14th July 1928, Page: 408, Column: 2
Monocable Aerial Ropeways
By E. C. Bowley.
[At the April meeting of the South African Institution of Engineers
Mr. E. C. Bowley presented what was described as a somewhat novel paper on
Monocable Aerial Ropeways, in which he described the installation on the
property of the Lydenburg Platinum Areas at Maandagshoek. Below we reproduce
from the Institution Journal some general remarks on this system of ropeway.]
Aerial ropeways are becoming more recognised as a profitable means of
transportation, and their adoption has permitted the working of many mining and
other propositions that would probably otherwise have remained undeveloped and
unproductive. This is due to the economic and convenient application of this
system of transport to mountainous country. Aerial ropeways may be mainly
divided into two classes, viz. : (1) The bi-cable or two rope system. (2) The
monocable or running endless rope system. The bi-cable system, although having
a continuously moving rope for hauling the loads, is also provided with a
separate rope for acting as a track or rail on which the loads travel.
The origin of the monocable ropeway is by no means new, being invented by
C. Hodgson about the year 1868. Unlike the usual bi-cable and telpher
ropeways, this system is characterised by having only one rope, which serves
both to support and transmit the load. It can be applied with advantage where
the material to be transported does not exceed 100 tons per hour, provided that
the tonnage can be conveniently sub-divided into individual loads of not more
than 30 cwts. This is due to the double duty the rope has to perform. It is
inadvisable to have the gradient of the rope exceeding twenty degrees. This
does not infer that this system is not applicable to hilly country. The profile
of the cableway is never parallel to the contour of the ground, so that,
provided the configuration of the country suits the arrangements of the spans
between supports, the monocable can be adapted to very rugged and hilly
districts. In cases of long ropeways, these can be built up of units, having a
length of from four to ten miles maximum, so that a ropeway having a length of,
say, twenty-four miles might possibly be built in three sections. The loads
would pass through from one section to the other on shunt rails at the
stations, which are built at the junctions of the sections.
The advantages of ropeways can be summarised briefly as follows : (1) The
ropeway can be taken in a straight line from point to point and need not be
diverted on account of any irregularities of the ground. (2) Embankments,
cuttings, bridges and tunnels are unnecessary, and the installation may be
speedily placed in operation when required. (3) The cost of a ropeway, over
rough country, is much less than any other means of transport. (4) The unit,
when in operation, does not require skilled labour. (5) The upkeep and
maintenance charges are exceptionally low.
The monocable system of transport consists of an endless wire rope supported
upon a series of pulleys mounted on suitable structures, such as towers or
standards, located from three hundred feet to five hundred feet apart,
according to the contour of the ground. The rope passes at one end around a
drum or surge wheel, power being transmitted to this wheel through a series of
gears, as practised in mechanical haulages. The tension wheel is usually at the
other end, and is mounted on a travelling frame, which, in turn, is attached to
a balance weight. The loads are carried in side-tipping buckets, suspended from
the rope by means of a carrier, the design of which enables the bucket in
transit to clear the supporting wheels. At each terminal a frame supporting a
shunt rail is placed, which receives and supports the carrier of the bucket
when disengaged from the rope.
The greatest possible care should be exercised in placing the profile of the
hypothetical line of the cableway relative to the contour of the ground. A
sudden rise in the fine of cableway is apt to cause trouble. The varying
tension and deflection of the rope in operating the unit is considerable, and
when there are no loads in the immediate vicinity preceding a sudden rise
little deflection of the rope is caused, so much so that it may lift and rise
above the supporting pulleys at this point, thus causing disengagement of the
carriers of the oncoming buckets. The conditions of an installation vary so
considerably that this problem would have to be left to the designer of a
specific layout. The correct spacing and placing of supports or towers will
generally assist in overcoming this difficulty. An unavoidable drop in the line
will subject the affected supporting pulleys to additional stress. The wheels
in this case should be compounded. Moreover, in determining the positions of
the towers, endeavour must be made to take full advantage of their height by
having a maximum clearance between the bucket and surface of the ground with a
minimum tension on the rope. No definite ruling can be given as to the spacing
of the towers; as previously mentioned, this varies with the configuration of
the ground and the size of the unit installed. Accuracy in surveying and
plotting the positions of supports cannot be too strongly emphasised. The
direction of the cableway must be perfectly straight.
Similar to the usual procedure in preparing foundations, provision should be
made for final alignment and grouting of the supports. For this reason the legs
of the supports should have a means of travel of at least six inches when in
foundation sockets.
When designing a tower it is advisable to spread the legs at the base, so that
when a bucket is passing over the tower the total weight comes within and is
distributed over the four legs. This gives a better distribution of the load
over the foundations concerned. Where there is a scarcity of water and
transportation is difficult, this is a factor of importance, as foundations can
be reduced to a minimum with a broad base tower. The component parts of the
tower are usually transported to and assembled at their respective positions.
For convenience, the legs, stiffeners and cross-arm are usually bolted
together. The bolt-holes of the cross-arm should be slotted so as to assist in
the final alignment of supporting pulleys.
The mountings of the pulleys or sheaves are allowed to pivot on the cross-arm
pin. By this means the pulleys are in balance ; the advantage of this is that
it causes a compensating effect at the apex of support, and thus reduces the
bending stresses on the rope. Moreover, the elevation of the pulleys varies
with the position of the load as it passes by the tower, thus preventing
disturbance of the saddle grips on the rope and at the same time increasing the
clearance for the carrier in passing through the sheave. By this compensating
arrangement, the pressure is evenly distributed over the bearings of the
sheaves, shocks are diminished and the life of the wearing parts is increased.
The supporting pulleys or sheaves are made of cast steel and are light and
rigidly constructed. The flanges of the sheaves are slightly dished, and, in
the centre, there is a groove for receiving and guiding the rope, the depth of
which engages about one-third of the rope diameter. This design of sheave
enables the grip and carrier to pass freely when in position on the moving
rope. Should the rope become displaced, it is so guided by these flanges as to
resume its correct position in the groove or tread. The sheave wheel bearing is
of the usual parallel roller type, the spindle of which has a central passage,
and, by means of a grease gun, the lubricant is injected. This type of bearing
has proved satisfactory, insomuch that of the four hundred that have been in
daily operation for the past year only ten have been replaced.
The carrier consists of a cast steel mounting, to which is attached a set of
small wheels for the purpose of moving the bucket on the shunt rails at the
terminals. Centrally placed in the mounting there is a triangular-shaped slot,
which receives and permits the hanger-arm to pivot. This enables the bucket, in
travel, to be horizontally as the carrier varies its inclination with the
elevation of the rope. The stems of the saddle grips are inserted in the
mounting at two points central to the hanger-arm, sufficient play being
provided to enable the grip to take a true and aligned position on the rope.
Upon the success of the saddle grip depends the economic and efficient running
of this unit. The grip should be simple in construction, certain in action and
designed to produce as little wear as possible. Transporting loads on gradients
exceeding one in four with a, saddle grip that does not require external
assistance in effecting a hold on the rope is still an engineering problem.
The rope forms a very, it not the most, important part of the monocable, in
view of the heavy duties it has to perform, being both the chief wearing part
and the most costly to renew. The behaviour of such parts as might
detrimentally affect the life of the rope should, therefore, be carefully and
regularly observed. A few general observations upon the class of rope most
suitable for this purpose may prove of interest. Lang's lay 6/7 flattened
strand has proved most serviceable. The compound, applied to the rope during
construction, is sufficient to lubricate and prevent internal corrosion of the
rope for a period of at least two years. In tropical climates, where the rope
is exposed to the heat of the sun, a portion of the lubricating compound leaves
the heart and overcoats the surface of the rope. The lubricant in this state is
a source of danger, as it may cause the slipping of the saddle grip when
surmounting a gradient. When ordering a rope for a specific layout subjected to
these tropical conditions, this point should be emphasised for the purpose of
obtaining a compound, the constituents of which are not readily affected by the
heat of the sun. As few splices as possible should be made. This is usually
governed by transporting facilities available for heavy material, and the
method adopted in drawing the rope over the line of cableway. Moreover, when
splicing, as the tucking-in of the strands replaces the hemp core, the
resilience of the surrounding strands is so affected as to cause the surface of
the wires to wear sooner over the area of splice. The stretch of a new rope
over a length of seven miles is considerable, as in the case of the unit in
question. To avoid constantly cutting and resplicing at the early period of
operations, due to the stretch in a new rope, the tension frame should have a
means of travel of at least 1/200 part of the length of the cableway.
Although the minimum tension on the rope is governed by the balance weight, the
tension so caused is not uniform, but changes at varying points relative to the
driving unit and with the elevation of the supports. The travelling buckets
themselves alter the tension on the rope, by varying the amount of sag between
spans, and thus take up the minor changes in the tension due to the elongation
or contraction. From these and other causes the sag in the rope may become of
such magnitude as to require adjustment of the tension balance. As a useful
adjunct on ropeways of two or more miles in length, a sag indicator, fastened
to one or more buckets on the circuit, gives timely warning of the necessity to
attend to adjustment of the rope tension. It may be thought that the balance
weight would automatically adjust the differences in tension, but in practice
it is found this is not so, as, owing to friction at the supports and in the
system generally, the energy required to overcome this and maintain the desired
tension on the rope is not sufficiently supplied by the balance weight at the
terminal. Although the balance weight is insufficiently sensitive to respond to
the minor changes in tension, it acts as a safeguard against undue stresses
being placed on the rope.
The surge wheel for driving the unit is usually placed at the extreme end of
the unloading terminal, and, by supporting the rope in suspension, the required
tension is obtained, so enabling this wheel to transmit the motive power with
two full turns of the rope and avoid slip. The gears for driving the surge
wheel are arranged within the supporting structure, and these are, in turn,
belt driven from the power unit.
An economical rope speed has proved to be 3¼ miles per hour. The carrying
capacity of the line can be increased by simply placing a larger number of
buckets in circuit. Increasing the speed of the rope means additional friction,
the amount of which is considerably greater than that caused by installing more
buckets.
There is a light steel structure at each station, on which the shunt rails are
mounted. Attached to this structure is a series of pulleys for guiding the rope
into position, so as to effect a transfer of the carrier to and from the shunt
rail.
At the point at which the transfer of the carriers is made, i.e., from shunt
rails to rope and vice versa, the gauge between rail and rope should be
identical to the gauge of the small wheels and saddle grips attached to the
carrier. This is important, as a difference of a quarter of an inch is likely
to cause misengagements and detachments of the carrier. The shunt rail also
should be adjustable at this point, as the gauge gradually changes owing to the
supporting pulleys of the rope attached to the structure becoming worn.
Moreover, this rail should be set at an angle slightly less than that of the
rope. This permits a safe and correct transfer of the carrier from the rope to
the rail, and eliminates shocks that would otherwise be caused to the carrier.
In transferring the carrier from the shunt rail to the rope, a flying start is
given to the load. To assist this operation, the rail at this side of the
terminal should have a slight downgrade.
In long ropeways the starting torque is considerable, and provision for this
should be made when deciding the class of driving unit to use. To facilitate
constructional and working operations, it is advisable to have a means of
communication between the stations. A telephonic installation is preferable to
any system of signalling, as it is of general utility apart from that of the
ropeway.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Bowley, E. C. | | Mining Engineer | |
| Hodgson, C. | | | |