|
27th March 1926, Page: 285, Column: 1 Examination QuestionsSecond Class or Under-managers.*MINE WORKING. 1. A coal seam 4 ft. 6 in. in thickness and dipping 1 in 4 is to be opened out on the longwall system with the roads of the working faces on the full inclination of the seam. Make a neat sketch of one district showing as much detail as you can, with any explanations you may think desirable. (60) 2. How would you test the roof of a working face to ascertain its safety, and for what reasons are the usual tests sometimes misleading? From your experience what errors are occasionally made in the timbering of a working face? (60) 3. You are in charge of the driving of a cross-measure drift. What precautions would you take to prevent accidents in connection with blasting operations? (60) 4. Given a scam with extensive workings, what provision would you make for the greasing of the tubs having wheels fast on the axles? Would you make any provision for greasing underground? If so, where would you grease and what precautions would you take to prevent the accumulation of grease on the roads? (60) 5. A heavy fall 6 yd. long has occurred in a main haulage road 12 ft. by 6 ft. How would you proceed to clean up the fall so that the road may be used again with the least possible loss of time, the roof above the fall being still unsettled ? (60) 6. Discuss the different systems of underground haulage and state the conditions which, in your opinion, are most suitable for each system. (60) THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine which accompanies this paper, show how you would ventilate the working faces by means of four separate air-currents (splits) and two air-crossings. Show the direction of each air-current, and the positions of air-crossings, doors, stoppings, regulators and sheets, and avoid placing air-crossings in positions in which they would obstruct the haulage. (50) 2. How many cubic feet of air and gas per minute would ascend the upcast shaft (in addition to the air that descends the downcast in the same time) from the workings of a mine, in which the unventilated spaces have an aggregate volume of 3,000,000 cu. ft., if the barometer fell from 31 in. to 30 in. in eight hours. (50) 3. The velocity of the air in a certain air-way is maintained at 350 ft. per min. with a water-gauge of 2 in. What will be the water-gauge if the velocity he increased to 450 ft. per min. ? (50) 4. Make sketches of, and describe, an anemometer. Describe also how it is calibrated. (50) 5. What effect, if any, has a change of temperature at the surface on the ventilation of a mine? Consider, for instance, a rise of temperature from 30 deg. to 60 deg. Fahr. (50) 6. Describe Haldane's method of estimating the quantity of carbon dioxide in the air of a mine. Make a sketch to illustrate the appliance, and describe the principle upon which it is based. (50) 7. If a fan driven by a motor developing 100 h.p. has an efficiency of 70 per cent., what quantity of air in cubic feet per minute will it produce in a mine with a water-gauge of 2 in. ? (50) EXPLOSIONS, ETC. 1. Describe the recognised modern methods of minimising the dangers of coal dust, and give your views on the practical application of each. Which method would you choose as the best, taking into consideration the difficulties or disadvantages, end the ultimate efficiency of the method? (20) 2. What are the principal dangers to be guarded against by an underground exploring party immediately after a colliery explosion, and to what matters should such a party direct their attention during the first day? (20) 3. Make a sketch of a longwall or of a pillar and stall district of workings, and mark the locality of a serious gob-fire which requires to he dealt with immediately. Describe how the fire has been caused, its condition when you commence operations, and how you would deal with it. (20) 4. Four rescue teams are available for carrying out certain building work 200 yd. inbye of fresh air. The material has to be carried in, and the work will occupy 16 hours. Set out a detailed programme of work and time for each team. (20) 5. Describe the various circumstances or conditions in coal mining that may injuriously affect the health of the workmen, and the improvements or remedies that may be adopted. (20) 6. What have been the principal causes of flooding involving loss of life in mines ? Give instances, and state how such occurrences might have been avoided. (20) MACHINERY. 1. Describe what is meant by :— (a) Main and tail haulage. (b) Endless rope haulage. Make a simple drawing of the engine (or motor) and gear of each type. (20) 2. Give a description of a water-tube boiler of the Babcock and Wilcox type. (20) 3. Describe shortly the essential parts of the electrical plant needed for an electric three-phase main and tail haulage gear (say, of 150 h.p.), starting from the cable that supplies the current. (20) 4. State the materials used for the following purposes :— (a) The packing for rams of pumps. (b) The packing for piston rods of steam engines using saturated steam. (c) The packing for piston rods of steam engines using superheated steam. (d) Joint rings for steam pipes. (e) Joint rings for water pipes. (20) 5. A pipe is needed with a recessed flange machined to couple to a flange that is 11 in. in diameter, having eight holes for ¾ in. bolts on a 9¼ in. diameter pitch circle and a spigot 8 in. diameter. over-all and 6 in. diameter inside, the spigot projecting ¼ in. above the general surface of the flange. The pipe bore is 6 in. Make in your answer book to a scale of one-half full size (or freehand, not to scale, if you prefer) a plan of the recessed flange to suit the flange with spigot. Show all necessary dimensions indicating the depth of the recess. (20) 6. Describe the Stephenson link motion used on a steam engine for working the valve (or valves) that distributes steam to each end of the cylinder and for reversing the engine. (20) ARITHMETIC AND SURVEYING. Arithmetic. — 1. The contract price for driving a stone drift 10 ft. by 7 ft. is £6 5s. per yd. What is the cost per cu. yd. excavated? How many tubs of 10 cu. ft. capacity will be required to carry away the debris from one shift of workmen advancing the face 2 ft. in the shift ? (20) 2. What weight of water is contained by a vertical column of pipes 18 in. in diameter and 100 yd. long? (20) 3. A coal-cutter cuts 110 yd. of face in a seam 40 in. in thickness to a depth of 3½ ft. What quantity of coal is produced per cut? (20) 4. What is the total cost of 560 tons 16 cwts. at 3s. 6¼d. per ton plus 15 per cent.? (20) Surveying. — 5. Draw an equilateral triangle ABC, of 450 ft. side, on your answer book, to a scale of 1 in. to 100 ft. If the levels of a seam at A, B and C respectively be 150, 240 and 180, show the direction and rate of full dip on your sketch. (20) 6. A drift running level course strikes a fault throwing up the seam 45 ft. The direction of the fault makes an angle of 45 deg. with the drift and the bade is 30 deg. to the vertical. Draw a section on the line of the drift — scale 1 in. equal to 100 ft. — and find the length of a drift rising at 1 in 4½ to recover the seam. The drift is to start 50 ft. back from the fault. Dip of strata 1 in 6. (20) 7. Two seams, 75 ft. vertically apart from floor to floor, dip at 1 in 12. It is proposed to win the upper seam by a stone drift, from the lower seam rising 1 in 4½ in the direction of the dip of the strata. Calculate the length of the drift. Check your answer by drawing a section on a suitable scale. (20) 8. Calculate the plan measurement of a road which measures 1,050 ft. on the slope at a gradient of 1 in 3½. (20) MINES ACT, ETC. 1. Compulsory Question. — Write, in the form of a report such as you would, as under-manager, send to your manager in his absence, a full description of an accident due to overwinding. Explain how it occurred, what steps were taken to repair the damage done and to ensure the safety of the men underground, and make any suggestions as to the prevention of such an accident in future. (20) 2. Give an outline of the General Regulations relating to the use of electricity for working coal-cutters. (20) 3. What are the duties, under the Coal Mines Act and General Regulations, of coal getters at the face ? (20) 4. Give fully the rules which apply to the storage and use of detonators. What danger is there in handling them? (20) 5. Assume you are a fireman or deputy in charge of a district and that you are informed of the presence of inflammable gas in a working place in the district. Describe, in detail, what steps you would take. (20) 6. You are sent by the manager to make an inspection of a main and tail haulage road and to report if it is in compliance with the Coal Mines Act and General Regulations, and safe for men to be conveyed over it. What are the particulars you would note ? (20) * Questions set at Examination in November, 1925. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced.
|
|||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||