|
5th December 1925, Page: 155, Column: 1 Colliery Equipment and OutputIn his paper on "Modernisation of Old Collieries" before the Students' section of the North of England Institute of Mining and Mechanical Engineers, to which reference was made in the last issue of The Science and Art of Mining, Mr. H. P. Mould indicated that within his limited experience he has seen hand-hewing in a thin seam which would have been done more cheaply and more satisfactorily by machines. As an example of how the output per man can be increased by mechanical mining, he quoted particulars from a Northumbrian colliery where the coal is 2 feet 10 inches in height — all clean coal and on the whole pretty hard. In the hand-hewing districts the hewers average from 3 to 3.2 tons per shift. In the coal-cutting districts an output of 6 tons per man is obtained. Thus in this particular case the output is practically doubled by the use of coal-cutting machines. For hand-hewing in bord-and-pillar working, the men are paid at the rate of 2s. 1d. per ton, and on the longwall faces 1s. 7d. per ton. For the same height of coal on the filling faces, the tonnage rate is 1s. 1d. All of these prices are basic prices. Thus Mr. Mould says, in addition to doubling the output, the cost is reduced from 1s. to 6d. per ton, which means with the present percentage of 100, there is a difference in cost of 2s. to 1s. per ton on the hewing. With the increased output, there is a corresponding reduction in other costs, such as haulage. It seems to him that by a larger use of mechanical coal-cutting in the pits the problem of increased output will become less difficult to solve. After making this statement he gives a word of warning to the effect that there are cases where mechanical coal-cutting is not a profitable venture. Regarding the question of mechanical face haulage in the form of conveyors, in regular seams, not much disturbed by faults, and in which the irregularities have to a certain extent become known through the previous working of overlying or underlying seams, Mr. Mould says a great deal can be said for the application of conveyor systems. The charges for stonework, apart from the main winning places, are eliminated, as also the cost of putting and driving. Furthermore, mechanical haulage can be taken right to the coal face, an arrangement which is cheaper and more satisfactory than any other system of haulage. The use of conveyors is advisable on most coal-cutting faces, but, of course, there are many cases where the natural conditions forbid such an arrangement. It does not always follow that the installation of a conveyor results in more economical working. Mechanical coal-cutting and conveying are the chief methods of enlarging the output per man at the coal face, but having obtained that increased output It is necessary to get the most efficient haulage system to transfer it from face to shaft. Modern haulage tends to eliminate horse labour from mines. To Mr. Mould the most desirable system of haulage is endless rope on the main haulage roads and small main and tail systems on the secondary haulage roads. One form of secondary haulage which is worthy of a little consideration is the electric locomotive. The great drawback to the use of them in English mines is the fact that in coal mines only storage battery locomotives are allowed to be used, haulage by locomotives on the overhead trolley wire system being prohibited by the Coal Mines Act. By using storage batteries, the power is strictly limited, and consequently these locomotives can only be successfully used on roads where there is practically no gradient. Mr. Mould has seen a locomotive of this type in use underground, and it was functioning exceedingly well, though there is considerable time spent each day recharging the batteries. Mr. Mould also considered some of the surface arrangements after having dwelt upon simultaneous decking which In a case cited would have increased the output from 120 to 160 tons per hour. The question of power is largely one of concentration and distribution. With a colliery having, say, four pits lying adjacent to each other, it follows, he said, that it is more economical to erect a power-producing plant at some central place and to convey power to each of the four pits from this, than to have four separate power-producing plants at the four collieries concerned. In the opinion of Mr. Mould, in the future central electrical generating stations will be a feature of colliery practice, embracing groups of collieries in one company, or even a whole locality consisting of different companies. After discussing the question of by-product work reference was made by the Author to the manufacture of patent fuel in the form of briquettes. Very little progress has been made in this country, South Wales being the only district where any tangible headway has been made. The north-east coast, so far as concerns the small coals of the Northumberland coalfield, has been content to export this coal to the Continent, there to be briquetted. "If it pays a Continental firm to buy our small coals," said Mr. Mould, "and make them into briquettes, I see no reason why we should not make them at home with equal success." He concludes that "British made briquette plant has proved its superiority both at home and abroad, and with a little vim and earnest endeavour the British made briquette could soon find a good market at home and also speedily win its way to the top in the markets abroad."
|
|||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||