|
10th September 1927, Page: 59, Column: 2 Metallurgical CokeA recent Bulletin of the British Cast Iron Research Association contains a short article entitled "Notes on the Manufacture and Use of Metallurgical Coke," by Mr. R. Bulmer (chief chemist to the Consett Iron Company, Limited), who deals briefly with the properties of metallurgical coke, and brings to notice some of the principal factors which tend to operate in the two metallurgical processes of iron smelting and refining where coke is used as fuel. He reviews the subject from two standpoints — i.e., (1) Chemical composition and (2) physical characteristics. Chemical Composition. — The chemical composition of all fuel is of vital importance, and the subject has been emphasised in most places where fuel is bought and sold. All are evidently agreed that if a commodity is sold as a fuel, it should contain as little as possible of inert or non-combustible material. From the point of view of the metallurgist, however, the purity of coke for iron-smelting and refining is of paramount importance, since, apart from its obvious inert properties, non-combustible matter represents a greater and potentially more complex series of losses, and in a recent exhaustive large-scale test on a blast-furnace plant, involving the use of about 12,000 tons of coke, it was demonstrated that an increase of 1 per cent. in the ash content of the coke charged, represented an increase in fuel consumption of 0.4 to 0.5 cwt. per ton of pig-iron produced. Apart from the percentage present and its content of what may be termed "objectionable elements" (e.g., phosphorus and sulphur compounds) the composition of the coke ash is important from the foundryman's point of view. A very large number of cokes have been found to yield an ash of low fusion point, and in some cases the ash actually becomes plastic before the coke in which it occurs begins to burn in the combustion zone of the cupola. Since the fusion point of the coke ash is a result of its chemical constitution, care should be taken to avoid the use of coals whose ashes either individually or collectively tend to fuse easily. For foundry work, cokes having ash fusion points higher than 1,250 deg. C. should be sought. With reference to the sulphur and phosphorus content of metallurgical coke, it is noteworthy that, since both these elements (especially phosphorus) are usually found in the mineral constituents of the ash, they are often lower in low ash cokes than in those whose ash content is high. For foundry purposes a high-sulphur coke is more objectionable than one high in phosphorus, and therefore cupola processes demand coke containing less than 1 per cent. of sulphur. Moreover, under the oxidising conditions of the foundry cupola the possibility of reduction of phosphorus from its oxide is remote. Blast-furnace coke, when used in the manufacture of hematite pig-iron, should be low in phosphorus, since practically the whole of the phosphorus enters the metallic product of the furnace. Specially-selected coals are used for blast-furnace cokes on this account. Sulphur is more easily controlled in the blast furnace, and unless the burden is high in sulphur, the coke may contain more of this element than is permissible in foundry cokes. Excessive sulphur in blast-furnace coke is disadvantageous, however, from the point of view of fuel economy, since its ultimate extraction requires three times its weight of carbon. Physical Characteristics. — It will be seen from the above that, from the point of view of chemical composition, foundry and blast-furnace coke have certain requirements in common. In the light of physical characteristics, however, the two would appear to have only one property in common, namely, "robustness," in the sense of ability to withstand both severe shock and abrasion, as well as high compression stresses. It is well known that coke which is weak in this respect does not give good results in practice. Consideration of the relative requirements as regards coke for the two processes under notice reveals the fact that in almost all respects the one process demands opposite physical properties in the coke from the other. For instance, the foundry cupola gives best results when a strong, fairly large, slow-burning coke is used, whilst the tendency of modern blast-furnace practice is to use a well-screened, rather small-sized, strong, yet rapidly combustible fuel. The requirements of these two processes demand, therefore, two distinctly different cokes, considered from their physical standpoint. Within recent years very great advances have been made in the technology of coal carbonisation, and, as a result, it is now possible from a given coal to produce a variety of cokes suitable for different processes and conditions. The many factors involved in the process of manufacture, however, require the use of various types of coke oven, and also of preparation of the coal before carbonisation.
|
|||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||