8th August 1846, Page: 4, Column: 3
The Tyneside Manufactories — No. XV
Messrs. Spencer and Sons' Steel Works
At the village of Newburn, about five miles west of Newcastle, on the North
bank of the Tyne, there is one of the most interesting factories —
because, almost the only one of its kind — in the north of England. It is
beautifully situated by the side of a stream, in a retired corner of a rocky
dell, close to the Walbottle colliery. In this quiet spot, the manufacture of
steel, files, and springs, and other articles of the same material, has been
conducted, on an intensive scale, for twenty-four years; and, so prosperous is
this branch of industry, which is scarcely known in any other quarter than
Sheffield, that the workmen at Newburn, upwards of one hundred in number, are
at present employed at "day-and-a-quarter" time.
The steel, with which the files and other articles are manufactured, is made
from Swedish and Russian iron, the iron of this country being deficient in
strength of body. The iron is placed in a furnace, in quantities of about
thirteen tons, along with charcoal, from which it gathers additional carbon.
The iron and the charcoal are placed together in layers; and, after being
heated for six days, and allowed ten or twelve days to cool, it comes out of
the converting furnace as steel. It is then in a "blistered" or
brittle state ; and, on being sufficiently cooled, it is taken to the
rolling-mill, where it is rolled into bars for springs and other purposes. A
great portion of the best marks of "blistered" steel, however,
instead of passing through the mill on coming from the furnace, are broken in
pieces, put into crucibles, containing thirty-four pounds each, and heated to a
boiling temperature, and then poured into metal moulds. This is called cast
steel ; but, before applying it for files and the finer kinds of cutlery, for
which it is intended, it is put through the rolling-mill and shaped to various
sizes. Part of it also goes to the tilt-hammer, for cutlery and turning tools;
and, in this latter state, is called "tilted steel." "Shear
steel," of which large scissors and other useful articles are made, is
manufactured from the blistered bars, which are heated in a furnace till fit
for "welding," and then, being doubled up in layers, are designated
"double shear." The only difference of the "double" and the
"common shear," is that the former passes through one or two
additional processes.
On returning to the cast steel, we find that after coming from the
rolling-mill, the quality intended for making files, is taken to the
file-forger, who makes them to any shape or size required; but being still too
hard for the purposes to which it is to be applied, it is placed in an
annealing furnace, and there softened. It next comes in contact with the
grinding machinery, which is driven by a powerful wheel, moved by water power;
and, being thus smoothened and brightened, the file is ready for the cutters,
who cut the small regular notches and crossings which give sharpness and power
to the file. This process, though seemingly tedious and troublesome, is
performed with a degree of expertness and regularity that surprises a stranger.
The only tools used are a chisel and a hammer, the former being carefully
tempered and very sharp, so as to cut with ease the work required. Some of the
larger files, called "rasps," and used for horse-shoeing, are cut
with "punches." The men work in a sitting posture, and the seat on
which they sit across is technically called a "horse." In front of
them are a block and small anvil, on which the cutting process is performed. In
consequence of the closeness and delicacy of cutting in some files, great skill
is requisite in the art; and an apprenticeship of seven years is exacted, in
order to produce efficient workmen. After being cut, the files pass through
several other processes; they are heated in a blast fire — cooled in
water — brushed quite clean, then dried before a fire, and, finally,
carefully oiled, made up in parcels of a dozen each, and thus sent to market.
Files, though the chief, are not, however, the only articles manufactured by
the proprietors. The railway system has increased the demand for steel, to a
very great extent, and particularly for springs; the steel that is made into
springs at these works, on coming from the rolling-mill, is drawn to the proper
length and shape, then taken to a machine, which is driven by steam power,
where the holes are punched, studded, and the ends cut, and afterwards they are
taken to the "fitters," where they are tempered, and fitted to the
proper shape for locomotive engines, railway carriage, &c., by experienced
workmen. These are not used by the proprietors, but supplied to such factories
as those of Messrs. Stephenson, Messrs. Hawthorn,
Messrs. Longridge, and
various other engineers in all parts of the kingdom, and on the continent.
Indeed, every description of steel goods required by engineers and other
tradesmen, is made at this factory and made, we are glad to learn, in such a
manner as to have earned, both for the proprietors and the district, a
deservedly high reputation. The works are well arranged, compact, and
commodious ; the machinery is driven both by steam and water power ; and the
factory, altogether, is one of the most important and valuable that we have
seen in the neighbourhood. The proprietors, we understand, have an office for
business in Sussex Street, Forth Street, in this town.
 |
 |
|
Names mentioned in this article
|
 |
 |
| Name | Age | Occupation | Notes |
| Hawthorn, — | | Manufacturer | |
| Longridge, — | | Manufacturer | |
| Spencer, — | | Manufacturer | |
| Stephenson, — | | Manufacturer | |