|
28th July 1928, Page: 11, Column: 2 Examination QuestionsSurveyors.*FIRST PAPER. 1. A vertical bore cuts the base of a stratum 15 feet in thickness at a depth of 135 feet. The bore core shows the dip of the strata to be 80 degrees. The surface rises at a uniform grade of 1 in 7 in the same direction as the strata. Calculate (a) the thickness of the stratum measured at right-angles to the bedding; (b) the distance from the bore to the outcrop line of the top of the stratum, and the breadth of the outcrop of the stratum — both on the slope of the surface. Check your answer by drawing a section on the line of dip and rise on a scale of 1 inch to 100 feet. Assume 10 feet of alluvial deposit on rockhead. (12) 2. The plan (in First-Class Colliery Managers' Examination) shows spot levels. Transfer these levels neatly to your answer book and draw contours at intervals of 5 feet vertical as accurately as the information on the plan will allow. Take the lowest contour at 65 feet. (8)
3. Construct a scale of 4. A pond is to be formed 50 feet in diameter and 8½ feet deep, inside dimensions. The bottom of the pond is to have a bed of concrete 12 inches thick. The wall is to be built of brickwork 18 inches thick. Calculate the excavation, allowing 3 inches of clearance at the circumference, and the quantity of concrete and of brickwork. State the approximate number of bricks required. (8) 5. Give the symbols used on geological survey maps to indicate (1) faults ; (2) dip ; (3) horizontal strata ; (4) site of a borehole (5) site of an abandoned shaft; and (6) mouth of an adit, mine, or day level. Mention any indication (apart from a dip marked on the plan) by which the direction of dip can be determined by the line of an outcrop in relation to other surface lines. (12) SECOND PAPER. 1. The co-ordinates of five points, A, B, C, D and E, in links, are :— (A) N. 0, E. 0; (B) N. 332, E. 270; (C) N. 1176, W. 85 (D) N. 810, E. 815; and (E) S. 318, E. 655. Calculate the area of the closed figure A, B, C, D and E without plotting. (12) 2. A pole carrying an electrical power line, erected on the ridge of a building, is to be renewed. Its length cannot be conveniently got by direct measurement. How would you determine the length of pole required? Give any sketches necessary to illustrate your answer, but do not give details of the manipulation of instruments used. (12) 3. A fault bearing 72°30' N.E. and S.W., has been exposed in a working, dipping due east 1 in 6, at two points, A and V, on opposite sides of the fault. The co-ordinates of A and B are A = N. 1,101, W. 1,280, level at A 982.3; B N. 1,221, W. 1,098, level at B 879.6. Find, by calculation, the vertical displacement of the fault at B, and the bade of the fault. (8)
4. Write a short description of an eidograph, and explain the
principle on which it is constructed. To what figure should the
verniers be set to reduce a plan from a scale of 5. The pillars in a pillar-and-room working are 30 yards square and the rooms 12 feet wide. What proportion of the seam has been taken out ? If it be desired to reduce the percentage of the seam left in pillars to 62½ per cent., what width of a room would it be necessary to drive through each pillar? (80) 6. Sight rails or crossheads are to be fixed at A and B, 20 chains apart, on the line of an embankment of a railway siding in course of construction. The formation level at A is 224.75 and the gradient from A to B is to be a fall of 1 in 80. Starting from an Ordnance Bench Mark on a level of 207.8, the successive readings of the staff in taking flying levels towards A are 12.82, 3.76, 11.83, 2.11 and 10.73. What must be the next foresight reading on the staff held on the sight rail at A? Give assumed readings of the staff, continuing the levelling to B so as to fix the cross rail at B at its proper level. (12) 7. The following particulars are taken from an underground traverse :— D to C, 442.5 feet. N.68°25'10"E.; C to B, 437.0 feet, S.51°9'20"E. ; B. to A, 4282 feet, S.78°58'30"E. It is proposed to drive a road in the line of AB, starting from CD. Find the starting point, and the angle that should be set off from CD in order to drive towards B. Check by plotting. (8) * Questions set at Examinations in May, 1928. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Complete sets of questions available through H M. Stationery Office, 1s. 6d. net. (For First Class Questions see No. 26, Vol. 38.)
|
|||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||