|
February, 1951 Equipment for continuous miningThe possibility of winning coal in a single operation without previous preparation by cutting and shooting has always held many attractions for mining engineers, but it is not until recent years that systems capable of realising this ideal have begun to pass through the experimental stage and to become available to mine managements as accepted methods of working. The introduction of the coal plough, followed by the developments of various stripping machines, now makes certain that continuous mining, which involves the removal of coal from the face in relatively thin slices, will become a major method of mining. An essential requirement of continuous mining is a suitable conveyor, one that will run when curved or "snaked" so that it can be placed in front of the face timber and kept close to the coal for its full length, and which, moreover, is capable of bearing the weight of a coal-cutter and providing a runway for it, or of taking the side thrust from a stripping machine. A further requirement is a method of roof support by which the roof next to the face can be supported from props behind the conveyor without sacrifice of safety, a method which allows the supports to be advanced to coincide with the movement of the face and which, by simplifying the operation of timbering, helps to speed up the operational cycle. While equipment of this kind is essential on coal-plough and stripping faces, it also offers many advantages on faces where long-accepted methods of coal getting are in use, and it has been applied with considerable success in conjunction with pneumatic picks, etc. The Huwood P40 "Python" conveyor has been designed specifically to lie next to the face within the face timber. It is a strongly-made chain conveyor, which can be snaked to keep it close to the face, jacks set against the timber being the means normally adopted to accomplish this. Once this conveyor has been installed on the face, it is possible to run it until a complete panel of coal has been worked out, an operation which might take some months, without once breaking the conveyor. On the other hand, the P40 can, if necessary, be used on ordinary longwall faces as it is designed so that it can be easily dismantled. It thus provides a useful alternative to a belt conveyor, an important factor in view of the high cost of belting. The P40 section is made in four parts — a bottom trough, a top trough and two interlocking side angle plates In addition to these parts, spillplates can be used on one or both sides of the conveyor. The bottom troughs are made so that one overlaps the other, two welded-on stoppers on the outsides of the overlapping trough fitting into a space provided on the inner side of the under trough. Each space allows about a ½ in. play so that the two adjacent troughs can be set at an angle of 1 1/3 deg. to each other in either direction. The top trough is laid directly on the bottom trough and is held in position at four points by locating pieces fitted into the bottom trough. Bottom trough and top trough are locked firmly together at each side by interlocking side-angle plates. These plates are dropped into slots in the bottom trough, the angles covering the chains, and are pushed approximately 1½ in. in either direction, so that they interlock with the locking pieces in the sides of the bottom trough, thus making a firm and flexible structure. As has already been stated, the troughing is strong enough to support a coalcutter, but as the coalcutter moving in one direction would tend to pull the angle plates along with it, the double lock ensures that the plates will still assume a new locking position. The carrying medium in the P40 conveyor is a double chain to which flights are fitted at 3-ft. intervals. The chain has ½ in. dia. links and a breaking strain of 25 tons. Each strand is prestretched before delivery to 10 tons, to minimise the possibility of further extension, which might occur in normal running. The choice of two drive heads is provided for use with the Python conveyor. One, the P35, is used solely for tail-end drive when the conveyor is used on downward gradients. The driving motor is placed within the frame of the drive head at right-angles to the conveyor, which it drives through spur-and-pinion gearing, a Huwood reduction gearbox, similar to those used on many Huwood belt conveyors, being incorporated. The drive head can be supplied to give chain speeds of 117 ft., 158 ft. and 184 ft. per min. In the other drive head, the P40, the driving unit, consisting of motor and gearbox, can be bolted to either side of the head frame. The gearbox contains spiral-bevel and double-helical gearing which gives cool running under load, and the conveyor is so arranged that either one or two of these P40 drive units can be set to the work of driving the conveyor, one at the head end and, if required, one at the tail end. When more than one drive unit is used, any unit in which the prime mover is an electric motor is fitted with a traction-type fluid coupling between motor and gearbox in order to equalise the load. Where only one drive unit is used, either a fluid coupling or a flexible bobbin coupling can be fitted. The motor is carried in a frame bolted to both the gearbox and head frame, and it is also spigoted to the gearbox to ensure the alignment of the coupling. The P40 drive unit gives chain speeds of 142 ft., or 176 ft. per min. A larger version of the Python conveyor is available in the P80 conveyor, which is of heavier and stronger construction and capable of dealing with a longer face. In the P80 conveyor, the section differs considerably from the P40, as each trough is made in one piece of two pressings with welded-on reinforcement plates. The joint is formed by the overlap of the centre plate, and V pieces project from one end of the side channels and engage with pockets on the opposing section. The sections are loosely bolted together with two bolts which give a flexibility of 3½ deg. in all directions. Goaf spillplates may be bolted to the sections if required. In the P80 conveyor the chain has a diameter of 0.71 in. and a breaking strain of 50 tons, and is fitted with flights spaced at 3 ft. 3 in. intervals. For driving the P80 conveyor, power units very similar to the P40 drive unit are used, and as many as four can be fitted to the conveyor, two at the head end and two at the tail end, thus providing a maximum of 160 h.p., the drive from an electric motor being transmitted invariably through a traction-type fluid coupling. The drive head of the P80 conveyor can be arranged to give chain speeds of 110 ft., 149 ft. and 185 ft. per min. The Schloms bar The Schloms bar is available in either steel or light-metal alloy, and we understand that the records from one Continental colliery show that when the steel bar was introduced it made possible a very considerable improvement in the tons per manshift, a figure which was increased still further when the light-metal alloy bar was introduced and offered the advantages of even greater ease of handling. The Schloms light-metal alloy bar is of "H" section, cast with a specially strengthened web. The two ends of the bar, however, are different from each other, one end taking the form of a strongly reinforced vertical slot which receives the tapered end of the next bar. Both ends are drilled so that the two ends can be hinged together by inserting a steel pin through the holes. The tapered end of the bar contains a steel strengthening insert, and when the extension bar is lifted into a horizontal position, a steel wedge can be inserted behind this insert through apertures in the slotted part of the supporting bar. The wedge fits against the steel insert at a point below its centre, and thus holds the extension bar in any required position near to the horizontal demanded by the angle of the roof, the wedge and insert being in compression. Tests have proved that an extension bar, when wedged to a supported bar in this manner, can hold a weight of more than two tons applied to the steel pin at the extended end. It can be seen that the bar, when supported from behind the conveyor thus provides adequate support under the roof next to the face. The upper and lower flanges are provided with seatings which fit the heads of the Schwarz props normally used in conjunction with them these seatings prevent the props from slipping out of position under pressure. Owing to the bar being symmetrical, it can be reversed in the pit each time it is moved forward, so that any slight bending may be corrected The Schwarz prop The accompanying photographs show Schloms bars, Schwarz props and a Python conveyor in use at a Durham colliery. It is claimed that the Schwarz prop offers uniform resistance to the roof throughout the full travel of the upper member of the prop into the lower member. We understand that in certain former yielding props the yield was never quite uniform. Consequently, different resistances were imposed against the descending roof throughout the length of the coal face, a condition which did not make for satisfactory roof control. By making it possible to have an even resistance for the entire supported area of the face, the Schwarz prop adds both to the safety and to the efficiency of longwall working. In construction, the Schwarz prop consists of an upper and a lower member, fitted with a special clamping device which is fitted to the top of the lower member. The upper prop is extended by driving lifting wedges into slots in the lower portion of the prop, and by this means alone it is possible to obtain an initial resistance of five tons when setting. When the initial resistance has been obtained, the horizontal wedge in the clamping device is tightened and the lifting wedges withdrawn. As the pressure of the roof increases, a vertical wedge in the clamping device tightens until, after the prop has sunk only one inch, the maximum resistance is attained. This maximum resistance can according to the type of prop used, be 35 or 50 tons. The action of the wedges can best be understood from the accompanying sketches. The Schwarz prop head is fitted with horns at each of the four corners and these interlock with the seatings on the flanges of the Schloms bars, and thus prevent slip in any direction. Withdrawal may be effected either by hand or by means of a winch. An eccentric bolt holds the horizontal wedge in position, and when this bolt is rotated by lightly hammering or pulling the release lever fitted to it, the wedge is released and the upper member falls into the lower member. A common practice is to withdraw three props together, different lengths of chain being attached to a single rope operated by a winch. The lengths of these chains are so arranged that the pull is applied to each of the three props in succession through hooks attached to the release levers. Drawings and Photographs accompanying the article
Article reproduced from a copy of the magazine held at National Mining Museum Scotland, Newtongrange, Midlothian.
|
![]() |
||||||||
|
Mail: Webmaster |
Back |
Home |
Copyright © 1999-2024 by The Durham Mining Museum and its contributors Registered Charity No: 1110608 Page last updated: 17 Jan 2023
|
Search |
|
|||