|
Loads and Allowable Stresses Headgears should be designed for (a) dead load, (b) working load, (c) breaking load, and (d) wind load. (a) The dead load comprises the weight of the headgear and its sheaves, gallows, etc. The allowable stresses are based on a factor of safety of 4. Snow is considered as dead load. (b) The working loads are those due to hoisting and lowering, and the allowable stresses are based on a safety factor of 6. The maximum working load on the rope occurs when the loaded skip or cage is started suddenly from the bottom of the shaft. It then consists of the combined weight of the skip and its contents — or the cage, cars and ore — and the rope from the sheave, the impact due to starting, and the friction of the rope on the sheave, the sheave bearings, and the skip or cage in the guides. This working load may be taken from the formula:– L = 2W + R + (W + R) f, for a vertical shaft, or L = (2W + R) sin θ + f (W + R) cos θ, for a shaft inclined at θ° from the horizontal. Where L the working load in pounds; W = the weight of the skip, ore, bridle and safety hook, or that of the cage, cars, ore, chains and hook, in pounds; R = the weight of the rope in pounds; J = the co-efficient of friction 0.02 for vertical shafts, or 0.04 for inclined shafts, with the rope supported on rollers. The working load in the lowering compartment must be considered at the same time as the above load. The same formula is used, but in this case, the weight of the ore is omitted from W, and the weight of the rope is very small. In multiple compartment shafts, the hoisting and lowering working loads must be taken as applying simultaneously throughout. (c) The breaking load is that due to one hoisting rope breaking, which may happen if the skip or cage sticks in the shaft, or if the winding engine brakes are suddenly applied. In this case, the load equals the breaking load of the rope, and the allowable stress is based on a factor of safety of 2.2/3. The hoisting and lowering working loads in the other compartments must be considered along with the breaking load in the compartment concerned. (d) The wind load may be taken as a horizontal pressure of 30 lb. per sq. ft. of exposed surface, and assumed as applying at the joints in the structure. The allowable stress is based on a factor of safety of four. The sizes of the members in the headgear must be calculated to withstand stresses due to (a), (b), and (d) combined, or (a), (c) and (d) combined; whichever requires the greater sections. The resolution of the loads by stress diagrams and the determination of the sections required are purely structural engineering problems. To provide for corrosion, no sections or plates less than 5/16 in. thick should be used. Headgears should be given one coat of paint before assembly and two coats after erection, and they should be re-painted every three or four years. Accessory Equipment Mine cars are constructed of steel in sizes to suit the underground conditions, and the average weight of a car is about one-third that of the ore it carries. Cages are usually designed to take one car per deck, and are made with either one, two or three decks. The cage is generally connected to the safety hook shackle by means of six sling chains, and sometimes safety catches are also provided which grip the guides if the hoisting rope should break. The approximate weight of a steel cage equals from 75 to 100 per cent. of the total weight of its contents. Landing keps are situated at the banking level to prevent the cage dropping back into the shaft. These consist of four wrought iron arms, two for each end of the cage, carried on shafts which are connected and operated by levers. Usually, they act automatically after the cage has been raised and must be released before the cage can descend. Skips are generally made of steel, and they weigh from one half to two-thirds of the ore they carry. To guard against spillage in the shaft, skips should only be filled to 80 per cent. of their nett volume. During recent years, duralumin and other aluminium alloys have been increasingly used in the construction of mine skips and cages for deep shafts. These materials produce skips and cages 40 and 50 per cent. lighter respectively than their equivalents in steel; and although the first cost is much higher, the operating costs are lower, because more ore can be raised for the same power in existing mines, or less power — and therefore smaller winders and lighter ropes and headgears — is required for a given tonnage in new mines. A duralumin cage for a South African mine is shown in Figure 8. Safety hooks are placed between the skip bridle or the cage slings and the hoisting rope in order to prevent accidents due to overwinding. In connection with each hook, a detaching case is fitted to girders below the head sheaves, and in the event of an overwind the hook becomes locked in the case, thus suspending the skip or cage, while the hoisting rope is simultaneously liberated. Hoisting ropes of round section are most commonly used, and these generally have six strands, each consisting of nineteen wires twisted together, wound on a hemp core. Wires of crucible or plough steel, with ultimate tensile strengths of 75 or 100 tons per sq. in., are usually employed. The area of the steel in the rope is approximately 40 per cent, of the diameter squared, and therefore the ultimate breaking strengths in tons for crucible and plough steel ropes may be taken as 30 and 40 times the diameter squared respectively. The weight of steel hoisting ropes in pounds per foot is equal to 1.58 times the diameter squared. In ore mining, the maximum working load on the hoisting rope — determined by the formula given above — should not exceed one-sixth of the breaking strength of the rope. This formula does not take rope bending stresses into account, but the latter may be disregarded if the winding sheaves and drums are correctly proportioned. If rope bending stresses have to be considered, the sum of these and the working load due to direct pull should not exceed one-third of the breaking strength of the rope. Head sheaves should be as large as can be conveniently used so as to keep the rope bending stresses as low as possible. The diameter of the sheave should be at least 96 times the diameter of the rope to give satisfactory results. For medium loads, the sheave rim and boss are made of cast iron, and the spokes — which are cast in — are made of round mild steel. Sheaves up to 8 ft. diameter are usually made whole, but above this size, they are generally built in halves and bolted together, while the bosses are further strengthened by having wrought iron hoops shrunk on. For heavy loads, the sheave rim and boss are made of cast steel, the former in segments and the latter in halves machined and bolted together, and the spokes are made of mild steel flats or channels with rounded ends bolted to machined sockets in the castings. Winding drums are made with grooved faces of such a width that they will take both hoisting ropes plus three coils of each rope. The ropes are fixed at the ends of the drum and the three coils referred to remain on the drum when the skip or cage is at its lowest position. The drum is sometimes cylindrical, but more often it is in the form of a double truncated cone with the small diameter in use when the load is at the bottom of the shaft. The latter type is designed to make the work on the winding engine as nearly uniform as possible throughout the wind. The average diameter of the drum is usually made equal to the diameter of the head sheave. Hoisting in mine shafts is commonly done in two, four or six compartments, which are worked in pairs by separate winders ; and, of course, in each pair, the loaded skip or cage ascends while the empty one descends. This hoisting in balance causes a considerable saving in power. In deep mines, the weight of the rope in the shaft becomes a large part of the load, and sometimes means are employed to overcome this. These include the use of a tail rope, which is connected to the bottom of each cage and runs round a weighted sheave at the bottom of the shaft. In some cases of a very deep winding, tapered round hoisting ropes, which are smaller in diameter at the lower end, are used. The usual limit for vertical hoisting in one wind is 6,000 ft. with parallel winding ropes, but it is claimed that tapered ropes can be used for twice this depth. In mine shafts, rigid skip or cage guides are invariably used. These are sometimes made of timber, but steel rails or special steel guide sections are preferable. The guides are supported by girders fitted in the shaft compartments and the shaft framing. The guides in the shaft framing, for a distance of about 30 ft. above the shaft collar, are often hinged for the easy removal and replacement of skips and cages. In the case of headgears using both skips and cages, special changing gears, suspended from beams between the main and back legs, are used so that the change from skips to cages and vice versa can be effected in a few minutes. Simmer and Jack headgear A few notes regarding the headgear recently installed at South Deep Shaft, which is one of the largest headgears in the world, may not be out of place. This structure is shown in Fig. 1. The headgear is 160 ft. high from the shaft collar to the sheave centres, and the sheave gallows rise for a further 32 ft. It is arranged for a rectangular shaft with six compartments, each measuring 10 ft. by 5 ft. inside the timbers. Two compartments are used for triple-deck cages, each carrying 81 men or ore in cars, and the other four are used for ore skips of eight tons capacity each. The winding sheaves, which are of the built-up type having cast iron rims and bosses, and mild steel channel arms, are 14 ft. diameter and suitable for 2 in. diameter ropes The headgear contains about 400 tons of structural steel, including high tensile members in the main and back legs. In addition to the usual stairways to the sheave and safety catchplate platforms, an electric lift is installed for speedier access. Drawings and Photographs accompanying the article
Article reproduced from a copy of the magazine held at National Mining Museum Scotland, Newtongrange, Midlothian.
|
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 17 Jan 2023
|
Search |
|
|||