|
William Willis
Number 51 on the list occurred at Framwellgate Colliery on the 6th of November, about 5.30 o'clock a.m., causing the death of William Willis, a sinker. The shaft in which this accident happened is situated about 1½ miles south of the main or coal-drawing shafts, and has only recently been sunk for the purposes of improving the ventilation, and to send the men to and from work, the faces of the working places being in its vicinity. At the time of the accident the shaft was not quite complete. Two cages had been put in on the north and south sides respectively ; they were single decked cages and carried two tubs end to end, the length of the cage being 9 feet 2½ inches over all. The guides were of wire rope, and there were two to each cage, secured at the top and bottom of the shaft by screw bolts to timbers. They were both on the same side of the cage — that next to the shaft walling. There were also two wire rope from the top timbers and fastened at the bottom of the shaft to the same timbers as the guides and in a similar way, and they passed down the centre of the pit, but were not attached to the cages ; they were simply put in to prevent the cages striking at meetings, where there was a clearance of nine inches. The south cage was put in first, on the 2nd of November, and it was found that the corners next to the side of the shaft came within five and six inches of the walling respectively, while running in the shaft. The north cage was put in two days later, and both corners of it were six inches from the walling. It was intended on the day of the accident to move the south cage round as it was running too near to the shaft side, and also to tighten the guide ropes, and I was told after the accident occurred that it had always been the intention of the management to put in two extra guide ropes to each cage, opposite to those on the outer sides, to pass through rings attached to the cages, and to secure them in the same way as the other guides. A plan was also produced, which showed this system, four guides to each cage, and it was stated to be the original plan. Deceased, along with two other men, was employed to do the necessary work to complete the shaft. On the morning of the day in question, the engineer went down the shaft with deceased to show him some work which required to be done and for which he wanted some timber down the pit. Deceased, therefore, came to bank and got two lengths, one 15 feet long X 7 inches X 1¾ inches, and the other the same size, except its length, and it was 9 or 10 feet long. They were put on to the top of the south cage on their ends and secured to the cage chains by means of strong cord ; he then got on beside them and another man inside the cage. The banks man then lowered the cage gently down the shaft and very soon after it was heard to strike against something, and this was almost immediately followed by a rumbling noise. The cage was at once brought to the surface and it was found that the man was alright inside the cage, but that deceased had been thrown off the top into the shaft, and precipitated to the bottom,. A distance of 120 yards. The man who was in the cage said at the inquest, "After the deals were put, and Willis got on to the top of the cage, I got inside and we were lowered down very gently and quite steadily. There was nothing wrong until we got to the water ring, 78 feet from the surface, when the bottom corner of the cage next to the walling caught it and canted the cage over a little and then slipped off with a jerk. I then heard deceased falling down the shaft. I shouted 'Hold' and the cage was then drawn to bank." This I have no doubt, is the correct explanation of how the accident occurred. In all my experience I have never known long cages like these with only two guide ropes, and where four rope guides are used I have never seen two ropes hanging between the cages, and I am inclined to think it was intended to try if two guides for each cage could be done without. I know it was intended, if this accident had not occurred, to send all the colliers, working in the districts near to, down this shaft on that day. It is fortunate that this was not done, or there might have been an accident causing much greater loss of life. I made a careful examination of the shaft, and found the cages, in several places were running too close to the shaft walling, and that with the two guides, I could make the cage swing in such a way to cause it to go into the centre of the shaft and then come back and strike the walling. Since this accident happened each cage was been fitted with four guides, and the distance between the cages and the walling enlarged where necessary. Several other suggestions I made, to effect greater safety, have also been carried out.
If you are researching William Willis (e.g. for family tree purposes) and you would like to hear from others with the same interest then please complete the details in the following form. We will show the information you provide on this page so that you can be contacted.
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 30 Apr 2023
|
Search |
|
|||