Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Main Document Archive
Newspaper Articles
Articles by date
Articles by colliery
Personal name index
Local Record Extracts
D.M.A. Document Archive
Transactions of I.M.E.
Miners' Welfare
N.C.B. Archive
The Colliery Engineer
The Colliery Guardian
Mine & Quarry Engineering
Mining Journal
The Science and Art of Mining
Coal Magazine
Coal News
Coke and Gas
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious


 Newspaper Articles Index Newspaper Articles 

8th June 1927, Page: 353, Column: 1

Rock Drilling Machines

Before the South African Institution of Engineers Mr. Henry S. Potter submitted a paper on "Drilling Holes in Rock." In his reply to the discussion which is given in the Journal of the Institution, the author repeats as follows four axioms which were given in his original paper. There is one very important point which operates in connection with these axioms, namely, that it is most advantageous to get as high a velocity jet of water at the cutting edge as possible, so as to remove the debris in as large pieces as possible from the space surrounding the reaming edge which is formed on the wing of the bit.

(1) In all drilling operations the diameter of the bit on the longest steel of the set should be ¼ inch larger than the diameter of the steel; in other words, there should be 1/8 inch wing clearance on either side of the steel (this is to give sufficient space for the debris to pass away from the cutting edge up the length of the hole).

(2) The limiting drilling speed of any machine is the breaking strength of the drill steel that will drill the hole required. For instance, assuming that axiom No. 1 is correct, to drill a 7/8 inch hole, the diameter of the steel for this purpose, at the back of the cutting edge, cannot be more than ¾ inch in diameter, so as to give 1/8 inch wing clearance on either side of the steel. The finishing bit in this case would be 1 inch, and as one normally wears off 1/8 inch in the run, the finishing hole would be 7/8 inch, plus a slight increase in diameter owing to the chatter of the steel, and for a 1¼ inch hole a 1 /18 inch round steel should be used. This axiom applies to parallel steel. With regard to taper steel, the breaking strength is equivalent to the largest diameter of same.

(3) The length of the shank should be proportional to the average angle of hole drilled. If drilling holes vertically, a shank 3¼ inches is probably long enough. For holes drilled 45 degrees below or above the horizontal 4¼ inches to 5 inches will probably do, and if the majority of holes are flat or 10 degrees above or below the horizontal, a 6½ inches to 7 inches length of shank would be advisable,

(4) From a rock drill user's point of view, this axiom is the most important, viz., that the area of the shank should be proportional to the air consumption of the machine ; for instance, a ¾ inch square shank, provided the water tube does not have to lie in the axial hole, is large enough for a machine using 35 feet of air per minute, but I do not think a 7/8 inch square shank, with a 3/8 inch axial hole for the water tube to function, is large enough for a machine using 85 feet of air per minute, this being the air consumption of the majority of hand held jackhammers used on the mines. I suggest for this machine that, instead of using a square shank, the ideal shank is one of round section with two or more grooves engaging in ribs provided in the chuck, and the axial hole should be at least 7/10 inch in diameter. This would mean that the ¼ inch water tube would have at least 1/32 inch of space surrounding it so it could not be cut off, and, granting the shank in the jackhammer was 1¼ inches diameter, this would be sufficient for machines using up to 85 feet of air per minute.

The round shank will fit the round hole in the chuck more perfectly than a polygonal shank would, and would so ensure the striking face of the piston, and the face of the shank would be parallel and the blow would be spread over the full area. Of course, for machines using a larger amount of air than 85 feet, the area should be increased as could also the length, for instance, in a hammer drill, having a 6½ lb. piston and using 110 cubic feet of air per minute at 80 lb., the shank should be 1 5/8 inches diameter, and 6½ inches to 7 inches long with four longitudinal ribs to engage the flutes in the chuck. This would be welded on to the collar by means of an electric butt welder.


Names mentioned in this article

 

 Name  Age  Occupation  Notes 
Potter, Henry S.    Mining Engineer  


 

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 28 Nov 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print