|
19th May 1928, Page: 345, Column: 1 Some American NotesCoal Statistics. The leading bituminous coal producing State in America in 1927 was West Virginia, with 151,680,000 short tons. Throughout the previous history of the industry Pennsylvania has ranked first, but last year the production of this State was 131,007,000 tons, though of course the output of the anthracite mines (80,652,000) raised the grand total to 211,659,000 tons. Kentucky had a busy year, securing third place with 72,626,000 tons, Illinois ranking fourth with 45,408,000 tons. Following in order as coal-producing States were Alabama, Indiana, Ohio, Virginia, Colorado, and Wyoming. The Bureau of Mines reports that 759,000 men found employment in 1926 at the mines of the States, of which number 637,000 laboured underground. In American bituminous mines the daily output per worker averages 4.5 short tons, the average in the anthracite mines being 2.09 tons, this drop being accounted for by more difficult geological conditions. Nearly 72 per cent. of the bituminous coal is cut by machine, whilst nearly 17 million tons are mined by steam or electric shovels in open pits. One strip pit in Montana reported to the Bureau an output of 48 tons per man per day. Indiana Coal Mining. According to State Geologist W. H. Logan, the coal-bearing area of the Indiana coalfield includes approximately 7,000 square miles, or about one-fifth of the total area of the State. There are twenty beds of coal in the State, all the coals belonging to the bituminous class, three kinds being recognised, block, cannel, and common bituminous, the greater part of the coal being of the latter type. As indicated in the U.S. Bureau of Mines statement, the mining systems are the ordinary room-and-pillar and the panel room-and-pillar. In small areas in a few mines longwall has been used a little. In recent years the panel system has been used more extensively. The mine openings include open pits, drifts or inclines, tunnels, and shafts, the latter being used where the overburden is more than 60 to 70 feet thick, or in some places where the overburden is thinner but the roof is good. The deepest shafts do not exceed 450 feet. Most of the mines are dry or contain only a small amount of water. Artificial ventilation is obtained by means of electrically-driven fans at the air shafts. The majority of the mines contain little gas, and explosions are rare. The annual coal production in Indiana approximates 22 million tons. Falls in Mines. In connection with the investigation of the subject of falls of roof and coal in coal mines, the United States Bureau of Mines has made a compilation of the laws of the various states relating to coal-mine timbering. The report, known as Technical Paper 421, is by J. W. Paul and J. N. Geyer. A perusal of these laws shows that the mine foreman is made the custodian of his miners' safety at working places and in going to and from working places so far as that safety concerns the proper and safe support of the roof. A study of the statistics of accidents shows that the State having the best mine-timbering law, does not necessarily have the lowest accident rate. The degree of execution of the requirements of the law or absence of specific law or regulations is an index of the accident rate for any given State or district of the State. The accident rate is higher in States and districts where there has not been an organised programme involving systematic methods of timbering, inspection and close supervision. The majority of the State laws have the following salient features : The owner, operator, or mine superintendent shall furnish the necessary timber, props, and caps and keep them always available for the use of workmen The mine foreman shall have timber, props, etc., delivered near the place where they are to be used, generally at the place where empty mine cars are delivered. The mine foreman shall visit each working place at regular intervals to see that the laws and rules are being observed, and he shall not permit any person to work in a dangerous place except for the purpose of making it safe. Miners shall examine the roof in working places before beginning work and shall pull down any loose or dangerous roof material or make it safe by using timber. Where the necessary timber is not available miners shall vacate the place. Mine Safety Records. What is known as the Joseph A. Holmes Safety Association in the United States makes awards of medals and certificates for personal deeds of bravery and meritorious safety achievements in mine working. At the recent annual meeting some commendable records were revealed. The Stewart Mine at Southwest, Pa., which employs more than 250 hands, experienced no fatality or accident entailing permanent or partial disability over a period of seven years, nearly three million tons of coal being mined. The Logans Ferry mine, at Logans Ferry, Pa., employs 400 men and mined over two million tons of coal in a period of 4½ years without the loss of a single life. Among other notable records may be instanced the Negaunee mine, Negaunee, Michigan, where 26,600 days of labour have been performed since the occurrence of the last minor accident, and no fatal accident occurred in a given period of eight years comprising more than 590,000 days of labour. Educational Industrial Films. A feature has been made by the U.S. Bureau of Mines of educational industrial motion picture films, the Bureau having more than 600 sets of films, aggregating 1,830,000 feet. These films show the different steps in the production, treatment, and utilisation of the essential mineral materials or make plain the safe methods of mining and preparing minerals. The films are loaned to schools, colleges, miners' unions and other organisations interested in public welfare, the cost of transportation being the only charge made. Among the half hundred Bureau films available for free use we notice the following titles : Story of Coal; Saving Coal at Home ; Story of Rock Drilling ; Story of a Storage Battery ; Whan a Man's a Miner ; "Play Safe" ; Story of Power ; Story of Dynamite ; Twelve Points of Safety; First Aid or the Care of an Injured Miner by a Miner; Oxygen Breathing Apparatus ; Story of a Rock-dusted Coal Mine ; Story of an Electric Detonator. Slate Quarrying by Wire Saw. What is known as the wire saw has been used to a limited extent in European countries, but the novel expedient of using it for the cutting out of huge masses of slate, as reported by the United States Bureau of Mines, promises to result in the elimination of great waste in the slate quarrying industry. Tests showed that this method of cutting by abrasion rather than by disruptive forces, as in the use of explosives, or by the chopping action of the channelling machine, was found to eliminate practically all of the excessive waste directly attributable to these methods. The statement made is to the effect that the wire saw is essentially a three-stranded wire cable running as an endless belt. This cable takes the place of the saw blade and the teeth of the saw consist of sand grains carried in the spiral grooves formed by the winding of the wire strands. The saw cable is carried and guided by means of orienting pulleys from the driving unit to the particular place in the quarry where the cut is desired. Here the wire is brought in contact with the slate, and is drawn across it while held forcibly against it. Sand is automatically fed to the saw by means of trough-shaped boxes using a small stream of water as a conveyor. As the sand is carried against the moving cable it is caught in the grooves and carried along. The sand is thus forced against the rock and dragged along with the cable, wearing away the rock particles where the pressure of the wire is exerted. This results in rapid abrasion, forming a cut about one-fourth inch in width, which is a little wider than the diameter of the cable. Accepting the authority of the Bureau, slate, which is a very condensed siliceous rock, is cut at a very rapid rate by means of wire saw. In making a cut 80 feet in length it was found that the wire would sink at the rate of a little more than 2 inches an hour, completing a cut 8 feet in depth in 45 hours, or five 9-hour days. A cut of the same size by old methods would require about two weeks. The wire, it is explained, wears remarkably little. A wire 800 feet long, on completing a cut 80 feet long and 8 feet deep, — that is after cutting a surface area of 640 square feet, — was found to be reduced in diameter less than 1/32 inch. Another great advantage claimed is in cost production. The cost by the new method is approximately one-half that involved in methods formerly employed, and those conducting the tests anticipate further reductions when the wire saw method is more fully perfected.
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||