about six inches long, with diamonds embedded in the rim. The stones are set in pairs, one stone of a pair being diametrically opposite, and in the same corresponding place as the other, so that no part of the area to be cut will fail to be touched by the diamond at each revolution of the bit. Sizing stones or reamers are placed on the outside of the crown for sizing the hole, and although those latter do no actual boring, they are necessary for maintaining the size of the hole. Great care is necessary in setting the stones, it being especially important that they have such clearance that the metal of the bit does not come into contact with the rock.

For setting the stones, cavities are cut in the metal of the bit and shaped for each individual stone. The stones are set so that their cutting surface slopes away from the direction of rotation of the bit. The number and size of stones vary with the diameter of the hole to be drilled ; in a 3-inch diameter bit a common number is eight cutting stones and four reamers ; in a 6-inch diameter bit twelve cutting stones may be used and four reamers.

Of the diamonds used in boring, there are two distinct varieties, (a) Carbon, a massive form of pure carbon compact in structure and without cleavage, S.G. from 3.1 to 3.3, commonly known as opaque or black diamond, being pure black or blackish grey in colour. It is very hard, harder even than the clear crystal, and an ideal stone for boring purposes, but it is very expensive. (b) Bortz are imperfect or flawed specimens of the clear crystal such as are unsuitable for jewellery, but are used for commercial purposes, the chief of which is boring. It is of confused crystalline structure and its rough irregular form renders it unsuitable for drilling very hard rock, being difficult to set, and it wears unduly on account of the breakage of the projections.

The core tube is made of mild steel tube ¼ inch thick, 6 feet 6 inches long, and inside diameter to suit the diameter of the core required, the size of the core being equal to the diameter of the hole less the thickness of the rim of the crown. The core tube has an inside thread at both ends, at the top for connection with the bit and at the bottom to screw on to the reducing plug. The reducing plug is of solid steel turned to a smaller diameter at the top end, where it screws into the core tube. It is bored longitudinally with a 1¼ inches diameter hole, to the top of which is fitted a small perforated strum protruding inside the core tube, and in the bottom is a reducing ferrule for connection to the hollow boring rods.

The bore rods are of steel, 1 inch inside diameter and If inches outside diameter in 10-feet lengths. Each rod has about 2½ inches of inside square section thread and joined with an inside nipple, thus making a flush joint. The use of square section threads facilitates the quicker screwing and unscrewing of the rods when occasion necessitates. If the common V-section thread were used the torque in the boring stem would so tighten each joint that much time would be wasted in disconnecting the rods.

In upward boring the stem must be strong enough to resist the upward thrust exerted by the drilling machine at one end, and the resistance of the face of the hole at the other end, together with the total weight of the whole line of rods which increases as the hole proceeds. It is safer then to err on the side of the heavy rather than light rods. If the latter are used they are liable to buckle, which gives rise to vibration, or back lash, so setting up such frictional resistance that it is impossible to advance the cutter against it.

The boring head itself is of the rack and lever type, and is supported on ball bearings with hardened steel races. The lever is attached to a small pinion wheel supported on a spindle between two lugs cast on the body of the machine which in turn engages with the teeth of the rack of the boring stem. By moving the lever up or down the boring stem can be raised or lowered as required ; by hanging a weight on the lever a constant pressure is maintained on the face of the hole. This pressure may be increased by either increasing the weight, or moving the same weight further along the lever, away from the machine. This becomes necessary as the hole proceeds and the extra rods give an added weight downwards on the boring stem.

The arrangement gives a very fine adjustment of feed ; the rack and lever are also capable of raising or lowering the entire drilling stem if choking of the crown should take place while boring. A safety pawl is fitted to the front side of the rack, and supports the weight of the boring stem when it is required to obtain fresh purchase with the lever. The boring head is bored longitudinally to allow passage for the cooling water, and has a union joint at the bottom for connection to the flexible hose pipe from the circulating pump. The wheels of the machine rest on rails securely packed from the floor and dead level. Attached to the bottom members of the frame are two rail clamps, one for each rail, and when the machine is run into position for drilling these are screwed down to grip the rails, making the machine body immovable.

The motive power is applied to the fly wheels, which are crowned, and is then transmitted to the boring head through skew-gearing suitably encased in the body of the machine and running in grease. The spokes of the fly wheels are drilled for the purpose of fitting hand crank levers in the event of it being desired to drive the machine by hand. Although many holes have been satisfactorily drilled by hand using this type of machine (the maximum depth being about 800 feet drilling downwards, a much less arduous proceeding than upward boring), mechanical means of drive are in all ways preferable. Hand drilling usually means hand pumping, and, incidentally, more men are required on the job, together with the added disadvantage that progress is much slower.

As a rule in diamond boring the speed of actual cutting is faster in soft rock than in hard, but hard uniform rock that cores well drills faster than very soft strata that clog the bit or grind up in the core barrel. Generally speaking the rate of advance is higher in uniform rock than in alternating hard and soft strata, and low in shattered and fissured rocks.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Beaumont, —, Major      
Smyth, F. E.      



Links to Collieries/Mines mentioned in this article

 

Follonsby Colliery  Follonsby Colliery
Springwell Colliery  Springwell Colliery


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print