|
26th February 1927, Page: 246, Column: 1 Examination QuestionsSecond Class or Under-managers.*MINE WORKING. 1. Draw a lay-out of what you consider to be a fireman's district in a level seam 4 feet thick with a strong roof and floor. Give the number of men in the district, and mention their separate duties. (60) 2. Show by sketches the setting out of the top and bottom of a self-acting incline for expeditiously dealing with a large output of coal. What arrangements do you consider ought to be installed for the prevention of accidents ? (60) 3. What precautions would you take in order to reduce the likelihood of blown-out shots and miss-fired respectively? How would you proceed in case of a miss-fire? (60) 4. A hand-gotten seam is yielding an excessive percentage of small coal. What can be done by care and method of working to increase the percentage of large coal ? (60) 5. What are the principal causes of tubs becoming derailed in a main haulage plane? Describe, with sketches, a good device for re-railing the tubs while in motion. (60) 6. A water lodge and pump house have to be made in a seam of coal dipping 1 in 4 midway in a winding shaft fitted with rigid guides. Sketch a lay-out for this work, and state the arrangements you would make for the winding from the landing while this work is going on. (60) THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine which accompanies this paper, show how you would ventilate the working faces by means of seven separate air currents (splits) and five air crossings. Show the direction of each air current and the positions of air crossings, doors, stoppings, regulators and sheets, and avoid placing air crossings in positions in which they would obstruct the haulage. (50) 2. What is the chemical composition and specific gravity of air, firedamp and carbon dioxide respectively (hydrogen=1)? (50) 3. Describe the process of diffusion of gases. State the relative rates of diffusion of the four gases mentioned in the previous question. (50) 4. A fan is drawing 30,000 cubic feet of air per minute through a certain airway against a resistance equal to a water gauge of 3 inches. What power would the fan require to develop in order to draw twice the same quantity of air through the same air way? (50) 5. Make a neat sketch and describe the details of a Marsaut safety-lamp on a scale of about one-half its natural size. Show where the air enters and leaves its interior and trace its course inside the lamp by means of arrows. (50) 6. Given two shafts, each 17 feet in diameter by 400 yards deep; a mean barometric pressure in both of 31. inches ; an average temperature of the air in one of 55 degrees Fahr., and in the other of 70 degrees Fahr. What is the height of the motive column corresponding to these data? (50) 7. Show by means of a sketch in plan, side elevation and end elevation, and describe in words what you consider to be the strongest possible air crossing that can be constructed. (50) EXPLOSIONS, ETC. 1. In working a seam of coal on the longwall system, advancing to the rise where firedamp is given off freely, would you consider it advisable to keep the ripping of the roadways near to the face or a few yards behind? Make a sketch to illustrate your answer and give reasons. (20) 2. What arrangements would you make underground for adequately stone dusting the roadways in an extensive mine, and how would you satisfy yourself that the stone dusting was satisfactory ? (20) 3. Make sketches, with dimensions, of the preparatory portions of a stopping ready for sealing off a district in case of heating or fire. The stopping is required in the roadway of a seam 7 feet 6 inches thick, dipping 1 in 3, with 2 feet of shale overlying the coal and 1 foot of soft fireclay beneath it. (20) 4. You are approaching from the dip old workings in a seam dipping one in four, containing water at 300lb. per square inch pressure. This water has to be tapped and drawn off. How would you proceed to deal with it? (20) 5. What precautions would you take in fitting up a self-acting incline in a dry and dusty mine to prevent an outbreak of fire? (20) 6. A change is observed in the smell of the air in the return airway from a district, and es the under-manager your attention is drawn to it. What dangers might it indicate, and what steps would you take? (20) MACHINERY. 1. Describe the construction of the following types of wire rope used for winding or haulage, or both: (a) Lang's lay; (b) ordinary lay ; (c) locked coil ; (d) Any one other special construction known to you. State in each case for what particular conditions the type is most suitable. (20) 2. The crankshaft of a three-throw pump turns at 40 revolutions per minute. The spur wheel on the crankshaft has 72 teeth and meshes with a pinion on the countershaft having 20 teeth. The pump is to be driven by a motor having a belt pulley 12 inches diameter turning at 725 revolutions per minute. Ignoring belt slip, what must be the diameter of the belt pulley on the pump countershaft? Give the answer correct to the nearest half-inch. (20) 3. State the differences between a centrifugal or turbine pump and a three-throw ram pump and name conditions in which each type is to be preferred. What is the effect of operating a stop valve placed in the rising main of each type of pump? 4. The sketch shows a portion of a mild steel drum tread supported by a cast-iron ring or ledge forming part of the drum side. Make in your answer book a full-size drawing showing one of the bolts that you would use for securing the tread to the drum side. State how you would secure the bolt in position and the means taken to prevent the bolt from getting slack. Show all important dimensions. (20) 5. Give a description of a direct-current dynamo having an output of, say, 20 kw. and arranged to be driven by belt. (20) 6. Give a list of the statutory and other necessary mountings attached to a Lancashire boiler. Describe the construction and mode of working of the junction (or crown) valve for steam. What would be about the size of this valve on a boiler 30 feet long, 8 feet diameter, for 120lb. per square inch working pressure ? (20) ARITHMETIC AND SURVEYING. Arithmetic. — 1. The area of a coal seam worked, as determined by survey and measurement, is found to be 10.535 acres. The average thickness of the seam is 51.5 inches. If the royalty be at the rate of £40 per foot thick per acre, what is the amount of royalty payable? What is the equivalent royalty rate per ton if the specific gravity be 1.280 ? (20) 2. An endless haulage rope, with tubs attached singly at intervals, travelling at a speed of 2½ miles per hour, delivers 420 tons in 6½ hours running time. If each tub holds 12 cwt. of mineral, what is the distance between tubs centre to centre ? If an increase of 15 per cent, in output were required, what would be the distance between tubs? (20) 3. A lodgment with a capacity of 50,000 cubic feet has a feeder of 325 gallons of water per minute running into it. When the lodgment is full a pump lifting 450 gallons per minute starts to pump out of it. How long will the pump take to empty the lodgment? What proportion of the lodgment is empty at the end of 2½ hours pumping? (20)
4. Simplify Surveying. — 5. Plot the following short survey or traverse from A to B. Find the heaving and distance from A to B. Join AB and calculate the area of the closed figure
Plot to a scale of 1 inch to 100 feet. (20) 6. A roadway driven to the full rise has a gradient of 1 in 5½ Find by construction the gradient of a road making an angle of 40 degrees with the other. (20) 7. A road dipping at 1 in 6 for 300 feet from A strikes the bottom of a basin or syncline, runs 50 feet level, and then begins to rise at 1 in 3 for a length of 210 feet to B. What is the difference of level between A and B, and what would be the inclination of a drift joining these points ? Note the lengths given are plan measurements. (20) MINES ACT., ETC. 1. Compulsory Question. — Write in the form of a report to your manager a detailed description, illustrated by sketches, of the pit-bottom and shaft siding arrangements at the pit-bottom at a colliery with which you are acquainted. Criticise the plan from the point of view of safety and suggest improvements. (20) 2. What means have to be taken to make known to those employed in and about a mine the provisions of the Coal Mines Act and General Regulations? (20) 3. What appliances, to safeguard against accidents, are required to be provided in connection with winding shafts where men are raised and lowered? (20) 4. There are certain occurrences in and about a mine which it is necessary to report to the Government Inspector, even if they do not cause injury to persons. Enumerate them. (20) 5. Give a summary of the General Regulations relating to ambulance and first-aid appliances. (20) 6. Quote as accurately as you can the definition given in the General Regulations relating to electricity of the following expressions : (1) "High pressure." (2) "Apparatus." (3) "Open sparking." (4) "Switchgear." (5) "Authorised Person." (6) "Electrician." (20) * Questions set at Examination in November, 1926. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced. Complete sets of questions available through H.M. Stationery Office, 1s 3d. net.
|
|||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||