Logo Museum
Museum
Friends of Durham Mining Museum
Events Calendar
e-Books and Books for sale
Photograph Gallery
Document Archive
Master Name Index
What's new in the site
Mining
Mining History
Colliery Index
Colliery Maps
Company Overviews
Who's Who
Mineral Information
Managers Certificates
Educational Material
Bibliography
Statistics
Workers/Employee Lists
Notes for Family Historians
War Service information
Disasters
Disaster Reports
Names of those killed
Name Index (Local!)
Name Index (Rest of UK)
Disasters in the 1700s
Disasters in the 1800s
Disasters in the 1900s
Memorials
Awards for Gallantry
On this day ...

Links to other sites of interest
Industrial Heritage Days Out
Former www.pitwork.net web site

Index to site

Contact and address details

Share Page with Social Media

Share on Facebook

Share with Reddit

Share on Delicious

  Disasters - Names Return to Index Disasters - Names  
/ \
Date:  27th March 1907
Colliery:  New Lambton, D Pit
Company:  Lambton Collieries Ltd.
Cause:  Accident caused by electricity
Lives Lost:  1
Category:  

Description

The accident at Burnmoor occurred on 27th March and caused the death of the Master Shifter and injury to the machineman. The face being cut was practically a straight one and was 250 yards in length. The machine was of the bar type mounted on runners or skids, and driven by an alternating current of 500 volts. The motor was rated at 80 h.p. and took 25 amperes of current. The current was taken to the motor from the gate-end switch box by means of a trailing cable, which was made up of three conductors and a separate earth return. The travel of the machine along the face was automatically produced by means of a steel wire rope wound on to a drum actuated by gearing on the machine. The end of the rope was taken from the drum round a pulley-block fastened by a chain to a short length of steel rail placed vertically between the roof and floor of the seam, and thence back to the frame of the machine to which it was attached. By the revolution of the drum by the gearing, the rope was wound on, and the travel of the machine along the face thus attained. Prior to a machine being set to a cut a length of face, preparations are made by stonemen and shifters. The whole length to be cut is freed from rubbish and the roof supported by planks, one end of each plank being let into the coal and the other end supported by a prop. Chocks of hard wood are also set up between the props net the goaf. Between the line of props and chocks on the one side and the face of the coal on the other, there is a clear space from four to five feet wide by the thickness of the seam, viz.: about 4 feet. The machine itself occupies a space of 9½ feet by 4 feet by 20 inches.

At the time of the accident, the machine was cutting from right to left, and a length of 56 yards of face had already been undercut. The depth of the cut was 5 feet. The trailing cable was fastened down to the side of the machine net the goaf, beneath a projecting bracket, by means of a piece of hemp rope. By this means, so long as there was slack cable behind the machine, the cable is kept from being squeezed between the timbers supporting the roof and the machine. In the present case, this piece of rope was, very shortly after the accident, found cut in two, or rather squeezed in two, and the cable jammed tight between a chock and the projecting bracket on the framework of the machine, and one of the conductors laid bare. The cause of the cable getting up between the chock and the projecting bracket on the framework of the machine wad that, contrary to Section V, Rule 7, of the Special Rules for the Installation and Use of Electricity in Mines, it was being dragged along by the machine and was in consequence taut. This taut state of the cable had caused it lift from beneath the projecting bracket and the hemp rope, which had previously kept it there, had come against a chock and been flattened in two. The squeezing off of the insulating material, and the consequent contact of the bare conductor with the machine, electrified the machine itself, the hauling rope already referred to, and the ground in the immediate vicinity. The man attending to the machine had not been aware of what had occurred and was in the act of working a ratchet lever to adjust the height of the machine, when he received a shock and was thrown down between the machine and the face. There he stayed not daring to move, but shouting for help. The Master Shifter happened to be near and he came forward to the machine, when he received a shock and was thrown down. His lamp was extinguished and he then turned and crawled along the face, in the direction of the fixed pulley-block, with the intention of reaching the gate-end switch box to switch off the current. Crawling as he was in the dark, he unfortunately touched the hauling rope and from it received a shock which proved fatal to him. Other men, hearing the machineman shouting, came towards the machine, and seeing, as they afterwards said, "fire flying in all directions," hastened to the gate-end box and switched off the current. They then went in towards the machine, but, on passing about two yards beyond the fixed pulley-block, they found the Master Shifter, clutching the hauling rope with his left hand and with his left leg beneath it, dead. The machine attendant had also received a shock but not a fatal one. There were no marks on the Master Shifter.

As has already been explained, there was in the trailing cable an earth return. This consisted of 19 wires of pure copper, 26 S.W.G., and was connected to the frame of the coal cutter and to the gate-end box, and thence, by way of the armouring of the main cables, to the earth plates at bank. The method of connecting the earth return to the frame of the coal cutter was by means of a pin on which was a collar. The end of this pin was threaded to screw into a hole in the coal cutter frame, and it was intended that on the pin being passed through a brass plate, to which the earth return wire was soldered, the shoulder, or collar, should press against the brass plate and so make a connection. As a matter of fact, the hole in the machine frame was not big enough to allow of the pin being screwed deep enough to permit the collar on the pin to touch the brass plate. The side of the pin however would, in all probability, touch the inside edge of the hole in the plate as it passes through, but this would not make a firm contact or connection.

The trailing cables were not in one length from the gate-end box to the coal cutter, but were in lengths of 70 yards. These lengths were joined together by specially arranged junction boxes, which, however, were so made that the connection between the earth return carried in each length of trailing-cable was not automatic but had to be made by placing in position an iron bridge-piece or staple. Further, it was possible, and easy, for this bridge-piece to be so placed as not to connect the earth return in each length of trailing-cable. This is due to the fact that there are two hole on each of the two parts of the junction box, four holes in all, and it is only by connecting the correct two of these holes that the passage-way for any leakage of current to earth is made continuous. If the bridge-pieces were put into one of the proper holes and one of the wrong ones, or into the two wrong ones, as might very easily occur, the provision of an earth return, and so the earthing of a portable motor, would be rendered of no effect.

In the present instance, I think that the provision for safety, i.e. the earthing of the coal cutter motor, which, being a portable motor, is not required by the Special Rules, was inoperative ; and that this was due either to the connection direct to the frame of the machine being faulty, or to a bridge-piece connecting two lengths of earth return in the training cable not being in its proper position.

The direct cause of the leakage of current was the fact that the trailing cable was allowed to drag to be dragged along by the machine, and, as a consequence, was squeezed between the coal cutter and a chock and the insulating material thereby scrubbed off one of the conductors.

Since the accident steps have been taken to make the passage of the trailing cable along the face as automatic as possible, and to so arrange the junction boxes in the trailing cable that the connections of the earth return cannot possibly be otherwise than correctly made.

Source: 

1907 Mines Inspectors Report (Cd 4045), Durham District (No. 4) by R. D. Bain, H.M. Inspector of Mines, Page: 21 Where to find this report



Fatalities



Individual page 

Smith, David, aged 30, Master Shifter, he was electrocuted by a leakage of current from the trailing cable of a coal cutter [Sunderland Echo reports: accident - 27 Mar 1907], Buried: Houghton Cemetery

 
All names found
 

Those names marked with image, have a web page providing individual details of the accident, the page may also include a photograph of the deceased. Click on the image symbol next to the name to see the web page.

 

Return Return   Return Return to Top

mail
Mail:
Webmaster
Back
Back
Home
Home
Open Government Licence   Contains public sector information licensed under the Open Government Licence v3.0.

Copyright © 1999-2024 by The Durham Mining Museum and its contributors
Registered Charity No: 1110608
Page last updated: 31 Dec 2022

Privacy Policy
 
Terms & Conditions
 
Search
Search
Print
Print