|
13th March 1926, Page: 260, Column: 2 Examination QuestionsFirst Class or Colliery Managers.*WINNING AND WORKING. 1. A seam of coal is 4 ft. in thickness and dipping 1 in 6. The roof of the seam is composed of soft shales which, when broken, freely emit firedamp. Sketch a lay-out plan suitable for the working of this seam, and state the precautions you would take to minimise the breaking of the upper strata. (50) 2. How do you account for the various earth movements which are continually taking place? Describe in particular the movements which take place in coal mining districts. (40) 3. At a colliery where the full tubs arrive at the shaft bottom from one direction only, to be loaded into cages with three decks, it is decided to speed up the coal winding by installing simultaneous decking arrangements. Describe with sketches how you would do this with a minimum amount of excavation. (40) 4. In sinking a shaft through water-bearing strata how would you determine the position for placing the wedging curb on which to build cast-iron tubbing? Describe fully the fixing of the curb. (40) 5. A heavy fall 6 yd. long has occurred in a main haulage road 12 ft. by 6 ft. How would you proceed to clean up the fall so that the road may be used again with the least possible loss of time, the roof above the fall being still unsettled ? (40) 6. State the reasons for and against the more general adoption of coal-cutting machinery and conveyors in the mines in this country. (40) 7. Why is it desirable to season timber before sending it down the mine ? Under what circumstances would you use preservatives for timber? What kind of timber do you prefer for bars and chocks respectively? Show by sketch how you would stack props on the surface. (40) THEORY AND PRACTICE OF VENTILATION. 1. On the plan of a mine which accompanies this paper, show how you would ventilate the working faces by means of four separate air-currents (splits) and two air-crossings. Show the direction of each air-current, and the positions of air-crossings, doors, stoppings, regulators and sheets, and avoid placing air-crossings in positions in which they would obstruct the haulage. (30) 2. State what you know about the relative values of the vena contracta in round, square and rectangular orifices. Assuming 0.65 to be the value of the vena contracta for a round orifice, what would be the diameter of such an orifice through which 100,000 cu. ft. per min. of air at normal pressure and temperature, would pass with a difference of pressure equal to that of 4 in. of water on its opposite sides? (30)
3. In Atkinson's formulae 4. Make a sketch of the Waddle ventilating fan, showing its internal construction and how it can best be connected to an engine or motor. Give particulars as to its diameter; its width at the periphery; and the method of connecting it to the fan drift; and state what you know about its mechanical efficiency. (30) 5. Make a careful and correct sketch of the original Davy lamp. Describe its principal defects; show, in consecutive, and as nearly as you can, also in historical order, by what modifications each of these defects has been overcome : state which miners' flame safety-lamp you consider to be the best at the present day, and give reasons for your opinion. (30) 6. Calculate the weight in lb. of 1,000 cu. ft. of a mixture of air and firedamp containing 10 per cent, of the latter at normal pressure and temperature. (30) 7. Describe the various appliances known to you for detecting the presence of firedamp and carbon dioxide in the air of mines. (30) EXPLOSIONS, ETC. 1. Write on one page of your answer book as fully as possible an account of the present state of knowledge with regard to the dangers of coal dust, and remedies therefore. (30) 2. Assume that after an explosion you have made an investigation which has enabled you to trace the path of the explosion, the point of origin, and the cause. Assume your own conditions and write an account of the investigation in sufficient detail to embrace all the important matters observed. (25) 3. In an extensive district of pillar and stall workings a gob-fire has been sealed up for some time by stoppings in the main intake and return roads. It is believed that the fire is extinguished, and it is proposed to resume working. How would you decide that it is safe to do so? How would you restore and re-ventilate the district, and where and when would you commence the working of coal? Accompany your answer by a sketch. (25) 4. How may carbon monoxide be formed in coal mines? What are the characteristics of this gas ? How is it detected, and what precautions are necessary when its presence is suspected ? (25) 5. A trained rescue team visits your colliery for the purpose of an underground practice. Set out a detailed programme of the work which should be included in such a practice. (25) 6. A longwall face is approaching old flooded workings which are under water pressure of 300 lb. per sq. in., and are correctly recorded on your plans. A barrier of coal is to be left to secure immunity from danger. Choose a seam that you know. Describe it and all matters that would require consideration when deter mining the width of barrier necessary. What barrier would you leave? (25) MACHINERY. 1. Describe one of the three types of valve mentioned below, and make a sectional sketch to explain the construction and working of the valve :— A pressure-reducing valve for steam. A Hopkinson-Ferranti steam valve. A retaining or non-return valve, for the rising main of a pump. (28) 2. Describe a Green's economiser, stating how it is installed and worked, and the results that are expected from the use of an economiser. (28) 3. The drawings on the separate sheet show a crosshead with which a piston rod 3¾ in. diameter is to be used. Make in your answer book to a scale of one-half full size a drawing of the end of the piston rod suitably turned down to fit the crosshead and slotted. (Show a total length of roughly 1 ft. of the rod.) Place the slot so that when a cotter is driven through the crosshead nnd piston rod the latter is tightened in position. Show all useful dimensions. (28) 4. Describe an apparatus for application to a winding engine for preventing over-speed at any part of the wind and for preventing an overwind. State the strong and weak features of the apparatus that you describe. (38) 5. What is meant by "power factor" in electrical alternating current power work? What are the advantages of a high power factor ? How may the power factor of an electric system be raised? (28) 6. Define the term "circular pitch" as applied to gear wheels. A shaft turning at 157 revs, per min. has on it a pinion with 21 teeth, the circular pitch being 2.75 in., and it is required to drive a second shaft through gearing at 36.63 revs, per min. How many teeth will there be in the spur wheel on the driven shaft and what will be the distance between centres of the two shafts ? (28) SURVEYING, LEVELLING AND DRAWING. 1. From the information on plan No. 1, draw a section on the line ABC. What seams will be cut by a level stone-drift from the point B towards C, and at what distance from B will the first seam intersected be cut ? Assume the direction of the strike to be the same on both sides of the fault. Draw the section to the scale of the plan. (30) 2. At a colliery there are two seams, 70 ft. vertically apart from floor to floor, dipping due south at 1 in 4. A winning place bearing S.85°E. in the upper seam strikes a downthrow fault of 25 ft. bearing N. and S. At a point A, 30 ft. west from the fault, a drift dipping 1 in 6 is set off to cross the fault on the bearing S.85°E., and recovers the seam at B. From B it is continued in the seam 50 ft. beyond B, where a room is driven in the seam due south a distance of 60 ft. to D. The co-ordinates of C in the lower seam relatively to A are 80 south and 10 east. Find, by plotting. the length of a drift joining C and D and the gradient and bearing thereof. (30) 3. A seam of coal of the section given below is to be worked longwall with roads such a distance apart that the debris from the working completely fills the goaf, or waste, between the roads. The roads are to be 8 ft. wide between the packs, or buildings, and the brushing or ripping, 3 ft. thick and 6½ ft. wide. Give the distance between roads centre to centre.
4. Three bores have been put down to a coal seam at A, B and C respectively. Bore B is situated 500 yd. due north of C and 450 yd. south 60 dog, west from A. The depths are at A 123 yd., at B 165 yd., and at C 145 yd. Find the direction and rate of dip of the seam if the bores start from the same surface level. Calculate the quantity of coal in the triangle formed by the three bores, if the seam be 4½ ft. thick. (30) 5. Plan No. 2 shows an irregular boundary line. Transfer the plan to your answer book and draw from A to a point on BC a straight boundary that will give the owner on each side as much land as he gives up. (25) 6. Calculate the deductions necessary from measurements on the slope to give the true plan measurement for dips of 1 in 2½, 1 in 1 and 30 deg. from the horizontal. State your answer in links per chain. (25) GENERAL MANAGEMENT AND MINING LEGISLATION. 1. Compulsory Question. — As manager of a colliery, you are required to report to your directors as to the advantages and disadvantages of adopting a process of washing, or dry cleaning, of coal from a dirty seam. Write such a report, with a description, illustrated by sketches, of a system you would recommend. State the reduction in ash which you would expect to obtain. (30) 2. What inspections are required by Section 60 of the Coal Mines Act, 1911, of the appliances in actual use for the purpose of raising or lowering persons in the mine? How often are the shafts required to be examined? (25) 3. Give shortly Rules 129 and 130 of the Regulations relating to electricity, on the subject of the protection and support of cables. (25) 4. What are the various plans required to be kept at a colliery office? To what scales are they to be drawn, and what particulars have to be shown upon them? (25) 5. Describe a satisfactory system of registering the men who are underground so that if a person is missing at the end of a shift his absence will be immediately known. Criticise any defect in the system. (25) 6. Describe briefly the provisions of the Coal Mines Minimum Wage Act, 1912. What, in your opinion, has been the general effect of this Act? (25) * Questions set at Examination in November, 1925. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced.
|
|||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||