9th October 1926, Page: 88, Column: 2
Mechanically Loaded Coal
The preparation of mechanically loaded coal in mines where seams contain
considerable impurities is a subject that requires careful consideration before
machines are installed, unless provision is made at the tipple for its
preparation. Conditions vary a great deal in the different seams, so much so
that a mechanical loader may be unsuccessful in one seam and yet the same
machine may make good in another where conditions are different. The effect of
impurities in the coal seam on mechanical loading will also vary according to
the thickness of the seam. In thin seams impurities will be more difficult to
remove than from thick seams, states Mr. E. H. Graff in a paper before
the A.I.M.E. discussing the New River Co.'s experiments. Coal from any loading
machine must be loaded into the mine cars in such a manner that the lost time
in placing cars be cut down to a minimum, and therefore conveyors should be
used in conjunction with the loading machine. The Jeffrey Manufacturing Co.
built a conveyor known as the 44-B conveyor loader. These conveyors are only
about 16 in. high at the back, the flights sliding on a thin plate laying on
the bottom of the seam. Mr. Graff says the ordinary amount of impurities
in the Sewell seam can be picked from this conveyor and thrown back into the
gob or waste, and they feel that coal can be loaded as clean under these
conditions as it can be done when loading this coal by hand ; in fact, cleaner
in some cases. This 44-B conveyor loader is a long face or pillar machine, and
in addition to loading the coal from the pillars mechanically, they felt that
it was necessary to drive narrow work quickly in order to get development when
needed. As they had coal 4 ft. and less in thickness, and there was no machine
on the market that could be worked in this thickness of coal, they got the
Jeffrey Manufacturing Co. interested in changing one of their large machines so
that it would work in coal 4 ft. in thickness. It is known as the 43-A Short
waloader, and is a machine for development work. It both undercuts and loads
the coal, which is delivered to a conveyor and carried to a trip of mine cars
along the entry. The Shortwaloader, or any other loader, for development work
breaks the coal up more than by hand loading, but Mr. Graff is sure that
the machine is blamed for more of this breakage than it is entitled to, as he
does not think proper care is taken in placing and charging the shotholes. It
is much easier for the machine to handle the coal after it has been shot heavy
than if it was not shot so hard ; possibly not so much easier for the machine,
but easier for the workmen who operate it. This is also the general practice
where hand loading is employed, and they find the percentage of fine coal
greater from narrow work than from wide work ; but the author feels confident
that the percentage of fine coal in hand loading within a radius of 2 or 3 ft.
from a shothole is the same in wide work (rooms 18 to 25 ft. wide) as narrow
work. Removal of impurities from the seam where mechanical loading is being
done is the most serious and most difficult problem they meet. In thin seams
without partings, and having but 2 or 3 in. of impurities next to the roof,
there should be no difficulty in removing these impurities at the working face.
In thin seams with parting in coal, if such parting does not exceed 2 or 3 in.,
there should be very little difficulty in removing it, and the removal of the
parting should not interfere much with the operation of the machine. However,
if this parting is of a greater thickness than mentioned, considerable
difficulty would be encountered, especially with development machines, as so
much room is taken up with the machine that there is no room to throw the
impurities until the coal is loaded out. In such cases, it may be necessary to
let the machine handle the impurities and drop them along the side of the
conveyor at the rear of the machine, later to be shovelled on to the conveyor
by hand.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Graff, E. H. | | | |