|
27th February 1926, Page: 250, Column: 1 Examination QuestionsSurveyors.*Transfer plan No. 1 to your answer book. From the information on the plan draw a section on line ABC. Mark on the plan the point where a level stone drift from B towards C would cut the first seam it would intersect on the north-east side of the fault. State the rate of dip on the north-east side of the fault, the strike being the same on both sides of the fault. (12) Make a neat hand sketch of a dumpy level showing the telescope in section. Name the different pacts of the instrument by a tabular reference. Explain why objects are inverted on looking through the telescope. (10) A flanged east-iron pipe of the following dimensions lies on a horizontal plane with its axis at 45 deg. to the vertical plane. Draw a plan and elevation on a scale of 1/12. Ignore bolt holes in the flanges. Dimensions — length, 6 ft. internal diameter, 18 in. external diameter, 21 in. ; diameter of flange, 24 in. ; thickness, 2 in. (10) Plan No. 2 shows an irregular boundary. Transfer the plan to your answer book. Find an equalising line to give a straight boundary from A to a point on BC. Having laid down the new boundary on the ground it is necessary to check the work there by measurement of the exchanged areas. Write out the field notes of the measurement and calculate the exchanged areas directly from these notes. (8) A seam of coal consisting of two bands of coal 15 in. and 12 in, thick separated by 9 in. of fireclay with a holing or undercut of fireclay 5 in. thick is to be worked longwall under the stipulation that the gob or waste, between the roads or gates, is to be completely filled. The roads are 8 ft. wide between the pack walls, or buildings, and the brushing, or ripping, 6½ ft. wide and 3 ft. thick. Calculate the distance between the roads from centre to centre. (8) Two nearly parallel headings driven in a coal seam have met with a large fault at points A and D respectively. The survey notes from A to D are as follows, viz. :—
The levels, in feet above datum, of the several points are : A, 901 ; B, 897; C, 876; and D, 881. Calculate the bearing of the fault, and its position at the surface, assuming the surface to be level and 1,221 above datum, and to be without drift deposit, and that the fault is an upthrow to north-west and has a bade of 30 deg. to the vertical. Make a plan and lay down thereon the position and line of the fault on the surface. Use a scale of (12) Compulsory Question. — You are required to make an underground survey with a theodolite, only one tripod being available. Oil safety-lamps are in use. What arrangements would you make for exhibiting the advance lights and for marking their positions so as to facilitate the placing of your instrument with accuracy? If the workings were highly inclined what test of the theodolite would you consider of special importance, and how would you make it? (12) Calculate the excavation in forming a pond, in level ground, 190 ft. by 140 ft., and 20 ft. deep before lining. The batter of the sides is one in one. Calculate also the quantity of concrete in the lining 18 in. in thickness, and the capacity of the pond in gallons if the top water level be 1 ft. below the level of the surface of the ground. (8) A geologist working in rough country requires to fix, with approximate accuracy, a point in an outcrop on his map which shows few surface features, but contains three fixed points visible from the outcrop. His only instrument is a box sextant. How can the point be fixed in relation to the three points marked on his map? (8) A developing heading on the strike of the seam bearing S. 75 deg. 22 min. E. meets a downthrow fault of 25 ft. The bearing of the fault is N. 7 deg. W. and S. 7 deg. E., and its bade is 17 deg. from vertical. A stone drift dipping 1 in 6 in continuation of the developing heading, starting at A, 30 ft. west of the fault, has recovered the seam at B and a drift has been driven S. 2 deg. 35 min. W. from B, a distance of 50 ft. to C. It is proposed to drive a stone drift from D in a seam 75 ft. lower down to connect with C. The position of D relatively to A is S. 80 ft. W. 25 ft. The dip of the strata is 1 in 37. Calculate the bearing of DC and the actual length of the drift joining D and C. (12) Three bores, A, B, and C, have been put down to a coal seam. B is due north from A 1,200 ft., and C is N. 05 deg. W. 750 ft. from A. The surface levels of the bores are the same. The depth of A is 122 1/3 fm., of B 175 fm., and of C 150 fm. Calculate the direction and rate of full dip, and the quantity of coal in the triangle formed by the bores in a seam 64 in. thick. (8) A piece of ground, several acres in extent, and of irregular contour, is to be excavated to a uniform level. State in detail, but as concisely as possible, the preparations you would make in order to be in a position to measure the work done for determining the payments due to the contractor from time to time. (8) * Questions set at Examination in November, 1925. The figures in brackets against each question indicate the maximum number of marks obtainable. The plans and sketches have not been reproduced.
|
|||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||