|
26th March 1927, Page: 280, Column: 2 Examination QuestionsFirst Class or Colliery Managers.*WINNING AND WORKING. 1. Two seams of coal, 20 yards apart and each 4 feet thick, are to be worked. The strata in the vicinity of the seams are only moderately strong. What methods and conditions of working would you adopt in order that both seams may be worked in an efficient manner? (50) 2. What is meant by high-temperature carbonisation and low-temperature carbonisation of coal respectively? What advantages are claimed for the latter treatment? (40) 3. Describe, with sketches, the arrangements you would make for the suspension and lowering of a pump which is capable of dealing with large quantities of water in a sinking shaft. What kind of suction pipe would you recommend? (40) 4. The brick arching in a tunnel 20 feet wide by 15 feet high is badly crushed at the crown. Show by sketches the temporary supports you would erect and how you would carry out the replacement of the arch. (40) 5. Sketch and describe a self-acting door, so arranged as to open with the tubs when they are going in the opposite direction to that in which the door opens. (40) 6. Under what circumstances would you install a gate-end loader in connection with a coal face conveyor? Illustrate your answer with sketches. (40) 7. What precautions would you take in order to reduce the likelihood of blown-out shots and miss-fired shots respectively? How would you proceed in case of a missfire? (40) THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine which accompanies this paper, show how you would ventilate the working faces by means of seven separate air-currents (splits) and five air-crossings. Show the direction of each air-current and the positions of air-crossings, doors, stoppings, regulators and sheets, and avoid placing air-crossings in positions in which they would obstruct the haulage. (30) 2. The quantity of air discharged from the chimney of a ventilator is 100,000 cubic feet per minute ; its velocity at the point of discharge is 1,000 feet per minute; the water-gauge in the fan drift is 2 inches. Assuming the air to weigh 0.075 lb. per cubic foot, and the efficiency of the ventilator to be 63 per cent., what is the mechanical output of the ventilator expressed in horse-power, and what proportion of this power is absorbed in imparting velocity to the air? (50) 3. Make a sketch of any hygrometer, but preferably of a "whirling" one; describe its mode of action; state how the actual value of its indications can be arrived at; and to what use they can be put in connection with mining operations. (30) 4. Make a sketch of Walker's Indestructible fan, showing how its blades are curved with reference to its motion of rotation, and how they are connected to the central shaft. Augment your sketch further so as to show how the direction of the ventilating current can be reversed when desired. (30) 5. By means of a sketch, show the shape and magnitude of the firedamp cap in integral percentages of firedamp in the air; state, in inches and fractions of an inch, the heights to which the caps attain in the safety-lamp best known to you; describe any means known to you whereby the visibility of the caps may be increased by imparting colour to them or otherwise. (30) 6. A ventilating current of air is travelling through an airway of uniform rectangular cross section, 10 feet wide by 7 feet high, and 3,200 feet long. The difference of pressure between its two ends is equal to that of a column of water 2 inches high; the coefficient of friction is 0.001 ; the temperature of the air is 70 degrees Fahr.; the atmospheric pressure 31 inches. What weight of air is passing unit area (70 square feet) per minute ? (30) 7. In a sinking pit the men who are descending to examine the conditions at and near the bottom, after firing a round of shots, encounter an explosive mixture of firedamp and air at a distance of 50 yards above the bottom. The ground in the pit bottom immediately above a fissured bed of sandstone has been blown up by the pressure of the gas which is now coming off in sufficient quantity to render the ventilating current explosive. How would you propose to deal with the situation : first temporarily, to enable you to continue the sinking; and secondly, permanently, if the blower continued to give off the same quantity of gas for an indefinite period of time ? (30) EXPLOSIONS, ETC. 1. A large feeder of water is flowing along a roadway from disused workings to the pumps at the pit bottom, and a large fall occurs which blocks the roadway and holds hack the water. There is a danger as the water accumulates behind the fall of it suddenly breaking through. What precautions would you take : (a) For the safety of the men working in the mine? (b) To prevent the pumps being submerged at the pit bottom? (30) 2. What are the dangers of coal dust? How can the quantity of dust be reduced : (a) Entering the mine ? (b) In the mine What must be done to ensure safety, and how would you keep a check on the general condition of the underground road ways? (25) 3. Make a diagrammatic sketch of any type of self-contained breathing apparatus you are familiar with and describe the same. (25) 4. Owing to a gob-fire it has been necessary to build off a district in a seam of coal by stoppings in two levels, and after a time it becomes necessary to move the stoppings inbye a distance of 100 yards without interfering with the extinctive atmosphere in the district. How would you proceed with the work? (25) 5. Make a sketch with dimensions of a brickwork dam to resist the pressure of a head of 200 fin. of water. The dam is to be built in a level 9 feet wide by 6 feet high in a coal seam 4 feet 6 inches thick, overlain with 1 foot 6 inches of shale, beneath a rock roof, and resting on 12 inches of fireclay. (25) 6. How may accidental fires be caused in a mine where safety-lamps are used? Draw up a few simple rules for preventing same. (25) MACHINERY. 1. Describe a centrifugal, or turbine, pump to raise 500 gallons per minute, against a total head of 500 feet, suitable for being driven direct by an electric three-phase motor. Of what materials would you make (a) the casing, (b) the shaft or spindle, (c) the impellers, (d) the diffusers or guide vanes. (28) 2. Describe an air hammer drill for boring holes in a sinking shaft. Give its approximate weight and describe the drill steel that is used and the mechanism for rotating the drill steel. Say what pressure you would prefer to have available at the control cock. (28) 3. A mine shaft is circular, 16 feet diameter. The drum of the winding engine is 12 feet diameter and its centre is level with the banking level and 70 feet away from the shaft centre. The headgear pulleys are 12 feet diameter, their centres being 60 feet above banking level. In side elevation, the winding ropes coincide with the shaft centre. Using a scale of 1 inch to 16 feet, make in your answer book a drawing of the above features in side elevation, and sketch in a suitable headgear showing the chief dimensions. Use single lines for the drum and pulleys and for the members of the headgear. Constructional details are not wanted. (38) 4. The diagrams on the separate sheet show items of electrical apparatus and plant for an electric haulage. By drawing lines in ink on the sheet, show how the incoming supply cable, the oil break switch, the reversing switch, the starter, the motor, the voltmeter and the ammeter should be connected by cables or conductors. (28) 5. The drum of a winding engine is bi-cylindro-conical. There are six active coils of rope on the small cylinder, which is 10 feet 10 inches diameter. There are four coils on the scroll or conical portion. The large cylindrical portion is 16 feet 10 inches diameter. How many coils of rope will there be on the large cylinder when the cage is at bank if the total depth of wind is 1,200 feet ? The diameter of the rope is 2 inches. (Ignore the width of the scroll or conical portion of the drum.) (28) 6. A cage and its attachments weigh 5,000 lb. The cage carries four tubs taring each 600 lb. and carrying 1,000lb. of coal. The length of rope from the pithead pulley to the cage at bank is 80 feet and to the cage at bottom is 980 feet. The rope weighs 2 lb./ft. How far up the shaft from the bottom will the loaded cage be when the pull or tension in the two ropes, taken at the headgear pulleys is equal-the cages being assumed to be at rest ? If the two cages were in steady motion, would the weights balance at the same cage positions as when at rest? Give reasons for your answer. (28) SURVEYING, LEVELLING AND DRAWING. 1. With plan. The level AB running due east in seam D has struck a fault at B, 200 feet above datum. The contours shown are in a seam C, which lies 50 feet above seam D. Draw a section, on the scale of the plan, on the line of a proposed cross measure drift BE, rising 1 in 100, and find the point where the drift will win out the seam D east of the fault. What is the throw of the fault? (30) 2. The following fast needle survey was made with a dial, reading anti-clockwise, for the purpose of fixing the starting point of a bore vertically above the drift passing under it
The distances are measured on the slope. Find by plotting the position at which the borehole must be set off, and its approximate depth. Corrections for dip, and the depth of the bore got by construction will be accepted. (30) 3. Calculate the royalty on the coal worked from an area of 12.540 statute acres in a level seam 54½ inches thick if the royalty rate be 50s. per inch thick per acre. If the weight of the coal be 126 tons per acre 1 inch thick, what would be the equivalent royalty rate per ton, allowing 7½ per cent, free for colliery use ? (30) 4. In measuring a line of a surface survey, you find that it crosses a pond. Show by a sketch and explanation how you would find the distance across the pond to a pole on the other side from which you could continue the measurement. (25) 5. Take a length of 5 inches from your scale or foot rule and make a scale of from which any distance up to 500 feet can be taken direct in units of 10 feet. (25) 6. If you found the magnetic meridian of to-day to be 2½ degrees different from that shown on an old mine plan, what date would you take the old meridian to be (approximately) ? Draw the relative positions of the old and new meridian and mark the date of each. (25) GENERAL MANAGEMENT AND MINING LEGISLATION. 1. Compulsory Question. — Describe shortly the steam winding plant at a colliery with which you are acquainted and state the output and depth wound from. Your directors require your advice as to substituting electric power for steam for winding. Write a report setting out the relative advantages and disadvantages which would result. Discuss also the advantages, or otherwise, from the point of view of safety. (30) 2. State the provisions of the Coal Mines Act, 1911, and General Regulations and the records necessary to be kept respecting (a) Winding ropes. (b) Hauling ropes. (c) Cage chains. (25) 3. What instruments indicating the condition of the atmosphere are required by the Coal Mines Act, 1011, to be provided at a mine ? What is the object of each of them? Where are they to be placed? What are the regulations as to recording the readings? (25) 4. Give shortly the various duties of firemen, examiners or deputies assigned to them by the General Regulations. (25) 5. It is provided in General Regulation 119 relating to the use of electricity that notice shall be sent to the inspector of the division on the forms prescribed by the Secretary of State, in three different circumstances. State what they are and what apparatus is not included. (25) 6. Describe shortly the official tests to which a safety-lamp has to be subjected before being approved for the purposes of the Coal Mines Act, 1911. (25) * Questions set at Examination in November. 1926. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. For Surveyors' Questions see No. 15. and for Second Class see No. 16. Complete sets of questions available through H.M. Stationery Office, 1s 3d. net.
|
|||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||