|
Whitehaven AdvertiserArticle from the Whitehaven Advertiser, 23rd June 1894 North Of England Institute Of Mining And Mechanical EngineersGeneral Meeting at Whitehaven and Visits to the Pits, &c.On Thursday last, a general meeting of the members of the North of England Institute of Mining and Mechanical Engineers was held at the Grand Hotel, Whitehaven. Mr. A. L. Steavenson, President of the Institute, occupied the chair, and amongst the members present were :— Mr. H. M. James, Mr. J. D. Kendall, Mr. R. W. Moore, Mr. J. Newton, Mr. E. Gregory, Mr. W. Redshaw, Whitehaven; Mr. G. J. Snelus, Eskett; Mr. G. Scoular, St. Bees; Mr. T. K. Houlgate, Whitehaven; Mr. J. H. Woolcock, St. Bees; Mr. R. P. W. Oswald, Mr. Peile, Hensingham; Mr. B. Cowie, Whitehaven; Mr. R. Russell, Mr. J. Vivian, St. Bees; Mr. W. Fletcher, Mr. W. Watkyn Thomas, Workington; Mr. Robert Hewgill, Durham ; Mr. Jeremiah Head, Middlesborough; Mr. Thos. Varty, Mr. J. S. Corbett, Mr. J. L. Hedley, Newcastle-on-Tyne; Mr. J. W. Marley, Mr. J. M. Marr, Mr. S. Warham, and Mr. Walton Brown, Newcastle-on-Tyne, secretary. After the adoption of the minutes of the last general meeting, a proposed alteration of a bye-law of the institute in order to allow members, associates, and students to compound for life membership by a single payment according to a proportionate scale, was agreed to. A large number of gentlemen belonging to various places not only in this country but abroad having been previously nominated, were elected as members and students, the only local gentlemen nominated being Mr. R. P. W. Oswald, Mr. Robert Kay, and Mr. George Hooper, Whitehaven. The SECRETARY stated that owing to ill-health Mr. David Burns had been unable to complete his "Notes on the Correlation of the Beds of the Carboniferous Series in the North East and North West of England." The PRESIDENT read a paper by Mr. R. Russell, St. Bees, on "The Extension of the Cumberland Coalfield under the St. Bees sand stone, northwards from Maryport and southwards from Whitehaven." In the paper, reviewing the whole evidence which at present exists, Mr. Russell said that the probability is that the Cumberland coalfield of the future will extend from Whitehaven southwards to Drigg, with a breadth inland south of St. Bees of from one mile to one and a half miles and seawards to an unknown distance, probably some miles. In reference to the probable northern extension of the coalfield between Maryport and Waverton on the south and Skinburness on the north, it would possibly lie at a moderate depth and extend westwards for some distance under the Solway Firth. Within the faulted basin between Abbeytown and Kirkandrews-upon-Eden the seams will lie at the greatest depth, perhaps not less than 2,400 feet. At and south-eastwards from Carlisle carboniferous rocks can be reached at from 1,500 to 1,600 feet, but whether these rocks in the neighbourhood of Carlisle will contain workable coal seams or not it remains for the boring machine to prove. The PRESIDENT said he thought the members would agree that Mr. Russell's paper was a very interesting description of the subject and a very valuable one for the Institute. (Hear, hear.) Mr. W. FLETCHER asked if Mr. Russell was of opinion that the new Brayton pit was on the north side of Crosby fault. Mr. RUSSELL said that was what he understood. Mr. FLETCHER was reluctant to differ with so high an authority as Mr. Russell, but his opinion was that the fault on the north side of that pit was a branch from the main fault which ran along the valley of the Ellen and stopped perhaps at No. 3 Brayton Colliery. He thought the main Crosby fault was more on the north-west side of the new Brayton pit. Mr. OSWALD thought with reference to this fault that they were still on the upcast side of it and not on the downcast side at all. Mr. J. D. KENDALL, at the invitation of the President, said in regard to Mr. Russell's paper, he had nothing to add to what he said in 1883 when he read a paper on the structure of the Cumberland coalfield, at least not with regard to that portion of it to the north of Maryport. But he thought there was still work to be done by boring in that area, though from a geological point of view it was more a matter of speculation. The same remark also applied to the area south of Egremont. The tread of the carboniferous limestone between Rowrah and Bigrigg was to the northwest. Between Rowrah and Bigrigg, a distance of five miles, there was a great amount of fault up to the west. There was a very large fault running through the Cleator Moor coal, which struck a little south of St. Bees, and he, thought it was very likely that fault would continue to the sea and would have a very serious effect upon the continuation of the coal-field. The tread of the limestone also to his mind pointed in the same direction. It was very likely indeed that the coalfield would be further out to sea than Mr. Russell expected. In his paper he said that the probabilities were they would find the coal extending inland for about a mile and a half from St. Bees. At Bigrigg, which was only two miles from St. Bees, they had the thick of the limestone, and bearing in mind the number of faults crossing the band of limestone up to the west between Rowrah and Egremont, he thought it was extremely likely that they had not got the last of these faults but that there were others hidden underneath the red sandstone, and it was also extremely likely that these faults were repeated under the St. Bees red sandstone, and that they would find the coal measures more affected under the sea than Mr. Russell expected. Mr. R. W. MOORE also spoke, referring to the rumoured find of coal at Bootle in 1890, which rumour he found to be based merely on the fact that Mr. Geldart, the owner of the Hycemoore Side estate, in cutting a drain, had cut a spring three years previously and after the water had drained off a lot of small coal came away. It still remained, however, for deep boring to ascertain whether the coalfield extended that far south of St. Bees or not. In regard to the coalfield north or Maryport he agreed with Mr. Oswald that the main fault had not been reached in the Brayton Domain Colliery. Mr. W. THOMAS said that if, as Mr. Russell assumed, the Brayton deposit in the new pit is on the north or downthrow side of that fault, how was it that both the No. 3 pit, which was on the south side, and No. 4, that was on the north side, was practically on the same level with the north fault? If the fault that crossed that region was supposed to be the big fault, that seemed at once to prove that the new pit, No. 4, was on the upthrow and not on the downthrow side of the fault. Mr. PEILE said that in regard to the coalfield south of Whitehaven, it had always appeared to him in looking at the map of the coast that the coalfield might extend further out to sea perhaps than Mr. Russell stated and even to the North Wales coalfield. Mr. RUSSELL, in replying to the criticisms on his paper, said that with regard to the fault at Brayton, he pointed out in the paper that the fault was not one great fault but probably a series of faults, and that the fault which they met at Brayton was the first of the series. A vote of thanks was awarded to Mr. Russell on the motion of the PRESIDENT, seconded by Mr. T. E. FOSTER. Miss-Fires. Mr. J. D. KENDALL read a paper on this important subject: In working the haematite mines of the Whitehaven district, where large quantities of powerful explosives are used, miss-fires are a frequent cause of injury to the miners, injuries that are sometimes fatal, and therefore the subject of this communication seems to the writer one which the Institute might very properly consider. The principal explosives used in the Whitehaven district at the present time are nitro-glycerine compounds; of these gelatine-dynamite is by far the most largely used, but blasting-gelatine and gelignite are also employed though in smaller quantities. The total quantity of these explosives used in the district annually, at the present rate of working, is about 110 ton, and the number of shots fired about 880,000. The number of miss-fires may probably be taken on an average at 6.700 per annum. The usual method of charging the holes is to put the explosive into the hole first, the last cartridge having the cap in it, then to stem with a more or less clayey material to the top of the hole. In very wet ground water alone is usually employed for tamping. Miss-fires arise either from defective materials or bad workmanship. Defective Material. Miss-fires from defective materials may arise as follows :— (a) Inferior explosives, arising in many, if not most, cases from exudation of the nitro-glycerine. This is a defect, however, which is fortunately not of very frequent occurrence now. (b) Inferior detonators are also met with occasionally, but not often. (c) Defective fuse. — This is the most abundant source of the miss-fires which arise from the use of inferior materials. Even in the fuse of first class make there are sometimes found lengths which for 2 or 3 inches not a trace of powders to be seen. Fuses of this description may be most dangerous. For even if it should eventually "run" it must "hang fire" more or less, which may so deceive the miner as to lead him back again into his working merely to be shot. A miner should never return to a working in the case of a miss-fire, unless he has heard the cap explode, before the expiration of about 20 minutes. Defective Workmanship. Mr. Kendall showed that miss-fires from defective workmanship may arise in several ways :— (d) The detonators may be so insecurely fixed on to the fuse that in course of stemming the two may be separated, especially if the swab-stick be rather too thick and draw back the fuse during the operation of stemming. In such a case the fire may not reach the detonating material. (e) In wet ground it is necessary to grease the cap, that is, to fill up the space between the sides of the cap and the fuse with tallow so as to prevent, water from gaining access to the inside of the cap. This is sometimes neglected or imperfectly done and miss-fires are the consequence. (f) The sawdust, with which the caps are filled as they leave the factory, may also cause miss-fires if it be not removed. Caps that contain only sufficient sawdust to barely cover the detonating material will explode, but 1 — l6th inch of sawdust will prevent explosion. Gently crushing the cap and the detonating material within it will not cause explosion. From whatever cause, however, miss-fires arise it will probably not be possible to prevent them altogether, although they may be greatly reduced in number, for we are not likely in the future, any more than in the past, to obtain, at all times, either perfect material or faultless workmanship. He had had shots fired in the presence of experienced miners, who were all in favour of heavy stemming, with various thicknesses of stemming, ranging, in the different holes, from 14 inches down to ½ inch, and these miners all agreed that the burden in each case was as well thrown as it would have been had the hole been stemmed up to the neck. Mr. Kendall had caused the holes made in a number of mines to be charged as he suggested, for several mouths, with complete success, miss-fires being now most simply and easily dealt with. Mr. J. L. HEDLEY (Newcastle), Government Inspector of Mines, said that important as many of the papers submitted to the Institute might be, it must not be forgotten that the primary object of the Society was for the prevention of accidents, and considering the large number of accidents occurring in mines by explosives and resulting in loss of life and serious injuries to so many people, it appeared to him that the subject of this paper was one that deserved their fullest consideration, more especially as it had been introduced by a member of the Institute who had had a long connection with the mining industry. The result of the experiments Mr. Kendall had made he believed if was his intention to embody in a code of special rules, which would be the means of reducing the number of accidents that occurred only too frequently from the use of explosives. He (Mr. Hedley) however asked for further information on the point of defective material and also whether any suggestion could be made to prevent the exudation of nitro-glycerine from which accident arose, and also whether miss-fires were not due to the use of frozen dynamite. Were they to understand that Mr. Kendall had proved from actual experiments that a charge of dynamite could be exploded simply with the cap placed on the top of the charge? It was quite true that shots missed fire from inferior detonators, but would it not be advisable to use a galvanometer and test each detonator before it was sent into the mine? Mr. Kendall said defective fuse was the most abundant source of miss-fires. Then why not take the bull by the horns and do away with the fuse and use an electric battery? He had no doubt that this suggestion might sound revolutionary to many miners, but if once adopted he felt sure that the change would never be regretted. (Hear, hear.) Mr. OSWALD (Inspector of mines) said he had investigated the greater portion of the accidents in the district in consequence of miss-fires for the last nine years, and in nearly all cases the accidents had been caused by the workmen themselves, either by driving things into the charges or by going back to the shots too soon. In some places there was a rule that the men should wait 20 minutes before going back, and where that was enforced there were very few accidents. Mr. G. SCOULAR corroborated what Mr. Kendall had said, and with regard to the suggestion as to the use of an electric fuse, he said that was not an infallible cure for miss-fires. Mr. W. THOMAS said that to fix twenty minutes for miners to wait before going back to a shot that had missed fire seemed to be drawing it a bit too fine. Probably an hour would be safer. A vote of thanks was awarded to Mr. Kendall for his paper. Working Of Hematite In The White-Haven District. A paper on the above subject by Mr. J. M. Main was taken as read. It described the working to the ores in the carboniferous limestone area of the Whitehaven district, which has not hitherto received much attention, giving a general idea of the usual methods adopted in working these ore-deposits. He made reference to all the varying conditions which are met with in the development and working of some of the mines. A paper on "The mining of the softer haematite ores of the Furness district," by Mr. H. Mellon, was read by the Secretary, and a vote of thanks awarded to Mr. Mellon for his paper. "Sinking with Rock Drills" was the next paper on the list, by Mr. Frank Coulson. It was taken as read. Improvements In Brick Kilns. Mr. R. W. MOORE contributed a paper on this subject to the following effect :— In an ordinary brick kiln the products of the combustion of the coal used in the process of burning are allowed, after circulating amongst the charge, to escape direct to the chimney without further utilization, and as the combustion is imperfect, resembling more or less destructive distillation, a large proportion of the volatile products passes unconsumed up the chimney, and is consequently wasted. Another disadvantage of using the old type of kiln is that excessive firing, entailing an unnecessary large consumption of fuel, and a considerable waste of time, is absolutely requisite to ensure that the whole of the contents are burnt, and thus the front part of the charge, that nearest the fire, is discoloured, whilst the material at the back is frequently under-burnt. A further disadvantage that the old kiln possesses is the difficulty of ascertaining when the moisture is driven off the stack of raw material and when the full heat may be applied. These disadvantages have been got rid of by the improvements which form the subject of letters patent (No. 3,343, 1890) taken out by Messrs. Fletcher, Brown, & Ure, of Seaton, near Workington, and which have been applied with marked advantage by the Seaton Firebrick Company to their kilns at Moorhouse Guards, near the town before-mentioned. These improvements in the construction of brick kilns consist in conveying what was hitherto waste gas (the result of the imperfect combustion of the coal consumed in the space left between the charge and the front of the kiln), after it passes through the interstices of the charge, into a combustion chamber, shared like a beehive, built at the back of the kiln, by means of three flues, as shown on the accompanying plan and section. Two plugs or valves admit a small proportion of air into the top and bottom of the combustion chamber, thereby raising the ignited gaseous mixture to a white heat, and bringing the brickwork intervening between the combustion climber and the kiln ensures that the charge is burnt as well at the back as at the front, and experience has shown that the charge is evenly burnt throughout. From the bottom of the combustion chamber the ignited gas is conducted by a flue passing immediately beneath the kiln, thus heating it still further along its entire length, into a main flue that traverses the full length of the range of kilns, whence it can be gradually admitted by regulating dampers into one or more of the adjoining kilns by branch flues that enter the front of the kilns, as shown on the drawings. In describing the modus operandi of the new kilns it is first of all necessary to explain that the entrance to the kiln is walled up after the coal has been kindled under each fire-hole. The admission of air is regulated by dampers at the fire-holes, and all the orifices on the front and the crown of the kiln are sealed up to exclude the admission of air. The practice is to admit the ignited gas by degrees in to the newly-charged kiln or kilns adjoining that in operation, and to turn the full heat on only when the moisture has been expelled from the raw material to be burnt in the other kiln or kilns. If none of the gaseous mixture is wanted at another kiln, the damper in the flue leading from the combustion chamber into the chimney flue is kept open and the damper for the underneath flue is closed. But when the ignited gas is required for another kiln, the damper in the connection between the combustion chamber and the chimney flue is closed to an extent sufficient to send round such a quantity as will dry the moist contents of that kiln; and the damper in the underneath flue is opened as well as the divisional damper in the main flue, and the dampers in the branch flues leading to the front of the kiln. After the moisture has, in this way, been entirely driven off, the damper in the passage leading from the combustion chamber to the chimney flue is shut down altogether, and the whole of the heated vapour is passed through the contents of the second kiln and the combustion chamber attached thereto into the chimney flue; or, if it is desired to dry the contents of a third kiln, it is only necessary to close, or partly close, the damper in the flue connecting the combustion chamber of the second kiln with the chimney flue, and open the damper in the underneath flue, when the current will pass by the latter under the second kiln into the main flue, and thence by the branch flues into the front of the third kiln in the same manner as before described. It has been found by experience that 6 tons of coal will, by the following process, burn the contents of one kiln completely, and dry and heat to redness the contents of another; and that it is necessary to use other 6 tons of coal in the second kiln in order to burn the charge in that kiln thoroughly. However, by the time that the charge of the coal in the second kiln is wanted the first kiln is done with; and the products of the combustion of the coal in the second kiln can be utilized exactly in the same manner as has been before described. And so the process goes on with the remainder of the kilns constituting the range. Under the old system each kiln at Moorhouse Guards colliery and brickworks held 8,000 best firebricks, which occupied 60 hours in burning, and cost £l for labour during that operation. The consumption of coal amounted to 16 tons, costing £4. The total cost of burning the kiln was therefore £5, or 12s. 6d. per thousand. Each of the patent kilns holds 10,000 best firebricks, occupies only 30 hours in burning, and costs only 10s. for labour. The coal consumed amounts to 6 tons of the value of £1 10s. The total cost of burning firebricks by the improved system is therefore only £2 a kiln, or 4s. a thousand. The saving effected by the new kilns in the cost of burning is therefore no less than 8s. 6d. a thousand. One of the new kilns can be used forty times a year, producing an output of 400,000 best firebricks, and effecting a saving of £170 during that period. It can be built for the sum of £100, exclusive of the royalty payable on the patent — little more than one of the old pattern would cost. The improvements can be applied to existing kilns of the old type at a mere nominal cost. The improved process of burning has been applied with equal success to the manufacture of common bricks by the Seaton Firebrick Company, and at a much reduced cost. By the old method the burning of common bricks cost 5s. 6d., whereas they can be produced with the patent kiln at a cost of, at most, 1s. 6d. a thousand. Ten of these improved kilns have been in use at Moorhouse Guards for the last three years, and in addition to turning out the best class of firebricks have produced large quantities of fireclay blocks for the lining of blast-furnaces, cupolas, tuyeres, stoves, etc., where intense heat has to be withstood, at various iron and steel works in the district. The following is a copy of an analysis made recently by Mr. W. Bedford, then of the Whitehaven Haematite Iron & Steel Co., Ltd., Cleator Moor, of a brick burnt in one of the patent kilns at Moorhouse Guards, showing clearly the refractory power of the firebrick to resist great heat :—
Mr. J. D. KEDALL'S paper on "Description of the Haematite Deposit worked by the Salter, Eskett, and Winder Gill Mines, and the methods of working them," was next on the list, and it was agreed that it should be read in connection with the excursions when the party visited the Eskett district in the afternoon. Historical Sketch Of The Whitehaven Collieries. Mr. R. W. MOORE contributed a paper on this subject, which was read when the members visited the mines at Whitehaven :— Descriptive accounts of the Whitehaven collieries have been published from time to time, and the following may prove interesting to many of our readers. The present workings of the Whingill collieries may be said to be almost wholly confined to the under sea coal. It must not, however, be supposed that all the land coal has been exhausted. Large areas of solid coal and of coal standing in pillars still remain to be worked. The pillars in the Whingill side were left because at the time they were formed it was thought impracticable to work them. In 1812 Mr. Buddle suggested in a report that the experiment of working these pillars should be tried. Excepting a few taken out in the main band near Windsor High, and subsequently the pillars in the same seam in the Russia district of William pit, under Bransty, Mr. Buddle's suggestion does not appear to have been followed, and the Whingill pillars still remain to be worked. On the Howgill side the pillars were doubtlessly left for the support of the levels or water-courses, to which reference will be made hereafter. At Croft pit, the most southerly of the present working pits, part of the Permian series is found to overlie the Coal-measures. The pit is, as a matter of fact, sunk through the Magnesian Limestone, which is about 20 feet thick, and an underlying breccia only a few feet thick. Immediately to the south these members of the Permian group dip under red shales or marls (containing beds of gypsum) which, in their turn, dip under the great mass of Permian sandstone that forms the promontory of St. Bees Head. The St. Bees Grammar School, coal and that lying to the south of it is covered by a great thickness of Permian measures. The following account of the principal seams passed through in King pit, on the Howgill side, said to have been the deepest pit in the kingdom in 1793, will probably suffice to convey a general idea of the depths and thickness of the various seams met with in the Whitehaven collieries :—
With the exception of a borehole put down 60 fathoms below the six-quarter seam, near Wellington pit, in 1866, nothing is known of the strata beneath that seam at Whitehaven. The borehole proved at 48 fathoms a seam supposed to be the Harrington four feet, and if that surmise should prove to be correct, the Carboniferous limestone may be found at a further depth of 59 fathoms below the seam last mentioned. The site selected for a pit close to the sea shore, for the purpose of winning and working, was Saltom, close to high water mark, and a commencement was made with the sinking in 1729. This was the fifth great winning of the Whitehaven collieries. The shaft was sunk oval, 10 feet by 8 feet. Saltom pit was completed to the main band, a depth of 76 fathoms, in the year 1731. At the pit top a fire engine, with a 12 feet boiler, a cylinder 40 inches in diameter, and a pump 7 inches in diameter was erected. This engine was replaced by another in 1782, which continued to work until the year 1867, when it was broken up, and the water pumped at Wellington pit. In the year 1832 the great Saltom pumping engine was supplemented by a high pressure engine with a cylinder 2 feet 11 inches diameter and 7 feet stroke, working 10½ inches pumps. There is every reason to believe that the coal worked under the Solway at Saltom was the first worked beneath the sea in the world. The sea-coal at Saltom, and afterwards at William and Wellington pits, was worked free of royalty until the year 1860, when the Crown put forward a claim to the minerals lying below low water mark. From 1860 until 1880 the submarine coal was worked under a Crown lease, when Henry, Earl of Lonsdale, purchased the minerals under the sea down to the bottom of the coal-measures, and for the distance of ten miles seawards. At Whitehaven the first application of the steam engine, working on to the rope-roll shaft with a crank and connecting rod off the beam, was made at Davy pit, on the Whingill side, where an atmospheric engine was erected by Messrs. Heslop Millward, of the Seaton Iron Works, near Workington, in 1791. This engine was afterwards removed to North pit. This type of engine was patented in 1790 by Mr. Heslop; and was extensively used at other collieries in West Cumberland. In 1800, James pit, Whingill colliery, was sunk; but the great work of which Mr. Bateman was the author was the sinking of William pit, on the shore, near Bransty, on the north side of the harbour. This may be termed the sixth great winning of the Whitehaven collieries. It was begun in the year 1804, but was not completed till 1812. In 1811, Mr. Bateman, the manager retired, and was succeeded by Mr. John Peile, who had been trained from his youth in the Whitehaven collieries. Mr. Bateman died in 1816, in the 67th year of his age, and was buried in Trinity Church, Whitehaven. In 1830, the pits working during the week ending 5th January were :— Howgill colliery: Saltom, Moss, Kells, Croft, and Wilson pits producing 2,062 tons of coal. Whingill colliery: William and North pits producing l,440 tons of coal. The selling price of coal at the staiths was then 4s. 4d. a ton. In 1812, Mr. Taylor Swainson, engineer for the Whitehaven collieries, tried his invention the "iron horse," or locomotive engine, on the colliery wagon-roads. The engine answered admirably, but its use had to be discontinued owing to the track not being strong enough to bear it. It has been said that Mr. Taylor Swainson was the real inventor of the locomotive. Under Mr. Piele's direction, the Whitehaven collieries made great progress. In 1813 he constructed the Howgill surface incline down to the Howgill staith. In 1818 he sank Croft pit from the main band down to the six-quarters seam, and drove therefrom a level drift until it cut the main band seaward. In 1819 he did a similar thing at Saltom pit. He sunk a new shaft at Duke pit from the surface to the six-quarters, and also James pit from the main band to the six-quarters. In 1832 he began the Paston drifts and the Countess pit. The Countess shaft furnishes a splendid example of pit walling; and it is also remarkable for having two stone brattices built at right angles, to each other and dividing the shaft into four compartments. Each course of the brattice is arched and let into the side of the pit. The Countess pit worked until 1863, when it was abandoned, and when also the Parton drifts were stopped. Wreah pit was also sunk during Mr. Peile's tenure of office. But the undertaking with which Mr. Peile's name will always be associated is the sinking of the Wellington pits which were begun in 1840. In 1843 one of the pits was down to the main band, and the other to the bannock band; both reached the six-quarters coal in 1845, and thence level stone drifts were driven sea-ward and intersected the main band at a distance of 900 yards. The Wellington pits may be fairly denominated the eighth great winning of the Whitehaven collieries. Mr. Peile proposed to sink the pits to a further depth of 160 fathoms, a total depth of 300 fathoms from the surface. The last 100 fathoms would have been in the Carboniferous limestone. From the bottom of these pits, in the limestone, he proposed to drive a pair of level drifts westward until they intersected the six-quarters coal and main band, and finally the Bannock band at a distance of 4,500 yards from the shafts. The first 2,000 yards of these drifts would have been in limestone. Mr. Peile commenced the manufacture of coke and patent fuel at both William and Wellington pits, but there was no demand at that time for those products, and during the term of office of his successor, these branches of industry ceased. He also, in 1839, introduced the use of screens at the Whitehaven collieries. In 1841, a fan was erected at the upcast at Duke pit for the ventilation of the workings in the main band and six-quarters seam at that pit. The fan was 8 feet diameter and 4 feet wide. It was driven by a high pressure engine with a 12 3/8 inches cylinder by 3 feet stroke, and produced 23,000 cubic feet per minute. This was the first attempt at mechanical ventilation at the Whitehaven pits, but it could not be considered a great success; and the collieries continued to be ventilated by underground furnaces, as hitherto, until 1870, when the Guibal ventilator was erected at Duke pit on the advice of Mr. G. B. Forster. During Mr. Peile's reign at the Whitehaven collieries the output reached about 250,000 tons a year. In 1818 the average selling price of coal was 9s a ton, but in 1843 it was 6s a ton, 7s 6d a ton, excluding small coal. On the 19th of March, 1844, William, the second Earl of Lonsdale, died in the eighty-seventh year of his age, and was succeeded by his eldest son William, Viscount Lowther, who had for some time past taken his father's place in looking after the Whitehaven colliery and estates. In 1847, Wilson pit, and in 1848, Saltom pit, ceased drawing coals. In 1848 Mr. John Peile retired, after a long and faithful service. He was succeeded in the management of the collieries by Mr. Peter Bourne, who resided at Somerset House, which had been purchased by Lord Lonsdale after the damage that had been done to it in 1791. Mr. William Anderson, of South Shields, was retained as consulting viewer. On the 17th of January, 1855, after a few days' illness, Mr. Peile died in the seventy-ninth year of his age. He was interred in St. James' churchyard. A most important matter in connection with the development of the collieries occurred whilst Mr. Bourne was agent. About the year 1849 the workings in Croft pit main band had reached the downthrow fault, known as the St. Bees dyke, that had already stopped the workings in that seam, in Wilson pit to the south. It was thought by many that the southern extremity of the West Cumberland coal-field had been reached, and doubtlessly they were induced to form this opinion from the fact that Permian sandstone puts in an appearance above the Coal-measures not far off. A level drift had been driven through the fault for a distance of upwards of 300 yards, and several boreholes had been put both up and down. Eventually in 1862 a borehole at the end of the drift in the school royalty proved the main band at a depth of nearly 53 fathoms. So important was this discovery considered that the journal of this bore was engrossed, in duplicate, on parchment, and signed by Mr. Stephen Toward, borer ; Mr. W. Anderson, the consulting viewer ; Mr. Bourne, the colliery agent; Mr. H. Mulcaster, viewer; and Mr. John Ellwood, the overman of the pit. This fault was afterwards crossed seaward, where the throw was found to be so much less, and the Croft pit workings now extend nearly a mile beyond it. Nothing else worthy of remark occurred during Mr. Bourne's term of office except the fire that broke out in the six-quarters seam at Wellington pit on the 24th of August, 1863. At that time there were two underground hauling engines, with boilers, placed near to the level drifts, to which allusion has been made, leading from the six-quarters seam to the main band. The smoke from the boiler fires was conveyed by means of a chimney drift to Duke pit. This underground flue passed through the six-quarters coal, near Wellington pit, and it was there that the fire was discovered. It was thought by some that the fire originated in a chimney drift from the ignition of some soot by a spark, and that the fire thus created had penetrated through some crack in the arching to the coal. Others thought that the fire was the work of an incendiary. In this emergency the late Mr. T. E. Forster, of Newcastle-on-Tyne, was telegraphed for, Mr. Anderson, Lord Lonsdale's consulting viewer, having died in 1862. It was upon Mr. Forster's advice that this terrible underground fire was extinguished. How this was accomplished is too long a story to tell here in detail, although worthy of more than a passing notice. The means adopted may be briefly described as the sealing hermetically of the Duke pit, and the flooding of the entrance to the six-quarters seam at Wellington pit bottom. This latter operation was effected by putting in four dams, two in the drifts leading through to Saltom pit, and two in the drifts leading from the six quarters seam, at Wellington pit, to the main band seaward, and by pouring in the sea down one of the Wellington pits by means of a drift, fitted with sluices, that was driven from shore between high and low water marks. In addition, steam was blown through a pipe in the tight stage at one of the Duke pits. Although several attempts were made to open out the six-quarters district, where the conflagration was, it was not until 1861 that the fire was completely extinguished. It is worthy of note that this fire, which at one time threatened the safety of the whole colliery, was put out without loss of life, and with one or two minor exceptions, without accident or injury to any one. But the loss occasioned by the almost total stoppage of Wellington pit was great. Besides the loss of the six-quarters district, the workings to the dip, below the spending of the drifts seaward to the main band, were flooded owing to the leakage of the dams before-mentioned. Work was found for a limited number of men in the main band pillars in The King pit district, but it was not until 1872 that the water was got out of the dip districts so as to enable work to be resumed there. The pits working at the Whitehaven collieries at the time of the Wellington pit fire were Wellington and Croft pits on the Howgill side, and William and Wreah pits on the Whingill side. Countess pit had just been abandoned. After the death of Mr. Anderson, Messrs. T. E. Forster, G. B. Forster, and T. G. Hurst, of Newcastle-on-Tyne, were appointed consulting engineers, and on the resignation of Mr. Bourne in 1867, they took the direct management of the Whitehaven pits into their hands, having first of all Mr. Henry Mulcaster as resident viewer, and after his death Mr. Matthew Harper. During their term of office many improvements were made. The air courses were greatly improved, mechanical ventilation introduced, new haulage roads made, and new haulage engines erected at the pit tops. In 1870 the sinking of Henry pit was begun, and shortly after the William pit was put down to the six-quarter seam from the main band. On the 4th of March, 1872, William, Earl of Lonsdale, died, aged eighty-four years, and was succeeded by his nephew. Colonel Henry Lowther, in the estates and title. It was during the lifetime of Henry, Earl of Lonsdale, 1874, that, in accordance with the advice of Mr. G. B. Forster, of Newcastle-on-Tyne, his lordship's consulting engineer, a borehole was put down by Mr. Vivian, with a diamond rock drill, and proved the main band seam at a depth of 240 fathoms from the surface. This discovery is of vast importance. It proves the continuity of the coal from the Croft pit workings, which are about two miles off, and is a certain indication that an immense virgin coal-field lies both inland and seaward to the south. Description Of The St. Helen's Colliery, Workington. Mr. GEORGE SCOULAR also contributed a paper on the above, which was read when the members visited the Colliery named :— The proprietors of the colliery are the St. Helen's Colliery and Brick Works Company, Limited, of Workington. The lessor is the Earl of Lonsdale. There are two shafts 10 feet 9 inches and 11 feet 8 inches in diameter respectively, sunk close together on the sea coast at Siddick Station, about one mile north-east from Workington harbour. The royalty, not including that under high-water mark, extends to about 2,000 acres. The seams being worked are the ten-quarters, cannel and metal, little main, and lickbank; the depths being, respectively, 504, 714, 918, and 1,020 feet. The present area of worked ground is about 200 acres. The ten-quarters seam yields about 2 ft. 8 in. of clean coal, the cannel and metal about 7 ft., the little main 2 ft. 2 in., and the lickbank, about 2 ft. 2 in. The seams, especially the cannel and metal, are intermixed with bands of dirt, and are also, as is general in the Cumberland coal-field, considerably faulted. The seams are worked on the long wall system with the exception of the cannel and metal which is worked on the pillar-and stall system. Coal is raised at both upcast and downcast shafts. The winding-engine at the downcast shaft has two cylinders 30 inches in diameter and 5 feet stroke, with Cornish valves and a cylindrical drum 15½ feet in diameter. The ropes are 1½ inches in diameter. The cages are three-decked, one tub carrying ll½ cwt. being on each deck. At the upcast shaft the winding engine has two cylinders 26 inches in diameter and 5 feet stroke, with drop valves and cylindrical drum 14 feet in diameter. The cages are double-decked, with one tub on each deck. The pumping-engine, which is of the Cornish type with overhead beam, has a cylinder 60 inches in diameter, and 9 feet stroke, and actuates two lifts of pumps each 252 feet long, the upper one being 18 inches in diameter and the lower one 16 inches in diameter. The Guibal fan is 36 feet in diameter by 12 feet wide, and is driven by a single non-condensing engine, with duplicate cylinders. The hauling-engines are horizontal compound-condensing, with cylinders 16 inches and 30 inches by 2½ feet stroke, and are erected on the surface. They transmit their power by two band-ropes to the haulage stations underground in the lickbank and the cannell and metal seams. In the lickbank seam one of the band-ropes drives four clutch-pulleys, which are mounted on a vertical shaft, and gives motion to endless-ropes running at the rate of 2½ miles an hour along the roadways radiating from the haulage station. In the cannell and metal seam there is a similar arrangement of three clutch-pulleys driven by the other band-rope. There are two air-compressing engines, each having one steam and one air-cylinder 24 inches in diameter by 4 feet stroke; the compressed-air being used underground for dip-haulage and pumping. For screening and picking the coal there are three jigger-screens, each discharging the round coal upon a separate travelling table, where the dirt is hand-picked. The small-coal from each screen is conveyed by a travelling-belt to the small-coal bunker, from whence it is elevated to a revolving riddle, where it is sized, and is afterwards washed in the Coppee washery; the nut and coking coal being automatically discharged into the several bunkers, ready for loading into railway wagons or into the coke-oven bogies. A battery of 24 Coppee, forty-eight hours, six tons, coke-ovens has recently been put into operation, the gases from which fire two Babcock and Wilcox water-tube boilers. Description Of The Whitehaven Collieries. Mr. H. M. James contributed a paper on the above, to the following effect :— The Whitehaven collieries are the property of the Earl of Lonsdale, and are being worked under lease by the Whitehaven Colliery Company. The William, Wellington, and Croft pits are each sunk 840 feet to the six-quarter coal-seam, and each work the main band coal-seam at a depth of 600 feet. With the exception of a small district in Croft pit, leased from trustees of St. Bees Grammar School, the whole of the coal is worked under the sea, the average distance from the pit's bottom to the forehead being three miles. The coal is brought from the faces by different systems of haulage in the different pits. At the William pit the coal is brought from the Countess and Delaval districts by compressed air-engines placed at the top of the brows leading to those districts, and bringing the coal up by the endless-rope system to the main engine-plane, whence by combination of the endless and tail-rope systems the coal is brought in sets of from seventy to eighty tubs to the pit-bottom. It is intended to make this main engine-plane, which is now a single road into a double one very shortly, the necessary work being in progress. The output of this pit is 800 tons per day of 10 hours. The Wellington pit it situated on the south side of Whitehaven harbour. The main engine-plane, which dips at an angle averaging 1 in 10, is laid with a double road. At a distance of 9,000 feet in-bye the main haulage-rope works friction-gear, with two drums, from which drums the haulage-rope is taken into the two districts into which the work is divided. The tubs brought out by means of the friction-gear, are made up in sets and taken to the bottom along the main engine-plane by the endless-rope system of haulage in sets with bogies at either end. This pit also has an output of about 800 tons per day. The Croft pit is situated 1½ miles to the south of the Wellington pit, with which it is connected by a tramway along the cliffs. The workings are divided into several districts, whose roads converge on to the main engine-plane at the same point. From one district the coal is hauled, by friction-gear, on the endless-rope system with underneath attachment, and in another by the endless-rope with overhead attachment. The friction-gear is driven by the main haulage-rope, and the tubs, when delivered on to the main engine-plane, are made up in sets and brought to the pit-bottom on the endless-rope system in sets with one bogie in front. The output of this pit is 600 tons per day of ten hours. In each case the underground hauling is effected by engines placed at the top of the pits. An interesting feature at the William pit is the Newcomen and Watts atmospheric engine doing efficient work, the vacuum being produced from the exhaust steam of the fan engine. The pits are all ventilated by Guibal fans. There are 76 beehive coke-ovens at work at the William pit, and 50 additional coke-ovens are being built. The small coal is washed, and ground in a Carr disintegrator before being put into the coke-ovens. The produce is a hard coke, well suited for blast furnace purposes. Six boilers are attached to the existing coke-ovens, and three more are being fixed to the coke-ovens in course of erection, the waste heats from the coke-ovens being thus utilised to material advantage. In connection with the meeting of the Institute at the Grand Hotel, Mr. E. Telfer, of Brackenthwaite, Whitehaven, had on view his new patent screw grip for rope haulage in mines, &c. The new grip was critically examined by many of the practical engineers present, who congratulated Mr. Telfer on having produced what they feel sure will become of the greatest possible service in all cases where rope haulage is required. "The history and description of the Greenside Silver-lead mines," by Mr. W. H. Borlase, will be read to-day (Friday) when the members visit the Patterdale and Lake district. Luncheon was partaken of at the Grand Hotel, by invitation of the Whitehaven Collieries Company, and afterwards the excursion parties set out. To-day (Friday) the members of the Institute visit Troutbeck and various places in that district.
Newspaper transcript kindly provided by
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 28 Nov 2022
|
Search |
|
|||