Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

28th January 1927, Page: 214, Column: 1

Examination Questions

Second Class.*

MINE WORKING.

1. In a seam 5 feet thick, dipping 1 in 6, with hard coal and a bad roof, it is decided to drive a heading 9 feet wide to the dip with the aid of a percussive machine fixed on a column. Show by sketches how you would fix the column and how you would timber right up to the face. How long would you expect it to take (a) to fix the column? (b) to hole to a depth of 5 feet? (c) to get the coal down? (60)

2. Show in detail how you would arrange the tub roads at the bottom of a shaft for a large output so as to deal with the tubs with as little manual labour as possible. (60)

3. A hole has to be bored vertically upwards for exploration purposes. It is expected to go about 15 yards. How would you carry out this work? (60)

4. What advantages are claimed for girders of a circular type over other types of support for underground roadways subject to severe crushing? How would you set these girders? (60)

5. Two main roads of equal size crossing each other at right angles are to be lined with brick arching. Explain how you would carry out this work, and state whether you would prefer to adopt some other method of support at the actual crossing and, if so, why ? (60)

6. Sketch and describe the arrangements you would make for ventilating a shaft in course of being sunk. (60)

THEORY AND PRACTICE OF VENTILATION.

1. On the plan of a mine which accompanies this paper show how you would ventilate the working faces by means of five separate air-currents (splits) and four air-crossings. Show the direction of each air-current and the positions of air-crossings, doors, stoppings, regulators and sheets, and avoid placing air-crossings in positions in which they would obstruct the haulage. (60)

2. State the reasons, if any, why a fan driven by a steam-engine or electric motor ought to be more efficient than the old fashioned furnace. Describe any appliances, other than furnaces or centrifugal ventilators, suitable for producing a current of air in a mine. (50)

3. Make a detailed sketch of a regulator. Show how its aperture may be made larger or smaller. Calculate what quantity of air will pass through it when its opening is 2 feet 6 inches square, and the difference of pressure on its opposite sides is equal to a column of water 2 inches high, and the weight of a cubic foot of air is 0.08 pound. (50)

4. The quantity of air passing through a mine is 60,000 cubic feet per minute when the fan is developing 100 horse-power. What quantity will pass through the same mine when the fan is developing 225 horse-power? (50)

5. Sketch and describe the construction of a Waddle fan. Show the direction of curvature of its blades. (50)

6. Make a sketch of an air-door showing particularly the construction of its binges, the details of the frame which supports it, and how the door and its frame are connected to and form a part of the partition which blocks the air in the roadway in which it is built. Pay special attention to the means of preventing the air from escaping at the points where the closed doors stand immediately over the rails. (50)

7. Specify exactly what are the objects aimed at in "splitting" the air. Given one airway of a certain length through which 10,000 cubic feet per minute of air are passing at a water-gauge of one inch, what would be the water-gauge if the same total quantity of air were passed through two airways each of the same dimensions as the one? (50)

EXPLOSIONS, ETC.

1. Sketch and describe a mechanical appliance suitable for the distribution of inert dust in the workings of a dry and dusty mine. Describe the manner in which inert dust is applied in any dry and dusty mine known to you. (20)

2. What precautions would you take when sealing off a district in which a serious case of spontaneous heating has taken place, particularly with regard to the safety of the men working at the stoppings? (20)

3. Name the materials which are liable to ignite easily, or spontaneously, that are in common use in coal mines, and state what precautions should be taken to prevent such dangers. (20)

4. Which in your opinion is the best method of rendering coal dust harmless? How would you determine when the necessary degree of safety has been reached, and how would you maintain it? (20)

5. What precautions are necessary before commencing to restore the ventilation of a mine in which an explosion has occurred? (20)

6. The analysis of a sample of dust taken from the main haulage road of a mine is as follows Moisture, 2.00 per cent. volatile matter, 28.00 per cent. ; carbon, 31.00 per cent.; ash, 3900 per cent.; = 100.00 per cent. Do you consider this a satisfactory state of affairs? Give reasons for your answer. (20)

MACHINERY.

1. State what is meant by the words in italics in the following description of an electric switch : The switch is of the 3-phase oil-break, loose handle type with automatic overload releases and time limit fuses in 2 phases and a low volt (or no-volt) release in the third phase. (20)

2. Describe an electrical centrifugal (or turbine) pump for a sinking-shaft. (20)

3. Give a description of a boiler for burning a coal of low quality so that steam may be raised at a good rate for colliery power plant. (20)

4. The steel for a mechanical pick is to be of round section, 1 inch diameter, with a round point at one end. The other end is to be made 5/8 inch square for a length of 2½ inches, followed by a round flange 1¾ inches diameter and ½ inch wide. The length overall is to be 7 inches. Make a full-size drawing of the pick steel and indicate (without words) that one end is square. (20)

5. Name the safety devices in use in a plant for raising and lowering men in a deep shaft. Describe one of the devices. (20).

6. Of what materials would you make the following parts? Give reasons for your choice. (a) The portion of the main bearing for an engine crankshaft in contact with the shaft. (b) The handle of an air hammer drill. (c) The thin plate valve of an air compressor. (d) The bridle chains for a cage. (20)

ARITHMETIC AND SURVEYING.

Arithmetic. — 1. Make out a statement of the total wages cost of an output of 2,570 tons 8 cwts., the average rates per ton paid being: (a) Miners (face men), 3s. 9½d. per ton (b) other underground workmen, 2s. 8¾d. per ton; (c) surface workmen 1s. 8½d. per ton. (20)

2. The observed velocity of the air-current in an air-way 10 feet 6 inches by 7 feet 9 inches is 375 feet per minute. What quantity of air is passing per minute? What quantity would pass if the velocity were increased by 7½ per cent. ? (20)

3. A heap of coal, as it came from the pit, lying in stock at a colliery, measures 75.5 feet by 45.25 feet by 11.2 feet. What is the weight of coal if 42 cubic feet weigh one ton? What approximately, would the same cubic content of small coal through a screen with 2½-inch diameter holes weigh? (20)

4. A three-throw pump with rams 12 inches diameter, and a stroke of 18 inches, making 40 revolutions per minute is found by measurement to deliver 800 gallons per minute. What is the percentage loss? (20)

Surveying. — 5. The length of a straight line, measured with a chain which was afterwards found to be 66 feet 3 inches in length, is 1,577 links. What is the correct length in links and in feet ? (20)

6. The following shows the booking of a short traverse :—

Find by plotting the point C on the fourth line at which a drift should be set away at right angles to that line to strike the point A. What is the bearing of the drift AC and the gradient of it? Plot to a scale of an inch to 100 links. (20)

7. Draw a plan, on a scale of an inch to 10 feet, of a longwall face (showing two roads) in a seam 3 feet thick. The roads are 40 feet apart, and 7½ feet wide between the pack walls, or road side buildings. The brushing or ripping is 6½ feet by 4 feet. The rows of props supporting the roof are 3 feet apart, and the props 4 feet apart in line. Make a hand sketch of a cross-section from road to road on a line parallel to the face. (20)

MINES ACTS, ETC.

1. Compulsory Question. — Write in the form of a report to your manager a very short and concise account, with sketches and dimensions, of an accident from a large fall on a haulage road. (20)

2. State the provisions of the Coal Mines Act, 1911, relating to the dimensions of travelling roads and what are the powers of the Inspector of the Division in relation thereto. (20)

3. State concisely the provisions of General Regulation 91 as to the construction of stoppings. To what stoppings do these provisions apply and what are the exceptions? (20)

4. Complete as accurately as you can the following extract from General Regulation 7 : "If any person shall cause or become aware of any obstruction in or interference with the ventilation or of any stagnation or impurity in the air of any part of the mine or of any dangerous defect in any part of the roof or sides or of any other source of danger he shall" (20)

5. What shall a workman do if there is not a sufficient supply of material for supporting the roof and sides available at the place appointed by the Act? (20)

6. Give a concise summary of the General Regulations as to the hours of employment of winding enginemen. (20)


* Questions set at Examinations in November, 1927. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Complete sets of questions available through H.M. Stationery Office, 1s 6d. net. The First Class questions were reproduced in last issue.


Related Articles

Pub.
Date
Article (Newspaper)
28 Jan 1927  Examination Questions, Second Class.* (The Science and Art of Mining)
10 Sep 1927  News and Notes (The Science and Art of Mining)
14 Jan 1928  Examination Questions, First Class or Colliery Managers.* (The Science and Art of Mining)
28 Jan 1928  Examination Questions, Surveyors.* (The Science and Art of Mining)
11 Feb 1928  Examination Results (The Science and Art of Mining)
10 Mar 1928  Notes On Surveyors' Examination* (The Science and Art of Mining)
02 Jun 1928  November (1927) Examinations*, Notes on Candidates' Answers (The Science and Art of Mining)

 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print