|
In 1810 the treatment of ore in the Pennines followed a general plan almost everywhere alike. Bouse was sorted into ore, waste, and mixed, and the mixed passed over a riddle of about 2 in. mesh. Mixed oversize off the riddle went to the knock stone and was there reduced by buckers to coarse "sand." The riddlings went to the swilling tub and were jigged on a I in. mesh sieve, then hand picked, ore being sent to the ore heap, mixed material to the knock stone, and the slime to the buddlers. The washers took all the produce of the knock stone and dressed it, on jigging sieves, into two or three grades. All material passing through the sieves, "smitham" was accumulated in the tubs and later was sent with the slimes from the swilling tub to he buddled. Jigging buddles and trunk buddles were both used. The London Lead Company found it extremely difficult to improve the organisation of their mines while the washing was still done more or less independently by crowds of boys and women who worked mainly in summer, and then were often laid off by drought or storm. This seasonal and casual character of their work tended to make them very unreliable. The company therefore took the whole of the washing into their own hands, and made the washer boys into full time employees, giving them work underground during bad weather and the greater part of winter, and thus keeping them much more under their own control and discipline. To overcome stoppages due to drought, large reservoirs were built where possible and washing was concentrated at a few central floors. The introduction of iron railways into all their mines and between the mines and washing floors made it possible to systematically plan their processes on the lines of a modern "flow-sheet." During their reorganisation advantage was taken of a recent invention, that of the crushing rolls, to reduce very largely the number of boys and girls employed as buckers. These rolls were first introduced by Taylor, at Wheal Crowndale, near Tavistock, in 1804, where one pair of rollers, 24 to 30 in. in dia., were driven directly by a water wheel. (Fig. 3.) The London Lead Company altered the arrangement of the rollers and in 1816 built three of their new pattern crushing mills, one at Lodgesyke in Teesdale, and two at Smallcleugh and Rampgill, Nenthead. Their new crushing mills had three pairs of rollers each, one pair fluted and the others smooth, the rolls being 27 in. in dia. and 12 in. long; a pressure of 5 tons was maintained on each pair of rolls by means of weighted levers. Each mill could deal with 80 tons of material in a 10 hour run. They cost £1,500 each, but the annual saving in labour as against the "bucking" and hand breaking was nearly £400 at each mill, so that they paid for themselves in four years. The Lodgesyke washing floor during the first year's run saved nearly £2,000, and as its cost exclusive of the mill was only £1,700, it proved a very profitable reorganisation. By 1820 the reconstruction of the dressing floors was complete and many new processes were in operation. Bouse from the mines was now delivered into kilns or house teams which were large masonry built hoppers, rather funnel shaped, with an outlet at the front base through which house could be raked over a grate of iron bars. A stream of water was carried into the kilns and ran out with the house on to the grate, thus serving to wash the house as it was raked across the grate. From beneath the grate an inclined trough or launder ran to a settling pit. Fine dirt and ore were washed through the grate, and the coarse washed material lying on the grate was raked on to the picking floor, hand picked there, and then sent to the crushing mill. Crushed ore, heads and middles from the grate pit were then worked up on the "brake sieve," i.e., a jigging sieve worked by a lever. (Fig. 4.) A in. mesh, rectangular sieve was suspended by two upright arms from a long lever so arranged that the sieve could he jerked up and down vertically in a large tub or tank of water, locally called a "hotching tub." In action this was almost identical with that of the hand-jigging sieve, but one man at the brake sieve could handle four times as much ore per day as with the hand sieve. The "smitham" passed through the brake sieve into the tub, and from there was sent to the running buddle. Slimes from all processes were sent to the Dolly tub. This was a semi-mechanical keeve, in which the tossing and stirring was done by a pair of paddles fitted on a vertical shaft ; these paddles could he stirred rapidly by means of a geared handle and, when necessary, lifted clear of the tub. This keeve was introduced in 1816, and shortly after was made entirely mechanical, the dolly being driven through bevel gear from a water wheel, with a trip hammer knocking the tub side and base to help the "packing." In 1818 and 1819 considerable famines were experienced in the north, and the London Lead Company's washing floors were besieged by crowds of women, boys and men, demanding work of any kind to keep them from starvation. The company built up a large organisation to provide food at the lowest possible price for the district ; they also attempted to find employment for all people with family responsibilities. To relieve the situation, large numbers of men were put on to building dams, water courses, etc., making water wheel cases, and entirely rebuilding the washing floors in the company's area. This coincided with many improvements in smelting practice, and with a large program of road building and tramway extensions linking up all the company's mines in Weardale, Teesdale, Alston Moor and Westmorland. Consequently when business recovered, their production was sent up by leaps and hounds, both in quantity and quality. On this tide of increased production many improvements and new inventions were brought into the washing floors. A Cornishman, Tratham, had been employed in 1816 to build the first stamps in the north, at Nenthead, and in 1818 he introduced at Nenthead and Stanhope the use of the slime pit for further settling and concentrating the buddle washings. A buddle was soon after developed for dealing with slimes direct, and proved very successful. In 1826 the minutes of the company notice, under four heads, considerable improvements now made and proved on their crushing mills.
The agent at Dufton, Westmorland, reported to the Court of the company that "Here also we found proof of the superiority of our washing in being able to employ with profit, a number of boys to rewash old wastes that have been accumulating 40 years." In the following year, 1827, the buddle in use at Nenthead was considerably improved so that it was reported "when the attempt was first made to wash slime ores by this machine, it cost 42sh. per bing; the present cost is 7sh. per bing." The chief improvement was the substitution of knives or paddles on a wheel frame, driven from a water wheel, and so arranged over the buddle that the slime ores were stirred up and moved with great regularity across the buddle, the whole being capable of very close regulation to suit any kind of slimes. Hand buddles were still continued for rewashing the old waste, nineteen being still in operation on the London Lead Company's floors in 1827. "The waste that used to be thrown out as valueless is now washed on the large mechanical buddle at a cost of 4s. 3d. per bing. The company is the sole introducer of this improvement." In 1828 a series of improvements were made in ore washing, and can be regarded as the herald of the modern period. These were the introduction of the modified round buddle, the invention of the shaking table, and Petherick's hydraulic jigger. The origin of the round buddle is not at all clear but there is suggestive evidence that it was first used in the north of England; quite possibly it was the "improved buddle" used by the London Lead Company in 1826. Stagg, the company s agent in the north, had made a model of a new kind of buddle in 1817, and had frequently modified it, but there is no record that he tried it out until later. From 1825 the buddles are differentiated in all their reports as hand buddles and machine buddles. In that year, 1825, Taylor, the famous Cornish mining engineer, visited the works in the north to examine their new machinery, and complimented the company on the very efficient new processes and machines they were then introducing. Shortly afterwards he was advising on and reconstructing lead mines in Cardiganshire, where he installed crushing rollers and round buddles. In a description of these mines and their processes, some years later, Warrington Smythe (Mems. Geol. Survey, Vol. II. 1848), says the crushing rollers were invented and introduced from the north of England, and the round buddle introduced at the same time from Cornwall; this statement seems to be a simple inversion, the round buddle first appearing in the north, and Taylor building the first crushing rolls in Cornwall in 1804 as previously described. The round buddle consisted of a circular sloping platform on to which at the centre the slimes were fed in a stream of water. A rotating arm carried stirrers or wipers to spread the slimes around the platform, along the circumference of the circles, and moved them at right angles to the run of the water, which was radially down the slope. Outside the platform was a circular trough corresponding to the trough of the ordinary buddle. In this trough the washed slimes were deposited by the water streaming from the platform and, as in the straight buddle, the ore particles settled first nearest the centre, and the lighter stuff was carried to the outer circumference. When the trough was full, it was emptied by concentric section, the ore concentrate lying nearest the centre, the waste at the outer circumference and mixed grades between. The round buddle could deal with 12 tons of slimes a day, and was reported to be three times as efficient as the flat buddle. Many modifications were made in the buddle after this but practically all were only improvements in details, the general plan of the circular buddle being retained to the present day. The shaking table was introduced by Stagg, at Nenthead, the same year (1828) and rapidly attained the elements of its present form. It was approximately 14 by 6 ft. with raised sides, making it a shallow trough. Suspended in an inclined position by four chains, at the corners, the front pair were adjustable so that the slope could be varied. The table was shaken by a hell crank lever actuated by a cam shaft. Crushed house was thoroughly mixed by two paddle wheels, fed on to a sloping head board and distributed on the table by a stream of water. The shaking motion helped the removal of the lightest fraction and the ore concentrates were ranged on the table in regular order. When a layer 6 in. in thickness had accumulated it was removed in sections. The principal difference from the modern table was the direction of motion ; in this early form the shaking took place in the direction of the water flow and not at right angles to it, as in modern practice. Between 1828 and 1830 Petherick's hydraulic jigger was tried out and improved and rapidly came into general use. In this machine, the sieve on which the ore was washed was fixed, and water was made to pulse through it and effect the concentration. The jigger was a wooden tank about 30 by 60 in: divided into two square compartments by a division that had a gate in it for the passage of the water. In one compartment was a fixed zinc plate with 1/8 in. perforations; in the other compartment a square wooden plunger, actuated from an eccentric having a stroke of 3 in. caused the water which filled both tanks, to pulse up through the sieve and concentrate the ore at the base in a layer on the sieve, exactly as in the hand-jigging sieve. An automatic hopper feed was arranged for the jigger, and various devices added for nearly continuous removal of concentrates and wastes. A mechanical brake sieve was invented by Captain Barrett, agent for the Duke of Devonshire's mines at Grassington, Yorkshire, about the same time, and was successfully operating in 1830. In this a hotching tub, or brake sieve, was used, but the motion of the sieve was applied mechanically by levers from a water wheel. In 1831 the London Lead Company reconstructed their crushing mills and added simple trommels so that systematic grading of their crushed ore could be obtained in order to suit their increased variety of machine washers. The next great period of improvement really falls into the early years of the modern period, and only the first few inventions can be mentioned here, so far as they are modifications of plant already described. In 1843, Troughton made a continuous jigger which consisted of a four-section Petherick jigger, the material being passed automatically from one compartment to another. In 1847, Brunton, working in Allendale, patented a continuous cloth separator, the rights of which the London Lead Company purchased. They at once set eight at work, four at Nenthead, and four in Teesdale. In this machine, a continuous broad belt of cloth travelled round two rollers, the tight side at the top, and slightly inclined. The top side of the cloth was stiffened by laths of wood fastened across it, at right angles to the length. Slimes and water were fed on to the cloth, the water and cloth travelling in opposite directions. This was roughly a buddle in which the concentrate was continuously carried away on the cloth. The cloth was arranged to dip into a cleaning trough where the concentrate was washed off. The cost of labour was reported by the London Lead Company to he reduced by 50 per cent, and the concentrate obtained was returned by the smelters as being 5 per cent, richer than by any earlier process. In 1849, Attwood, an employee at Nenthead, invented a slime trunking machine. The slimes were carried to a box into which water was also delivered, and the whole mixed together by revolving blades. After mixing, the material was screened through a curved perforated plate, and the waste carried off in a launder. The slime, after a further stirring and mixing, was passed on to an inclined table and washed by a stream of water into a rectangular tank, having a floor inclined about 2 deg. to the horizontal, where settling and concentration took place. The richest slime then passed to a Dolly tub for final concentration. Attwood's machine had three trunking boxes and one Dolly tub, working in conjunction, and proved fairly successful. In 1855, Zenner rotating buddles were introduced in the north of England, and in 1859 Borlase, again working in the north, invented his conical separator. This, with the introduction of the Blake stone breaker (invented by Blake in America, in 1858), almost completely changed the aspect of an ore dressing floor, and at most of the large mining concerns, the washing was transferred from the large outdoor areas, into a series of machine shops. The water wheel remained the main source of power right to the end of the century, when mining in this country suffered its greatest decline; many of the scenes of the inventions described in this paper passed into ruins and today are barely traceable. Drawings and Photographs accompanying the article
Article reproduced from a copy of the magazine held at National Mining Museum Scotland, Newtongrange, Midlothian.
|
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 17 Jan 2023
|
Search |
|
|||