|
27th August 1927, Page: 36, Column: 1 Examination QuestionsSecond Class or Under-managers*MINE WORKING. 1. What are the conditions favourable to the pillar and stall system of working? Sketch a small district worked on this system. (60) 2. Describe with sketch the arrangements you would make in a sinking shaft to prevent the hoppit from swinging when travelling in the shaft. (60) 3. Describe with sketches the methods in use to prevent the escape of dust into the air whilst drilling shot-holes in hard sand stone. (60) 4. In order to obtain the maximum output per man per shift from the coal face, to what particular points, other than coal-cutters and conveyers, would you direct your attention? (60) 5. An incline dipping 1 in 4, equipped with direct haulage, is fed from levels driven at right angles to the incline. Show in detail the arrangements you would put in at an intermediate level to expeditiously land the empty train of tubs in the level and pick up the full train. (60) 6. Describe in detail how you would splice a Langs Lay endless rope. (60) THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine which accompanies this paper show how you would ventilate the working faces by means of four separate air-currents (splits) and three air-crossings. Show the direction of each air-current and the positions of air-crossings, doors, stoppings, regulators and sheets, and avoid placing air-crossings in positions in which they would obstruct the haulage. (50) 2. Specify the volumes of air, in cubic feet per minute, required for the combustion of a miner's safety-lamp, the breathing of a man, and the breathing of a horse respectively. Name some of the conditions that prevail in mines which render it desirable to introduce larger volumes of air per man employed than the aggregate of these three. (50) 3. Sketch a Korting ventilator; show its internal construction and describe its mode of action; or alternatively, sketch and describe a Typhoon blower or a small auxiliary fan actuated electrically. (50) 4. Sketch and describe the construction of a Guibal ventilating fan. Explain carefully and fully the object of providing it with an expanding chimney. (50) 5. What is the height of the motive column in two shafts, each 500 yards deep, connected at the bottom by an airway, when the barometer stands at 30½ inches, and the average temperature of the air in one shaft is 52° F., and in the other 75° F. (50) 6. Describe the physical properties, composition, and mode of occurrence in mines of carbon monoxide and carbon dioxide gases. (50) 7. A ventilating fan is drawing 340,000 cubic feet of air per minute through the workings of a mine with a water-gauge of 6 inches. Calculate the horse-power in the air. (50) EXPLOSIONS, ETC. 1. A fire has broken out in an engine room at the bottom of the downcast shaft during working hours. What steps would you take for the safety of the men in the workings, and how would you deal with the fire? Make a sketch plan of the shafts and roads showing the seat of the fire, and the ventilation. (20) 2. What can be done in connection with the ventilation of mine workings in order to minimise the dangers of spontaneous heating in goaves and coal pillars? (20) 3. A brick-work dam has been built in a cross-measure drift to seal off water with a head of 400 feet. It is found that water is finding its way past the dam through breaks or fissures in the strata. What steps would you take to make the dam effective? (20) 4. A workman inadvertently enters an irrespirable atmosphere, the oxygen content of the air having been reduced by an excess of firedamp. He is believed to be alive, but unconscious. As under-manager you are quickly called to the scene ; how would you proceed to rescue him? (20) 5. Spontaneous heating has started unexpectedly in a district of a mine in which no preparation has been made for sealing off. The mine is one in which firedamp is given off freely, and there are only two openings into the district, the intake and the return. It is imperative to seal off quickly; how would you proceed ? A sketch should be given to illustrate your answer. (20) 6. As the leader of a rescue party you are about to enter with your team an irrespirable atmosphere. What equipment would you carry, and what precautions would you take before entering such an atmosphere to ensure the safety of yourself and your party? (20) MACHINERY. 1. Describe the tub draw-bar and coupling best known to you, giving leading dimensions. Mention their good and bad points, if any, and state how they might be improved fur their particular duty. (20) 2. State the differences between direct-current electric power and plant and 3-phase alternating electric power and plant. (20) 3. What are the properties that make a water bad for boiler purposes? How may a bad feed water be improved? (20) 4. Describe a direct-acting compressed air pump suitable for draining dip workings and for handling dirty and gritty water. What are the materials used for making the watertight joints, for packing the plungers and for packing the piston rod? (20) 5. Make in your answer book a full size drawing of a taper key 1½ inch wide, 1 inch thick at the large end and 6 inches long exclusive of the gib head. Show the key by plan and side elevation and state the amount of taper that you would use. (20) 6. Describe two forms of pipe joint suitable for use in underground roads for carrying water or compressed air. The pipes are say 4 inches in diameter. (20) ARITHMETIC AND SURVEYING. 1. Arithmetic. — Two men, in a seven-hour shift, strip a machine. cut face 48 feet long in a seam 33 inches thick with an under-cut of 3 feet. What weight of coal does each man fill, and what wages does each earn if the filling rate be one shilling and ninepence per ton? What depth of cut would be necessary if the shift were increased to eight hours, and the output were increased in proportion ? (20) 2. A three-throw pump with rams eight inches in diameter, and a stroke of eighteen inches, makes forty revolutions per minute. Calculate the delivery of the pump (without making any allowance for slip, etc.) in gallons per minute. The diameter of a pipe squared is approximately equal to the number of pounds of water in a yard of pipe. What is the percentage error in this approximate formula? (20) 3. The contract price for driving a stone drift ten feet wide by seven feet high is four pounds per yard. If the rate of advance per week of seventeen shifts, of three men each per shift, averages thirty feet, what wages are earned by each man per shift, allowing one pound per yard for explosives, and what quantity of material in cubic feet is taken out in each shift? (20) 4. Five men are set to do a piece of work which will occupy them thirty days. After working ten days three additional men are put to the work. How long will it take to do the whole work, assuming the rate of progress is proportional to the number of men employed? (20) 5. Surveying. — You are given the magnetic bearing of a road to be laid off from a stated starting point. On arriving at the place you find it surrounded with material that attracts the needle and which cannot be removed. How would you proceed if you had only a loose needle dial ? What do you consider the best way of marking off the line in a road that has to be driven a long distance accurately to bearing? (20) 6. The co-ordinates of two points A and B are respectively N950, W150; and N400, E125. Lay down these two points, and take off the quadrant bearing from A to B with your protractor. The level of A is 510.5 and of B 360.5 above a given datum. Find by construction the actual length of AB measured on the slope, and check it by calculation. (20) 7. Plot the following short loose needle traverse made with a dial reading clockwise, the north end always leading
What is the bearing from B to A both Azimuth and Quadrant, and the plan length of BA ? If the level of A is 100 what is the level of B? (20) MINES ACT, ETC. 1. Compulsory Question. — Write, in the form of a report to your manager, a description, illustrated by sketches, of a haulage system at a colliery with which you are familiar. Mention the various safety appliances in use in connection with it. (20) 2. To what roads is stone-dusting to be applied? Quote the General Regulations as to the method of stone-dusting and the nature of the dust to be applied. (20) 3. What are the provisions of the Coal Mines Act, 1911, and General Regulations as to storage, use, and care of detonators? What is the effect of the order of 10th November, 1926 ? (20) 4. What references are there in the Coal Mines Act, 1911, to wages of workmen? (20) 5. Describe the provisions of the Order (21st May, 1912) prescribing the manner of searching persons employed below ground. (20) 6. Quote the provisions of the Coal Mines Act, 1911, and General Regulations relating to air measurements underground. (20) * Questions set at Examinations in May, 1927. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Price of official copy of questions obtainable through H.M. Stationery Office, 1s 9d. net. [For 1st Class questions see p. 26, No, 2, Vol. 38.]
|
|||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||